Plug-and-Play-HOWTO
David S.Lawyer
<mailto:dave@lafn.org>
v1.13, July 2005
Explains resources used in Plug-and-Play (PnP) such as addresses,
interrupts, etc. Covers both the PCI bus (inherently PnP) and PnP on
the old ISA bus. If PnP did it's job right, you wouldn't need this
howto. Otherwise, this will both explain PnP and help you detect and
assign resources to hardware (low level configuring). It doesn't
cover what's called "Universal Plug and Play" (UPnP).
______________________________________________________________________
Table of Contents
1. Introduction
1.1 1. Copyright, Trademarks, Disclaimer, & Credits
1.1.1 Copyright
1.1.2 Disclaimer
1.1.3 Trademarks.
1.1.4 Credits
1.2 Future Plans; You Can Help
1.3 New Versions of this HOWTO
1.4 New in Recent Versions
1.5 General Introduction. Do you need this HOWTO?
2. What PnP Should Do: Allocate "Bus-Resources"
2.1 What is Plug-and-Play (PnP)?
2.2 Hardware Devices and Communication with them
2.3 Addresses
2.4 I/O Addresses (principles relevant to other resources too)
2.5 Memory Ranges
2.6 IRQs --Overview
2.7 DMA (Direct Memory Access) or Bus Mastering
2.8 DMA Channels (not for PCI bus)
2.9 "Resources" for both Device and Driver
2.10 Resources are Limited
2.10.1 Ideal Computers
2.10.2 Real Computers
2.11 Second Introduction to PnP
2.12 How Pnp Works (simplified)
2.13 Starting Up the PC
2.14 Buses
2.15 How Linux Does PnP
2.16 Problems with Linux PnP
3. Setting up a PnP BIOS
3.1 Do you have a PnP operating system?
3.1.1 Linux prior to the 2.4 kernel
3.1.2 Windows 2000 and XP
3.1.3 MS Windows 95, 98 (and Me ?)
3.2 Assigning Resources by the BIOS
3.3 Reset the configuration?
4. How to Deal with PnP Cards
4.1 Introduction to Dealing with PnP Devices
4.2 Device Driver Configures, Reserving Resources
4.3 /sys User Interface Configures
4.4 BIOS Configures
4.4.1 Intro to Using the BIOS to Configure PnP
4.4.2 The BIOS's ESCD Database
4.4.3 Using Windows to set the ESCD
4.4.4 Adding a New Device (under Linux or Windows)
4.5 ISA cards only: Disable PnP ?
4.6 ISA Bus: Isapnp (part of isapnptools)
4.7 PCI Utilities
4.8 Windows Configures
4.9 PnP Software/Documents
5. Tell the Driver the Configuration ??
5.1 Introduction
5.2 Serial Port Driver Example
6. How Do I Find Devices and How Are They Configured?
6.1 Finding and How-Configured Are Related
6.2 Devices May Have Two "Configurations"
6.3 Finding Hardware
6.4 Boot-time Messages
6.5 The /proc Directory Tree
6.6 The /sys Directory Tree
6.7 PCI Bus Inspection
6.8 ISA Bus Introduction
6.9 ISA PnP cards
6.10 LPC Bus
6.11 Non-PnP Cards
6.12 Non-PnP Cards with jumpers
6.13 Neither PnP nor jumpers
6.14 Tools for Detecting and/or Configuring all Hardware
6.15 Tool for Detecting and Configuring One Type of Hardware
6.16 Use MS Windows
7. PnP for External and Plug-in Devices
7.1 USB Bus
7.2 Hot Plug
7.3 Hot Swap
7.4 PnP Finds Devices Plugged Into Serial Ports
8. Error Messages
8.1 Unexpected Interrupt
8.2 Plug and Play Configuration Error (Dell BIOS)
8.3 isapnp: Write Data Register 0xa79 already used (from logs)
8.4 Can't allocate region (PCI)
9. Interrupt Conflicts
10. Appendix
10.1 Universal Plug and Play (UPnP)
10.2 Address Details
10.2.1 Address ranges
10.2.2 Address space
10.2.3 PCI Configuration Address Space
10.2.4 Range Check (ISA Testing for IO Address Conflicts)
10.2.5 Communicating Directly via Memory
10.3 ISA Bus Configuration Addresses (Read-Port etc.)
10.4 Interrupts --Details
10.4.1 DMA
10.4.2 Soft interrupts
10.4.3 Hardware interrupts
10.5 PCI Interrupts
10.6 ISA Isolation
10.7 Bus Mastering and DMA resources
10.8 Historical and Obsolete
10.8.1 OSS-Lite Sound Driver
10.8.2 ALSA (Advanced Linux Sound Architecture) as of 2000
10.8.3 MS Windows Notes
______________________________________________________________________
[1m1. Introduction[0m
[1m1.1. 1. Copyright, Trademarks, Disclaimer, & Credits[0m
[1m1.1.1. Copyright[0m
Copyright (c) 1998-2005 by David S. Lawyer <mailto:dave@lafn.org>
Please freely copy and distribute (sell or give away) this document in
any format. Send any corrections and comments to the document
maintainer. You may create a derivative work and distribute it
provided that you:
1. If it's not a translation: Email a copy of your derivative work (in
a format LDP accepts) to the author(s) and maintainer (could be the
same person). If you don't get a response then email the LDP
(Linux Documentation Project): submit@en.tldp.org.
2. License the derivative work in the spirit of this license or use
GPL. Include a copyright notice and at least a pointer to the
license used.
3. Give due credit to previous authors and major contributors.
If you're considering making a derived work other than a translation,
it's requested that you discuss your plans with the current
maintainer.
[1m1.1.2. Disclaimer[0m
While I haven't intentionally tried to mislead you, there are likely a
number of errors in this document. Please let me know about them.
Since this is free documentation, it should be obvious that I cannot
be held legally responsible for any errors.
[1m1.1.3. Trademarks.[0m
Any brand names (starts with a capital letter such as MS Windows)
should be assumed to be a trademark). Such trademarks belong to their
respective owners.
[1m1.1.4. Credits[0m
· March 2000: Daniel Scott proofread this and found many typos, etc.
· June 2000: Pete Barrett gave a workaround to prevent Windows from
zeroing PCI IRQs.
· August 2004: Ross Boylan found typos, etc. and pointed out lack of
clarity in telling the BIOS if it's a PnP OS
[1m1.2. Future Plans; You Can Help[0m
Please let me know of any errors in facts, opinions, logic, spelling,
grammar, clarity, links, etc. But first, if the date is over a few
months old, check to see that you have the latest version. Please
send me any info that you think belongs in this document.
I haven't studied the code used by various Linux drivers and the
kernel to implement Plug-and-Play. But I have sampled a little of it
(especially some of the comments). Thus this HOWTO is still
incomplete. It needs to explain more about "hot swapping", "hot-plug"
and about the new PnP software for kernel 2.6. The history of Linux
PnP is not well covered. Also, it doesn't cover firewire. It likely
has some inaccuracies (let me know where I'm wrong). In this HOWTO
I've sometimes used ?? to indicate that I don't really know the
answer.
[1m1.3. New Versions of this HOWTO[0m
New versions of the Plug-and-Play-HOWTO should appear every few months
or so and will be available to browse and/or download at LDP mirror
sites. For a list of mirror sites see:
<http://tldp.org/mirrors.html>. Various formats are available. If
you only want to quickly check the date of the latest version look at:
<http://tldp.org/HOWTO/Plug-and-Play-HOWTO.html>. The version you are
now reading is: v1.13, July 2005 .
[1m1.4. New in Recent Versions[0m
For a full revision history going back to the first version see the
source file (in linuxdoc format) at
<http://www.ibiblio.org/pub/linux/docs/HOWTO/other-formats/sgml/Plug-
and-Play-HOWTO.sgml.gz>
v1.13 July 2005: IRQ conflicts. Better clarity in resource
descriptions. /proc/bus. PCI configuration space accessed via IO
address space. More hardware detection tools. "Can't allocate
region" error message. v1.12 March 2005: /dev/eth0 doesn't exist
anymore. Info in /sys and /proc changed for kernel 2.6. PCI Config.
address space is "geographic". scanpci may find a device that lspci
can't. Kernel may assign addresses at boot-time. v1.11 November
2004: LPC bus. Format error (text in contents) v1.10 August 2004:
sysfs not yet as useful as claimed, obsolete card info moved to
"Historical" section. v1.09 August 2004: Edited per email from Ross
Boylan (ross@biostat.ucsf.edu). Clarity re telling BIOS if it's a PnP
OS. /proc/isapnp covered. Typos fixed. sysfs in kernel 2.6. v1.08
June 2004: Edited all except appendix for more clarity and to correct
some obsolete statements in view of the increasing PnP abilities of
Linux. Added brief info on "hot plug" and USB.
[1m1.5. General Introduction. Do you need this HOWTO?[0m
Plug-and-play (PnP) is a system which automatically detects devices
such as disks, sound cards, ethernet cards, modems, etc. It finds all
devices on the PCI bus and all devices that support PnP on the old ISA
bus. Before PnP, many devices were automatically searched for by non-
PnP methods, but were sometimes not found. PnP provides a way to find
all devices that support PnP. It also does some low-level configuring
of them. Non-PnP devices (or PnP devices which have not been
correctly PnP-configured), can often be detected by non-PnP methods.
The PCI bus is inherently PnP while the old ISA bus originally wasn't
PnP but had PnP support added to it later. So sometimes PnP is used
to only mean PnP for the old ISA bus. For example, when you see a
boot-time message from "isapnp" and it reads: "Plug & Play device" it
only means a ISA Plug & Play device. In this HOWTO, PnP means PnP for
both the ISA and the PCI bus.
As time goes by the Linux kernel is became better at supporting PnP.
In the late 20th century, one could say that Linux was not really a
PnP OS. But the claim is made that with version 2.6 of the kernel,
Linux is now fully PnP (provided the kernel is built with appropriate
PnP support). While the PnP system is not centralized like it is in
MS Windows (with its registry) the decentralized Linux PnP seems to
work OK.
Linux does keep track of resource assignments requested by device
drivers and refuses any request if it thinks it would cause a
conflict. The kernel also provides programs that device drivers can
call on to do their own plug-and-play. The kernel also reads all
configuration registers of all PnP devices and maintains tables of
them that device drivers can consult. This table helps drivers find
their hardware. Kernel 2.6 provides better support for "hot plug".
The BIOS hardware of your PC likely does some plug-and-play work too.
Thus if everything works OK PnP-wise, you can use your computer
without needing to know anything about plug-and-play. But if some
devices which are supported by Linux don't work (because they're not
discovered or configured correctly by PnP) then you may need to read
some of this HOWTO. You'll learn not only about PnP but also learn
something about how communication takes place inside the computer. If
you have a modern computer with a PCI bus but no ISA bus, you may skip
over or skim the parts about the ISA bus.
If you're having problems with a device, watch the messages displayed
at boot-time (go back thru them using Shift-PageUp). If this doesn't
also display early messages from the BIOS use the "Pause" key. See
``Pause''
Check to see that you have the right driver for a device, and that the
driver is being found and used. If the driver is a module, type
"lsmod" (as the root user) to see it it's loaded (in use). If it's
not a module then it should be built into the kernel.
This HOWTO doesn't cover the problem of finding and installing device
drivers. Perhaps it should. One problem is that a certain brand of a
card (or other physical device) may not say what kind of chips are
used in it. The driver name is often the same as the chip name and
not the brand name. One way to start to check on a driver is to see
if it is discussed in the kernel documentation, in another HOWTO, or
on the Internet. Warning: Such documentation may be out of date.
The PCI bus computers (no ISA bus) have significantly reduced the
number of things that can go wrong. For the ISA bus and the lack of
kernel support for ISA Pnp (before kernel 2.4), there was much more
that could go wrong. Remember that sometimes problems which seem to
be PnP related are actually due to defective hardware or to hardware
that doesn't fully conform to PnP specs.
[1m2. What PnP Should Do: Allocate "Bus-Resources"[0m
[1m2.1. What is Plug-and-Play (PnP)?[0m
If you don't understand this section, read the next section ``Hardware
Devices and Communication with them''
Oversimplified, Plug-and-Play tells the software (device drivers)
where to find various pieces of hardware (devices) such as modems,
network cards, sound cards, etc. Plug-and-Play's task is to match up
physical devices with the software (device drivers) that operates them
and to establish channels of communication between each physical
device and its driver. In order to achieve this, PnP allocates and
sets the following "bus-resources" in hardware: I/O addresses, memory
regions, IRQs, DMA channels (ISA bus only). These 4 things are
sometimes called "1st order resources" or just "resources". Pnp
maintains a record of what it's done and allows device drivers to get
this information. If you don't understand what these 4 bus-resources
are, read the following subsections of this HOWTO: I/O Addresses,
IRQs, DMA Channels, Memory Regions. An article in Linux Gazette
regarding 3 of these bus-resources is Introduction to IRQs, DMAs and
Base Addresses. Once these bus-resources have been assigned (and if
the correct driver is installed), the actual driver and the "files"
for it in the /dev directory are ready to use.
This PnP assignment of bus-resources is sometimes called "configuring"
but it is only a low level type of configuring. The /etc directory
has many configuration files but most all of them are not for PnP
configuring. So most of the configuring of hardware devices has
nothing to do with PnP or bus-resources. For, example the
initializing of a modem by an "init string" or setting it's speed is
not PnP. Thus when talking about PnP, "configuring" means only a
certain type of configuring. While other documentation (such as for
MS Windows) simply calls bus-resources "resources", I sometimes use
the term "bus-resources" instead of just "resources" so as to
distinguish it from the multitude of other kinds of resources.
PnP is a process which is done by various software and hardware. If
there was just one program that handled PnP in Linux, it would be
simple. But with Linux each device driver does it's own PnP, using
software supplied by the kernel. The BIOS hardware of the PC does PnP
when a PC is first powered up. And there's a lot more to it than
this.
[1m2.2. Hardware Devices and Communication with them[0m
A computer consists of a CPU/processor to do the computing and RAM
memory to store programs and data (for fast access). In addition,
there are a number of devices such as various kinds of disk-drives, a
video card, a keyboard, network devices, modem cards, sound devices,
the USB bus, serial and parallel ports, etc. In olden days most
devices were on cards inserted into slots in the PC. Today, many
devices that were formerly cards, are now on-board since they are
contained in chips on the motherboard. There is also a power supply
to provide electric energy, various buses on a motherboard to connect
the devices to the CPU, and a case to put all this into.
Cards which plug into the motherboard may contain more than one
device. Memory chips are also sometimes considered to be devices but
are not plug-and-play in the sense used in this HOWTO.
For the computer system to work right, each device must be under the
control of its "device driver". This is software which is a part of
the operating system (perhaps loaded as a module) and runs on the CPU.
Device drivers are associated with "special files" in the /dev
directory although they are not really files. They have names such as
hda3 (third partition on hard drive a), ttyS1 (the second serial
port), eth0 (the first ethernet card), etc.
The eth0 device is for an ethernet card (nic card). Formerly it was
/dev/eth0 but it's now just a virtual device in the kernel. What eth0
refers to depends on the type of ethernet card you have. If the
driver is a module, this assignment is likely in an internal kernel
table but might be found in /etc/modules.conf (called "alias"). For
example, if you have an ethernet card that uses the "tulip" chip you
could put "alias eth0 tulip" into /etc/modules.conf so that when your
computer asks for eth0 it finds the tulip driver. However, modern
kernels can usually find the right driver module so that you seldom
need to specify it yourself.
To control a device, the CPU (under the control of the device driver)
sends commands and data to, and reads status and data from the various
devices. In order to do this each device driver must know the address
of the device it controls. Knowing such an address is equivalent to
setting up a communication channel, even though the physical "channel"
is actually the data bus inside the PC which is shared with many other
devices.
This communication channel is actually a little more complex than
described above. An "address" is actually a range of addresses so
that sometimes the word "range" is used instead of "address". There
could even be more that one range (with no overlapping) for a single
device. Also, there is a reverse part of the channel (known as
interrupts) which allows devices to send an urgent "help" request to
their device driver.
[1m2.3. Addresses[0m
The PCI bus has 3 address spaces: I/O, main memory (IO memory), and
configuration. The old ISA bus lacks a genuine "configuration"
address space. Only the I/0 and IO memory spaces are used for device
IO. Configuration addresses are fixed and can't be changed so they
don't need to be allocated. For more details see ``PCI Configuration
Address Space''
When the CPU wants to access a device, it puts the device's address on
a major bus of the computer (for PCI: the address/data bus). All
types of addresses (such as both I/O and main memory) share the same
bus inside the PC. But the presence or absence of voltage on certain
dedicated wires in the PC's bus tells which "space" an address is in:
I/O, main memory, (see ``Memory Ranges''), or configuration (PCI
only). This is a little oversimplified since telling a PCI device
that it's a configuration space access is actually more complex than
described above. See ``PCI Configuration Address Space'' for details.
See ``Address Details'' for more details on addressing in general.
The addresses of a device are stored in it's registers in the physical
device. They can be changed by software and they can be disabled so
that the device has no address at all. Except that the PCI
configuration address can't be changed or disabled.
[1m2.4. I/O Addresses (principles relevant to other resources too)[0m
Devices were originally located in I/O address space but today they
may use space in main memory. An I/0 address is sometimes just called
"I/O", "IO", "i/o" or "io". The terms "I/O port" or "I/O range" are
also used. Don't confuse these IO ports with "IO memory" located in
main memory. There are two main steps to allocate the I/O addresses
(or some other bus-resources such as interrupts on the ISA bus):
1. Set the I/O address, etc. in the hardware (in one of its registers)
2. Let its device driver know what this I/O address, etc. is
Often, the device driver does both of these (sort of). The device
driver doesn't actually need to set an I/O address if it finds out
that the address has been previously set (perhaps by the BIOS) and is
willing to use that address. Once the driver has either found out
what address has been previously set or sets the address, then it
obviously knows what the address is so there is no need to let the
driver know the address --it already knows it.
The two step process above (1. Set the address in the hardware. 2.
Let the driver know it.) is something like the two part problem of
finding someone's house number on a street. Someone must install a
number on the front of the house so that it may be found and then
people who might want to go to this address must obtain (and write
down) this house number so that they can find the house. In computers
the device hardware must first get its address it put into a special
register (put up the house number) and then the device driver must
obtain this address (write the house number in its address book).
Both of these must be done, either automatically by software or by
entering the data manually into configuration files. Problems may
occur when only one of them gets done right.
For manual PnP configuration some people make the mistake of doing
only one of these steps and then wonder why the computer can't find
the device. For example, they may use "setserial" to assign an
address to a serial port without realizing that this only tells the
driver an address. It doesn't set the address in the serial port
hardware itself. If you told the driver wrong then you're in trouble.
Another way to tell the driver is to give the address as an option to
a kernel module (device driver). If what you tell it is wrong, there
could be problems. A smart driver may detect how the hardware is
actually set and reject the incorrect information supplied by the
option (or at least issue an error message).
An obvious requirement is that before the device driver can use an
address it must be first set in the physical device (such as a card).
Since device drivers often start up soon after you start the computer,
they sometimes try to access a card (to see if it's there, etc.)
before the address has been set in the card by a PnP configuration
program. Then you see an error message that they can't find the card
even though it's there (but doesn't yet have an address yet).
What was said in the last few paragraphs regarding I/O addresses
applies with equal force to most other bus-resources: ``Memory
Ranges'', ``IRQs --Overview'' and ``DMA Channels''. What these are
will be explained in the next 3 sections. The exception is that IRQs
on the PCI bus are not set by a card register but are set by a special
routing chip on the motherboard and also puts the IRQ into a card
register for information purposes only.
To see what IO addresses are used on your PC, look at the
/proc/ioports file.
[1m2.5. Memory Ranges[0m
Many devices are assigned address space in main memory. It's
sometimes called "shared memory" or "memory-mapped IO" or "IO memory".
This memory is physically located inside the physical device but the
computer accesses it just like it would access memory on memory chips.
When discussing bus-resources it's often just called "memory", "mem",
or "iomem". In addition to using such "memory", such a device might
also use conventional IO address space. To see what mem is in use on
your computer, look at /proc/iomem. This "file" includes the memory
used by your ordinary RAM memory chips so it shows memory allocation
in general and not just iomem allocation. If you see a strange number
instead of a name, it's likely the number of a PCI device which you
can verify by typing "lspci".
When you insert a card that uses iomem, you are in effect also
inserting a memory module for main memory. A high address is selected
for it by PnP so that it doesn't conflict with the main memory modules
(chips). This memory can either be ROM (Read Only Memory) or shared
memory. Shared memory is shared between the device and the CPU
(running the device driver) just as IO address space is shared between
the device and the CPU. This shared memory serves as a means of data
"transfer" between the device and main memory. It's Input-Output (IO)
but it's not done in IO space. Both the card and the device driver
need to know the memory range.
ROM (Read Only Memory) on cards is a different kind of iomem. It is
likely a program (perhaps a device driver) which will be used with the
device. It could be initialization code so that a device driver is
still required. Hopefully, it will work with Linux and not just MS
Windows. It may need to be shadowed which means that it is copied to
your main memory chips in order to run faster. Once it's shadowed
it's no longer "read only".
[1m2.6. IRQs --Overview[0m
After reading this you may want to read ``Interrupts --Details'' for
many more details. The following is intentionally oversimplified:
Besides the address, there is also an interrupt number to deal with
(such as IRQ 5). It's called an IRQ (Interrupt ReQuest) number or
just an "irq" for short. We already mentioned above that the device
driver must know the address of a card in order to be able to
communicate with it.
But what about communication in the opposite direction? Suppose the
device needs to tell its device driver something immediately. For
example, the device may have just received a lot of bytes destined for
main memory and the device needs to tell its driver to fetch these
bytes at once and transfer them from the device's nearly full buffer
into main memory. Another example is to signal the driver that the
device has finished sending out a bunch of bytes and is now waiting
for some more bytes from the driver so that it can send them too.
How should the device rapidly signal its driver? It may not be able
to use the main data bus since it's likely already in use. Instead it
puts a voltage on a dedicated interrupt wire (part of the bus) which
is often reserved for that device alone. This voltage signal is
called an Interrupt ReQuest (IRQ) or just an "interrupt" for short.
There are the equivalent of 16 such wires in a PC and each wire leads
(indirectly) to a certain device driver. Each wire has a unique IRQ
(Interrupt ReQuest) number. The device must put its interrupt on the
correct wire and the device driver must listen for the interrupt on
the correct wire. Which wire the device sends such "help requests" on
is determined by the IRQ number stored in the device. This same IRQ
number must be known to the device driver so that the device driver
knows which IRQ line to listen on.
Once the device driver gets the interrupt from the device it must find
out why the interrupt was issued and take appropriate action to
service the interrupt. On the ISA bus, each device usually needs its
own unique IRQ number. For the PCI bus and other special cases, the
sharing of IRQs is allowed (two PCI devices may have the same IRQ
number). Also, for PCI the assignment of IRQs to devices is set by a
programmable routing chip. See ``Interrupts --Details'' for how this
works.
[1m2.7. DMA (Direct Memory Access) or Bus Mastering[0m
Direct Memory Access (DMA) is where a device is allowed to take over
the main computer bus from the CPU and transfer bytes directly to main
memory. Normally the CPU would make such a transfer in a two step
process:
1. reading a chunk of bytes from the I/O memory space of the device
and putting these bytes into CPU itself
2. writing these bytes from the CPU to main memory
With DMA it's a one step process of sending the bytes directly from
the device to memory. The device must have DMA capabilities built
into its hardware and thus not all devices can do DMA. While DMA is
going on, the CPU can't do too much since the main bus is being used
by the DMA transfer.
Both the PCI bus and the old ISA bus can do DMA, but for the PCI bus,
no DMA resources (channels) are needed. DMA on the PCI bus is
actually "bus mastering" but the term "DMA" is widely used for it. It
allows devices to temporarily become bus masters and to transfer bytes
almost like the bus master was the CPU. It doesn't use any channel
numbers since the organization of the PCI bus is such that the PCI
hardware knows which device is currently the bus master and which
device is requesting to become a bus master. Thus there is no
resource allocation of DMA channels for the PCI bus and no dma channel
resources exist for this bus.
[1m2.8. DMA Channels (not for PCI bus)[0m
This is only for the old ISA bus. When a device wants to do DMA it
issues a DMA-request using dedicated DMA request wires much like an
interrupt request. DMA actually could have been handled by using
interrupts but this would introduce some delays so it's faster to do
it by having a special type of interrupt known as a DMA-request. Like
interrupts, DMA-requests are numbered so as to identify which device
is making the request. This number is called a DMA-channel. Since
DMA transfers all use the main bus (and only one can run at a time)
they all actually use the same channel for data flow but the "DMA
channel" number serves to identify who is using the "channel".
Hardware registers exist on the motherboard which store the current
status of each "channel". Thus in order to issue a DMA-request, the
device must know its DMA-channel number which must be stored in a
special register on the physical device.
[1m2.9. "Resources" for both Device and Driver[0m
Thus device drivers must be "attached" in some way to the hardware
they control. This is done by allocating bus-resources (I/O, Memory,
IRQ's, DMA's) to both the physical device and letting the device
driver to find out about it. For example, a serial port uses only 2
resources: an IRQ and an I/O address. Both of these values must be
supplied to the device driver and the physical device. The driver
(and its device) is also given a name in the /dev directory (such as
ttyS1). The address and IRQ number is stored by the physical device
in configuration registers on its card (or in a chip on the
motherboard). For the case of jumpers (old hardware), it's the
location of the jumpers themselves that store the bus-resource
configuration in the device hardware (on the card, etc.). For the
case of PnP, the configuration register data is usually lost when the
PC is powered down (turned off) so that the bus-resource data must be
supplied to each device anew each time the PC is powered on.
[1m2.10. Resources are Limited[0m
[1m2.10.1. Ideal Computers[0m
The architecture of the PC provides only a limited number of
resources: IRQ's, DMA channels, I/O address, and memory regions. If
there were only a limited number devices and they all used
standardized bus-resources values (such as unique I/O addresses and
IRQ numbers) there would be no problem of attaching device drivers to
devices. Each device would have a fixed resources which would not
conflict with any other device on your computer. No two devices would
have the same addresses, there would be no IRQ conflicts on the ISA
bus, etc. Each driver would be programmed with the unique addresses,
IRQ, etc. hard-coded into the program. Life would be simple.
Another way to prevent address conflicts would be to have each card's
slot number included as part of the address. Thus there could be no
address conflict between two different cards (since they are in
different slots). Card design would not allow address conflicts
between different functions of the card. It turns out that the
configuration address space (used for resource inquiry and assignment)
actually does this. But it's not done for I/O addresses nor memory
regions. Sharing IRQs as on the PCI bus also avoids conflicts.
[1m2.10.2. Real Computers[0m
But PC architecture has conflict problems. The increase in the number
of devices (including multiple devices of the same type) has tended to
increase potential conflicts. At the same time, the introduction of
the PCI bus, where two or more devices can share the same interrupt,
has tended to reduce conflicts. The overall result, due to going to
PCI, has been a reduction in conflicts since the scarcest resource is
IRQs. However, even on the PCI bus it's a little more efficient to
avoid IRQ sharing and even with PCI there can still be address
conflicts.
So devices need to have some flexibility so that they can be set to
whatever address, IRQ, etc. is needed to avoid any conflicts. But
some IRQ's and addresses are pretty standard such as the ones for the
clock and keyboard. These don't need such flexibility.
Besides the problem of conflicting allocation of bus-resources, there
is a problem of making a mistake in telling the device driver what the
bus-resources are. This is more likely to happen for the case of old-
fashioned manual configuration where the user types in the resources
used into a configuration file stored on the harddrive. This often
worked OK when resources were set by jumpers on the cards (provided
the user knew how they were set and made no mistakes in typing this
data to configuration files). But with resources being set by PnP
software, they may not always get set the same and this may mean
trouble for any manual configuration.
The allocation of bus-resources, if done correctly, establishes non-
conflicting channels of communication between physical hardware and
their device drivers. For example, if a certain I/O address range
(resource) is allocated to both a device driver and a piece of
hardware, then this has established a one-way communication channel
between them. The driver may send commands and other info to the
device. It's actually more than one-way communications since the
driver may get information from the device by reading its registers.
But the device can't initiate any communication this way. To initiate
communication the device needs an IRQ so it can send interrupts to its
driver. This creates a two-way communication channel where both the
driver and the physical device can initiate communication.
[1m2.11. Second Introduction to PnP[0m
The term Plug-and-Play (PnP) has various meanings. In the broad sense
it is just auto-configuration where one just plugs in a device and it
configures itself. In the sense used in this HOWTO, PnP means the
configuring PnP bus-resources (setting them in the physical devices)
and letting the device drivers know about it. For the case of Linux,
it is often just a driver determining how the BIOS has set bus-
resources and if necessary, the driver giving a command to change
(reset) the bus-resources. "PnP" often just means PnP on the ISA bus
so that the message from isapnp: "No Plug and Play device found" just
means that no ISA PnP devices were found. The standard PCI
specifications (which were invented before coining the term "PnP")
provide the equivalent of PnP for the PCI bus.
PnP matches up devices with their device drivers and specifies their
communication channels (by allocating bus-resources). It
electronically communicates with configuration registers located
inside the physical devices using a standardized protocol. On the ISA
bus before Plug-and-Play, the bus-resources were formerly set in
hardware devices by jumpers or switches. Sometimes the bus-resources
could be set into the hardware electronically by a program (usually
written only for a MS OS) on a floppy supplied with the hardware.
This was something like PnP but there was no standardized protocol
used so it wasn't PnP. For Linux before PnP, software drivers were
assigned bus-resources by configuration files (or the like) or by
probing the for the device at addresses where it was expected to
reside. But these methods are still in use today to allow Linux to
use old non-PnP hardware. And sometimes these old methods are still
used today on PnP hardware (after say the BIOS has assigned resources
to hardware by PnP methods).
The PCI bus was PnP-like from the beginning, but at first it wasn't
called PnP (and often still isn't called PnP).
[1m2.12. How Pnp Works (simplified)[0m
Here's how PnP should work in theory. The hypothetical PnP
configuration program finds all PnP devices and asks each what bus-
resources it needs. Then it checks what bus-resources (IRQs, etc.) it
has to give away. Of course, if it has reserved bus-resources used by
non-PnP (legacy) devices (if it knows about them) it doesn't give
these away. Then it uses some criteria (not specified by PnP
specifications) to give out the bus-resources so that there are no
conflicts and so that all devices get what they need (if possible).
It then indirectly tells each physical device what bus-resources are
assigned to it and the devices set themselves up to use only the
assigned bus-resources. Then the device drivers somehow find out what
bus-resources their devices use and are thus able to communicate
effectively with the devices they control.
For example, suppose a card needs one interrupt (IRQ number) and 1 MB
of shared memory. The PnP program reads this request from the
configuration registers on the card. It then assigns the card IRQ5
and 1 MB of memory addresses space, starting at address 0xe9000000.
The PnP program also reads identifying information from the card
telling what type of device it is, its ID number, etc. Then it
directly or indirectly tells the appropriate device driver what it's
done. If it's the driver itself that is doing the PnP, then there's
no need to find a driver for the device (since it's driver is already
running). Otherwise a suitable device driver needs to be found and
sooner or later told how it's device is configured.
It's not always this simple since the card (or routing table for PCI)
may specify that it can only use certain IRQ numbers or that the 1 MB
of memory must lie within a certain range of addresses. The details
are different for the PCI and ISA buses with more complexity on the
ISA bus.
One way commonly used to allocate resources is to start with one
device and allocate it bus-resources. Then do the same for the next
device, etc. Then if finally all devices get allocated resources
without conflicts, then all is OK. But if allocating a needed
resource would create a conflict, then it's necessary to go back and
try to make some changes in previous allocations so as to obtain the
needed bus-resource. This is called rebalancing. Linux doesn't do
rebalancing but MS Windows does in some cases. For Linux, all this is
done by the BIOS and/or kernel and/or device drivers. In Linux, the
device driver doesn't get it's final allocation of resources until the
driver starts up, so one way to avoid conflicts is just not to start
any device that might cause a conflict. However, the BIOS often
allocates resources to the physical device before Linux is even booted
and the kernel checks PCI devices for addresses conflicts at boot-
time.
There are some shortcuts that PnP software may use. One is to keep
track of how it assigned bus-resources at the last configuration (when
the computer was last used) and reuse this. BIOSs do this as does MS
Windows and this but standard Linux doesn't. But in a way it does
since it uses what the BIOS has done. Windows stores this info in
its "Registry" on the hard disk and a PnP/PCI BIOS stores it in non-
volatile memory in your PC (known as ESCD; see ``The BIOS's ESCD
Database''). Some say that not having a registry (like Linux) is
better since with Windows, the registry may get corrupted and is
difficult to edit. But PnP in Linux has problems too.
While MS Windows (except for Windows 3.x and NT4) were PnP, Linux was
not originally a PnP OS but has been gradually becoming a PnP OS. PnP
originally worked for Linux because a PnP BIOS would configure the
bus-resources and the device drivers would find out (using programs
supplied by the Linux kernel) what the BIOS has done. Today, most
drivers can issue commands to do their own bus-resource configuring
and don't need to always rely on the BIOS. Unfortunately a driver
could grab a bus-resource which another device will need later on.
Some device drivers may store the last configuration they used in a
configuration file and use it the next time the computer is powered
on.
If the device hardware remembered its previous configuration, then
there wouldn't be any hardware to PnP configure at the next boot-time.
But hardware seems to forget its configuration when the power is
turned off. Some devices contain a default configuration (but not
necessarily the last one used). Thus a PnP device needs to be re-
configured each time the PC is powered on. Also, if a new device has
been added, then it too needs to be configured too. Allocating bus-
resources to this new device might involve taking some bus-resources
away from an existing device and assigning the existing device
alternative bus-resources that it can use instead. At present, Linux
can't allocate with this sophistication (and MS Windows XP may not be
able to do it either).
[1m2.13. Starting Up the PC[0m
When the PC is first turned on the BIOS chip runs its program to get
the computer started (the first step is to check out the motherboard
hardware). If the operating system is stored on the hard-drive (as it
normally is) then the BIOS must know about the hard-drive. If the
hard-drive is PnP then the BIOS may use PnP methods to find it. Also,
in order to permit the user to manually configure the BIOS's CMOS and
respond to error messages when the computer starts up, a screen (video
card) and keyboard are also required. Thus the BIOS must always PnP-
configure devices needed to load the operating system from the hard-
drive.
Once the BIOS has identified the hard-drive, the video card, and the
keyboard it is ready to start booting (loading the operating system
into memory from the hard-disk). If you've told the BIOS that you
have a PnP operating system (PnP OS), it should start booting the PC
as above and let the operating system finish the PnP configuring.
Otherwise, a PnP-BIOS will (prior to booting) likely try to do the
rest of the PnP configuring of devices (but not inform the device
drivers of what it did). But the drivers can still find out this by
utilizing functions available in the Linux kernel.
[1m2.14. Buses[0m
To see what's on the PCI bus type lspci or lspci -vv. Or type scanpci
-v for the same information in the numeric code format where the
vendor is shown by number (such as: "vendor 0x4B8C") instead of by
name, etc. In rare cases, scanpci will find a device that lspci can't
find.
The boot-time messages on your display show devices which have been
found on various buses (use shift-PageUp to back up thru them). See
``Boot-time Messages''
ISA is the old bus of the old IBM-compatible PCs while PCI is a newer
and faster bus from Intel. The PCI bus was designed for what is today
called PnP. This makes it easy (as compared to the ISA bus) to find
out how PnP bus-resources have been assigned to hardware devices.
For the ISA bus there was a real problem with implementing PnP since
no one had PnP in mind when the ISA bus was designed and there are
almost no I/O addresses available for PnP to use for sending
configuration info to a physical device. As a result, the way PnP was
shoehorned onto the ISA bus is very complicated. Whole books have
been written about it. See ``PnP Book''. Among other things, it
requires that each PnP device be assigned a temporary "handle" by the
PnP program so that one may address it for PnP configuring. Assigning
these "handles" is call "isolation". See ``ISA Isolation'' for the
complex details.
As the ISA bus becomes extinct, PnP will be a little easier. It will
then not only be easier to find out how the BIOS has configured the
hardware, but there will be less conflicts since PCI can share
interrupts. There will still be the need to match up device drivers
with devices and also a need to configure devices that are added when
the PC is up and running. The serious problem of some devices not
being supported by Linux will remain.
[1m2.15. How Linux Does PnP[0m
Linux has had serious problems in the past in dealing with PnP but
most of those problems have now been solved (as of mid 2004). Linux
has gone from a non-PnP system originally, to one that is in part a
non-centralized Pnp system (each device for itself). Thus, one can
argue that it still isn't fully PnP. PCI devices get assigned IRQs by
the BIOS at boot time. The BIOS may also assign addresses and IRQs in
the device configuration registers. It's claimed that if the BIOS
doesn't do this, the Linux kernel will (if configured to do so) before
the device driver starts up. Some documentation on the kernel just
assumed that the BIOS would always do this for the common PC
architecture and that Linux would do it for other architectures. So
it's not clear.
Then when a device driver finds its device, it asks to see what
addresses and IRQ have been assigned (by the BIOS and/or Linux ??) and
normally just accepts them. But if the driver wants to do so, it can
change the addresses, using functions supplied by the kernel but the
kernel will not accept addresses that conflict with other devices.
When the PC starts up, you may note messages on the screen showing
that some Linux device drivers have found their hardware devices and
what the IRQ and address ranges are.. Thus, the kernel provides the
drivers with functions (program code) that the drivers may use to find
out if their device exists, how it's been configured, and functions to
modify the configuration if needed. Kernel 2.2 could do this only for
the PCI bus but Kernel 2.4 has this feature for both the ISA and PCI
buses (provided that the appropriate PNP and PCI options have been
selected when compiling the kernel). This by no means guarantees that
all drivers will fully and correctly use these features.
In addition, the kernel helps avoid resource conflicts by not allowing
two devices to use the same bus-resources at the same time.
Originally this was only for IRQs, and DMAs but now it's for address
resources as well. For PCI, the kernel checks for possible address
conflicts while booting.
Prior to Kernel 2.4, the standalone program: isapnp was often run to
configure and/or get info from PnP devices on the ISA bus. isapnp is
still needed for cases where the device driver is not fully PnP for
the ISA bus. There was at least one early rejected attempt to make
Linux a true PnP operating system. See <http://www.astarte.free-
online.co.uk>. While developed around 1998 it never was put into the
kernel (but probably should have been).
To see what help the kernel may provide to device drivers see the
directory /usr/.../.../Documentation where one of the ... contains the
word "kernel-doc" or the like. Warning: documentation here tends to
be out-of-date so to get the latest info you would need to read
messages on mailing lists sent by kernel developers and possibly the
computer code that they write including comments. In this kernel
documentation directory see pci.txt ("How to Write Linux PCI Drivers")
and the file: /usr/include/linux/pci.h. Unless you are a driver guru
and know C Programming, these files are written so tersely that they
will not actually teach you how to write a driver. But it will give
you some idea of what PnP type functions are available for drivers to
use.
For kernel 2.4 see isapnp.txt. For kernel 2.6, isapnp.txt is replaced
by pnp.txt which is totally different than isapnp.txt and also deals
with the PCI bus. Also see the O'Reilly book: Linux Device Drivers,
3rd ed., 2005. It's on the Internet.
[1m2.16. Problems with Linux PnP[0m
But there are a number of things that a real PnP operating system
could handle better:
· Allocate bus-resources when they are in short supply by
reallocation of resources if necessary
· Deal with choosing a driver when there is more than one driver for
a physical device
· Find a driver for a detected device (instead of waiting for a
program to start that loads a driver).
· Full centralized allocation of bus-resources would ease the job of
programmers of device drivers
Since it's each driver for itself, a driver could grab bus-resources
that are needed by other devices (but not yet allocated to them by the
kernel). Thus a more sophisticated PnP Linux kernel would be better,
where the kernel did the allocation after all requests were in.
Another alternative would be a try to reallocate resources already
assigned if a devices couldn't get the resources it requested.
The "shortage of bus-resources" problem is becoming less of a problem
for two reasons: One reason is that the PCI bus is replacing the ISA
bus. Under PCI there is no shortage of IRQs since IRQs may be shared
(even though sharing is a little less efficient). Also, PCI doesn't
use DMA resources (although it does the equivalent of DMA without
needing such resources).
The second reason is that more address space is available for device
I/0. While the conventional I/O address space of the ISA bus was
limited to 64KB, the PCI bus has 4GB of it. Since more physical
devices are using main memory addresses instead of IO address space,
there is still more space available, even on the ISA bus. On 32-bit
PCs there is 4GB of main memory address space and much of this bus-
resource is available for device IO (unless you have 4GB of main
memory installed).
[1m3. Setting up a PnP BIOS[0m
When the computer is first turned on, the BIOS program runs before the
operating system is loaded. Modern BIOSs are PnP and can configure
most of the PnP devices. Some old PCI BIOSs will only configure the
PCI bus. Here are some of the choices which may exist in your BIOS's
CMOS menu:
· ``Do you have a PnP operating system?''
· ``How are bus-resources to be controlled?''
· ``Reset the configuration?''
[1m3.1. Do you have a PnP operating system?[0m
Regardless of how you answer this to the BIOS, the PnP BIOS will PnP-
configure the hard-drive, floppy, video card, and keyboard to make the
system bootable. If you said you had a PnP OS it will leave it up to
the operating system (or device drivers) to finish the configuration
job. If you said no PnP OS then the BIOS should configure everything.
How should you answer this question to your BIOS? If you have at at
least the 2.4 kernel you could answer it either way and Linux will
usually work fine. But if Linux can't handle something that the BIOS
can (possibly the LPC bus ??), then you should say it's not a PnP OS.
Even if you have have Windows 2000 or XP on the same PC, it will
usually work OK either way. This is because both Windows and Linux
are supposedly PnP OS's and if the OS is PnP it should be able to also
handle the case where the BIOS has configured everything (if you said
it wasn't PnP). But I still suggest saying that it's not a PnP OS
unless there is a known reason to say otherwise.
[1m3.1.1. Linux prior to the 2.4 kernel[0m
It's not often clear whether to say yes or no. If isapnp was used by
Linux, then Linux does the configuring and it was claimed that it's
best to say it's a PnP OS. Why isapnp would have trouble when
presented with devices already configured by the BIOS isn't clear, but
such trouble sometimes happened and was fixed by stopping the BIOS
from configuring (saying yes, it's a PnP OS). There were a few cases
where saying no fixed a problem. So if isapnp is doing it's job OK,
you should probably say it's PnP. If isapnp isn't used, no is usually
best. The Linux device drivers for PCI devices should configure PCI
devices OK. But for the case of PCI devices driven by non-PCI
drivers, then you may say it's not PnP to get the BIOS to configure
them.
[1m3.1.2. Windows 2000 and XP[0m
If you also run these Windows OS's on the same PC, you should say that
you don't have a PnP OS. That's what MS suggests you do. Perhaps MS
hopes that the BIOS will do a better job at configuring than Windows
will. That makes sense because the BIOS should be designed for the
particular idiosyncrasies of the motherboard, especially today when
many devices are built into the motherboard. PnP OS = no should also
be OK for Linux kernels 2.4 and higher. But for Linux kernel prior to
2.4, it's not clear which is best. (see the above subsection). So if
you have problems with Linux you might try saying you have a PnP OS to
satisfy Linux but this is going against what MS suggest (but will
probably work OK anyway).
When the BIOS configures a device different from what Windows has in
it's registry, Windows will tell you that it's finding new hardware.
What it's really doing is finding old hardware that has been
configured differently so it thinks it's new hardware. At any rate,
it records the configuration that the BIOS has used in its registry
and the device should work OK from now on.
[1m3.1.3. MS Windows 95, 98 (and Me ?)[0m
For Windows9x, MS suggest that you tell the BIOS that you have a PnP
OS (the exact opposite of the case for Windows 2000 and XP). This
should also be OK for Linux if you have kernel 2.4 or later. But if
you have a Linux kernel prior to 2.4 then it's best for Linux to say
that it's not a PnP OS. One way to resolve this dilemma is to set it
up for the OS you use more frequently. Then when you boot the other
OS, manually go into the BIOS and change the setting. This is a lot
of bother but it's feasible if you almost never use one the the OS's.
Otherwise there are better ways to resolved this dilemma.
The second way to resolve this dilemma is to get Linux to resource-
configure everything. See ``Linux prior to the 2.4 kernel''. Then
you tell the BIOS it's a PnP OS.
The third way to resolve this dilemma is to tell the BIOS it's not a
PnP OS. This is going against what MS says you should do, but it's
possible to get MS Windows9x to work OK if you understand what to do
(and why). If you tell the BIOS it's not a PnP OS, shouldn't MS
Windows detect how the BIOS has configured things and change it if it
doesn't like what the BIOS has done? It should, but unfortunately, it
doesn't seem to work this way.
What Windows9x seems to do when it finds hardware that is already
configured by the BIOS is to just leave it alone and not reconfigure
it. Now Windows9x keeps a record of the bus-resource configuration in
its registry. If the BIOS configuration is different, it should
either correct what's in its registry to conform to what the BIOS has
set or reconfigure everything per what's in the registry. Bad news.
It seems to do neither and thinks the actual configuration is the same
as in the registry when in fact it's different.
But if the registry happens to contain a bus-resource configuration
that is exactly the same as how the BIOS configures things, then
everything will obviously work OK. A device will thus work fine if
the BIOS has configured it the same as recorded in the registry. So
the way to get MS Windows to work OK is to get the registry in sync
with how the BIOS configures. As mentioned previously, the BIOS
configures things per its ESCD (which is something like the registry
for the BIOS). See ``The BIOS's ESCD Database''. So we need to get
the registry in sync with the BIOS's ESCD so that the registry and the
ESCD contain the same configuration. In some cases, these two just
happen to be in sync and you don't need to do anything.
One question you may think of is: how did the BIOS's ESCD and Windows
registry ever get out of sync in the first place? Here's one
scenario. You install Windows with the BIOS set to a PnP OS. Then
Windows configures most everything and saves that configuration in its
registry. Then later on you change the BIOS setting to not a PnP OS.
Then upon booting, the BIOS configures everything and it doesn't do it
exactly like Windows did it. Thus the actual configuration of the
hardware and what Windows has in its registry are now different.
One way to try to get the Registry and the ESCD the same is to install
(or reinstall) Windows when the BIOS is set for "not a PnP OS". This
should present Windows with hardware configured by the BIOS. If this
configuration is without conflicts, Windows will hopefully leave it
alone and save it in it's Registry. Then the ESCD and the registry
are in sync.
Another method is to remove devices that are causing problems in
Windows by clicking on "remove" in the Device Manager. Then reboot
with "Not a PnP OS" (set it in the BIOS's CMOS as you start to boot).
Windows will then reinstall the devices, hopefully using the bus-
resource settings as configured by the BIOS. Be warned that Windows
will likely ask you to insert the Window installation CD since it
sometimes can't find the driver files (and the like) even though they
are still there. A workaround for this is to select "skip file" which
will avoid installing the file from a CD. If the file is still on the
HD, then the driver will hopefully find it OK even though the Window's
install program requested you install it from a CD (which you skipped
doing).
As a test I "removed" a NIC card which used a Novell compatible
driver. Upon rebooting, Windows reinstalled it with Microsoft
Networking instead of Novell. This meant that the Novell Client
needed to be reinstalled --a lot of unnecessary work. So in a case
like this it may be better to not fib to Windows95/98 but instead to
get Linux to configure bus-resources.
When using a Window-Linux PC (dual boot) you might notice a change in
the way the BIOS configures due to Windows9x (and other versions of
Windows ??) modifying the ESCD. It supposedly does this only if you
"force" a configuration or install a legacy device. See ``Using
Windows to set ESCD''. Device drivers that do configuring may modify
what the BIOS has done as will the isapnp or PCI Utilities programs if
you run them.
[1m3.2. Assigning Resources by the BIOS[0m
Modern BIOSs allow you to manually allocate resources, primarily IRQs.
There is usually an option to set the an allocation to "auto" so that
the BIOS decides how to allocate the resource. "Auto" is often a good
choice unless you have old legacy non-pnp ISA cards.
If you have such non-PnP cards, then it may be important to reserve
resources (such as IRQ's) for these in the BIOS. Otherwise the BIOS
may use these resources for some other device and create conflicts.
An exception is that for some common legacy devices (such as parallel
and serial ports, disk drives), the BIOS may find them (look at the
screen at boot-time) so you don't need to reserve resources for them.
If you've used Windows on your PC, it might be true that Windows has
already told the BIOS about them by running the ICU utility (or the
like) under Windows.
For PCI, the BIOS may let you assign IRQs to card slots 1, 2, 3, 4,
etc. If you do this, you should know what card is in what slot.
Actually, each slot has 4 PCI IRQs: A, B, C, and D. If the BIOS menu
doesn't say which of these (A, B, C, D) is being assigned to an IRQ
number, it's likely that it's only assigning the IRQ number to PCI IRQ
A. But many PCI cards only use IRQ A so it's then just like assigning
an IRQ to a slot. See ``PCI Interrupts''
[1m3.3. Reset the configuration?[0m
This is a little risky to do. It will erase the BIOSs ESCD data-base
of how your PnP devices should be configured as well as the list of
how legacy (non-PnP) devices are configured. Never do this unless you
are convinced that this data-base is wrong and needs to be remade. It
was stated somewhere that you should do this only if you can't get
your computer to boot. If the BIOS loses the data on legacy ISA
devices, then you'll need to run ICA again under DOS/Windows to
reestablish this data.
[1m4. How to Deal with PnP Cards[0m
[1m4.1. Introduction to Dealing with PnP Devices[0m
Today almost all new internal boards (cards) are Plug-and-Play (PnP).
Thus, the configuring of bus-resources should, in almost all cases be
entirely automatic. If a device is not working, see if it was
detected, possibly by rebooting. If the device driver can't resource-
configure it, then hopefully one or more of methods 2-6 will:
1. ``Device Driver Configures''
2. ``/sys User Interface Configures'' kernel 2.6 + (not for PCI yet,
other severe limitations)
3. ``BIOS Configures'' (For the PCI bus you only need a PCI BIOS,
otherwise you need a PnP BIOS)
4. ``ISA cards only: Disable PnP'' by jumpers or DOS/Windows software
(but many cards can't do this)
5. ``ISA Bus: Isapnp'' is a program you can always use to configure
ISA PnP devices
6. ``PCI Utilities'' is for configuring the PCI bus but the device
driver should handle it
7. ``Windows Configures'' and then you boot Linux from within
Windows/DOS. Use as a last resort
Any of the above will set the bus-resources in the hardware but only
the first one (and possibly the second) tells the driver what has been
done. How the driver gets informed depends on the driver. You may
need to do something to inform it. See ``Tell the Driver the
Configuration''
[1m4.2. Device Driver Configures, Reserving Resources[0m
Device drivers (with the help of code provided by the kernel) can be
written to use PnP methods to set the bus-resources in the hardware
but only for the device that they control. But many device drivers
just accept what the BIOS or Linux has configured and use code
provided by the kernel to find out how this device has been
configured. Since the driver has checked the configuration and
possibly reconfigured it, it obviously knows the configuration and
there is no need for you to tell it this info. This is obviously the
easiest way to do it since you don't have to do anything if the driver
does it all.
If you have old pre-PnP ISA hardware, the Linux PnP software may not
know about it and the bus-resources it requires. So it might
erroneously allocate the resources that this old hardware needs to
some other device. The result is a resource conflict but there's a
way to try to avoid it. You can reserve the resources that the old
ISA card needs by configuring the BIOS at boot-time (usually), the
isa-pnp module or to the kernel (if the PnP is built into the kernel).
For example, to reserve irq 5 give this argument to the isa-pnp module
(or to the kernel): isapnp_reserve_irq=5. See BootPrompt-HOWTO.
Instead of ..._irq there are also _io, _dma, and _mem.
For PCI devices, most drivers will configure PnP. Unfortunately, a
driver could grab bus-resources that are needed by other devices (but
not yet allocated to them by the kernel). Thus a more sophisticated
PnP Linux kernel would be better, where the kernel did the allocation
after all requests were in. See ``How Linux Does PnP''.
[1m4.3. /sys User Interface Configures[0m
Starting with kernel 2.6 there's supposedly a new way for the user to
resource configure using the /sys directory tree. But as of Aug.
2004, it can't be used for configuring in most cases. See ``The /sys
Directory Tree''.
[1m4.4. BIOS Configures[0m
[1m4.4.1. Intro to Using the BIOS to Configure PnP[0m
If you have a PnP BIOS, it can configure the hardware. If the driver
can't do it, the BIOS probably can. This means that your BIOS reads
the resource requirements of all devices and configures them
(allocates bus-resources to them). It is a substitute for a PnP OS
except that the BIOS doesn't match up the drivers with their devices
nor tell the drivers how it has done the configuring. It should
normally use the configuration it has stored in its non-volatile
memory (ESCD). If it finds a new device or if there's a conflict, the
BIOS should make the necessary changes to the configuration and may
not use the same configuration as was in the ESCD. In this case it
should update the ESCD to reflect the new situation.
Your BIOS needs to support such configuring and there have been cases
where it doesn't do it correctly or completely. The BIOS may need to
be told via the CMOS menu that it's not a PnP OS. While many device
drivers will be able to automatically detect what the BIOS has done,
in some cases you may need to determine it (not always easy). See
``What Is My Current Configuration?'' A possible advantage to letting
the BIOS do it is that it does its work before Linux starts so it all
gets done early in the boot process.
Most BIOS made after about 1996 ?? can resource-configure both the PCI
and ISA buses. But it's been claimed that some older BIOSs can only
do the PCI. And of course, for PCs with only the PCI bus, the BIOS
only needs to do PCI. To try to find out more about your BIOS, look
on the Web. Please don't ask me as I don't have data on this. The
details of the BIOS that you would like to know about may be hard to
find (or not available). Some old BIOS's may have minimal PnP
capabilities and seemingly expect the operating system to do it right.
If this happens you'll either have to find another method or try to
set up the ESCD database if the BIOS has one. See the next section.
[1m4.4.2. The BIOS's ESCD Database[0m
The BIOS maintains a non-volatile database containing a PnP-
configuration that it will try to use (if you claim that it's not a
PnP OS). It's called the ESCD (Extended System Configuration Data).
Again, the provision of ESCD is optional but most PnP-BIOSs have it.
The ESCD not only stores the resource-configuration of PnP devices but
also stores configuration information of non-PnP devices (and marks
them as such) so as to avoid conflicts. The ESCD data is usually
saved on a chip and remains intact when the power is off, but
sometimes it's kept on a hard-drive??
The ESCD is intended to hold the last used configuration. But since
Linux can change how devices are configured (including the user using
isapnp or pci utilities) then the ESCD will not know about this and
will not save this configuration in the ESCD. A good PnP OS might
update the ESCD so you can use it later on for a non-PnP OS (like
standard Linux). MS Windows9x does this only in special cases. See
``Using Windows to set ESCD''. Starting with kernel 2.6, Linux is
capable of modifying the ESCD but it's not used yet (as of Aug. 2004).
To use what's set in ESCD be sure you've set "Not a PnP OS" or the
like in the BIOS's CMOS. Then each time the BIOS starts up (before
the Linux OS is loaded) it should configure things this way. If the
BIOS detects a new PnP card which is not in the ESCD, then it must
allocate bus-resources to the card and update the ESCD. It may even
have to change the bus-resources assigned to existing PnP cards and
modify the ESCD accordingly.
There's a program that you may use to view the contents of the ESCD.
It shows IRQs and IO addresses etc., but device names are missing
(only EISA device-ID numbers). It's at: Index of
/home/gunther.mayer/lsescd <http://home.t-
online.de/home/gunther.mayer/lsescd/>
If each device saved its last configuration in its hardware, hardware
configuring wouldn't be needed each time you start your PC. But it
doesn't work this way. So all the ESCD data needs to be kept correct
if you use the BIOS for PnP. There are some BIOSs that don't have an
ESCD but do have some non-volatile memory to store info regarding
which bus-resources have been reserved for use by non-PnP cards. Many
BIOSs have both.
[1m4.4.3. Using Windows to set the ESCD[0m
Eventually the Linux kernel may set the ESCD. Starting with kernel
2.6, a function in the new code could do it provided the kernel has
been compiled with PNPBIOS. But it currently sits in the code unused.
If the BIOS doesn't set up the ESCD the way you want it (or the way it
should be) then it would be nice to have a Linux utility to set the
ESCD. One may resort to attempting to use Windows for this (if you
have it on the same PC) to do this.
There are three ways to use Windows to try to set/modify the ESCD.
One way is to use the ICU utility designed for DOS or Windows 3.x. It
should also work OK for Windows 9x/2k ?? Another way is to set up
devices manually ("forced") under Windows 9x/2k so that Windows will
put this info into the ESCD when Windows is shut down normally. The
third way is only for legacy devices that are not plug-and-play. If
Windows knows about them and what bus-resources they use, then Windows
should put this info into the ESCD.
If PnP devices are configured automatically by Windows without the
user "forcing" it to change settings, then such settings probably will
not make it into the ESCD. Of course Windows may well decide on its
own to configure the same as what is set in the ESCD so they could
wind up being the same by coincidence.
Windows 9x are PnP operating systems and automatically PnP-configure
devices. They maintain their own PnP-database deep down in the
Registry (stored in binary Windows files). There is also a lot of
other configuration stuff in the Registry besides PnP-bus-resources.
There is both a current PnP resource configuration in memory and
another (perhaps about the same) stored on the hard disk. To look at
this in Windows98 or to force changes to it you use the Device
Manager.
In Windows98 there are 2 ways to get to the Device Manager: 1. My
Computer --> Control Panel --> System Properties --> Device Manager.
2. (right-click) My Computer --> Properties --> Device Manager. Then
in Device Manager you select a device (sometimes a multi-step process
if there are a few devices of the same class). Then click on
"Properties" and then on "Resources". To attempt to change the
resource configuration manually, uncheck "Use automatic settings" and
then click on "Change Settings". Now try to change the setting, but
it may not let you change it. If it does let you, you have "forced" a
change. A message should inform you that it's being forced. If you
want to keep the existing setting shown by Windows but make it
"forced" then you will have to force a change to something else and
then force it back to its original setting.
To see what has been "forced" under Windows98 look at the "forced
hardware" list: Start --> Programs --> Accessories --> System Tools
--> System Information --> Hardware Resources --> Forced Hardware.
When you "force" a change of bus-resources in Windows, it should put
your change into the ESCD (provided you exit Windows normally). From
the "System Information" window you may also inspect how IRQs and IO
ports have been allocated under Windows.
Even if Windows shows no conflict of bus-resources, there may be a
conflict under Linux. That's because Windows may assign bus-resources
differently than the ESCD does. In the the rare case where all
devices under Windows are either legacy devices or have been "forced",
then Windows and the ESCD configurations should be identical.
[1m4.4.4. Adding a New Device (under Linux or Windows)[0m
If you add a new PnP device and have the BIOS set to "not a PnP OS",
then the BIOS should automatically configure it and store the
configuration in ESCD. If it's a non-PnP legacy device (or one made
that way by jumpers, etc.) then here are a few options to handle it:
You may be able to tell the BIOS directly (via the CMOS setup menus)
that certain bus-resources it uses (such as IRQs) are reserved and are
not to be allocated by PnP. This does not put this info into the
ESCD. But there may be a BIOS menu selection as to whether or not to
have these CMOS choices override what may be in the ESCD in case of
conflict. Another method is to run ICU under DOS/Windows. Still
another is to install it manually under Windows 9x/2k and then make
sure its configuration is "forced" (see the previous section). If
it's "forced" Windows should update the ESCD when you shut down the
PC.
[1m4.5. ISA cards only: Disable PnP ?[0m
PCI devices are inherently PnP so it can't be disabled. But a few ISA
devices once had options for disabling PnP by jumpers or by running a
Windows program that comes with the device (jumperless configuration).
If the device driver can't configure it, this will avoid the possibly
complicated task of doing PnP configuring. Don't forget to tell the
BIOS that these bus-resources are reserved. But since Linux support
for PnP has improved, you usually don't want to disable PnP. Here's
some more arguments in favor of PnP:
1. If you have MS Windows on the same machine, then you may want to
allow PnP to configure devices differently under Windows from what
it does under Linux.
2. The range of selection for IRQ numbers (or port addresses) etc.
may be too limited unless you use PnP.
3. You might have a Linux device driver that uses PnP methods to
search for the device it controls.
4. If you need to change the configuration in the future, it may be
easier to do this if it's PnP (no setting of jumpers or running a
Dos/Windows program).
Once configured as non-PnP devices, they can't be configured by PnP
software or a PnP-BIOS (until you move jumpers and/or use the
Dos/Windows configuration software again).
[1m4.6. ISA Bus: Isapnp (part of isapnptools)[0m
The isapnp standalone program is only for PnP devices on the ISA bus
(non-PCI). It was much needed prior to the 2.4 kernels. After the
2.4 kernel, which provided functionality to allow drivers deal with
ISA PnP, the isapnp standalone program is less significant. Also, the
BIOS may configure ISA PnP satisfactory. But the isa-pnp module (or
the equivalent built into the kernel) is now very significant since
various ISA device drivers call on it to configure bus-resources.
Prior to kernel 2.6 it resulted a /proc/isapnp "file" which may be
used to manually configure (see isapnp.txt in the kernel
documentation).
In some cases Linux distributions have been set up to run isapnp
automatically at startup. It's still done in 2004 but it isn't really
needed if the device drivers work well. If you need to set it up
yourself much of the documentation for isapnp is difficult to
understand unless you know the basics of PnP. This HOWTO should help
you understand it as well the FAQ that comes with isapnp. Running the
Linux program "isapnp" at boot-time will configure such devices to the
resource values specified in /etc/isapnp.conf. Its possible to create
this configuration file automatically but you then should edit it
manually to choose between various options. Then to let the driver
know the resources, you often need to specify them as parameters to
the appropriate modules (drivers). This is done with configuration
files, often in the /etc directory. Look there for files named mod*,
etc. If the driver is built into the kernel, then they may sometimes
be given as a parameter to the kernel. See BootPrompt-HOWTO.
With isapnp there once was a problem where a device driver which is
built into the kernel may run too early before isapnp has set the
address, etc. in the hardware. This resulted in the device driver
not being able to find the device. The driver tries the right address
but the address hasn't been set yet in the hardware. Is this still a
problem ??
If your Linux distribution automatically installed isapnptools, isapnp
may already be running at startup. In this case, all you need to do
is to edit /etc/isapnp.conf per "man isapnp.conf". Note that this is
like manually configuring PnP since you make the decisions as to how
to configure as you edit the configuration file.
If the configuration file is wrong or doesn't exist, you can use the
program "pnpdump" to help create the configuration file. It almost
creates a configuration file for you but you must skillfully edit it a
little before using it. It contains some comments to help you edit
it. While the BIOS may also configure the ISA devices (if you've told
it that you don't have a PnP OS), isapnp will redo it.
The terminology used in the /etc/isapnp.conf file may seem odd at
first. For example for an I0 address of 0x3e8 you might see "(IO 0
(BASE 0x3e8))" instead. The "IO 0" means this is the first (0th) IO
address-range that this device uses. Another way to express all this
would be: "IO[0] = 0x3e8" but isapnp doesn't do it this way. "IO 1"
would mean that this is the second IO address range used by this
device, etc. "INT 0" has a similar meaning but for IRQs (interrupts).
A single card may contain several physical devices but the above
explanation was for just one of these devices.
[1m4.7. PCI Utilities[0m
The package PCI Utilities (= pciutils, sometimes called "pcitools"),
allows one to manually PnP-configure the PCI bus (with difficulty).
"lspci" or "scanpci" lists bus-resources while "setpci" sets resource
allocations in the hardware devices. It appears that setpci is mainly
intended for use in scripts and one needs to understand the details of
the PCI configuration registers in order to use it. That's a topic
not explained here nor in the manual page for setpci.
People have used this to configure PCI devices where the driver failed
to do it. An example is found in my Modem-HOWTO and Serial-HOWTO in
the subsection "PCI: Enabling a disabled port". However, enabling a
device is of no use unless you have a working driver for the device.
[1m4.8. Windows Configures[0m
This method uses MS Windows to configure and should be used only if
all else fails. If you have Windows9x (or 2k) on the same PC, then
just start Windows and let it configure PnP. Then start Linux from
Windows (or DOS) using, for example, loadlin.exe. But there may be a
problem with IRQs for PCI devices. As Windows shuts down (without any
messages) to make way for Linux, it may erase (zero) the IRQ which is
stored in one of the PCI device's configuration registers. Linux will
complain that it has found an IRQ of zero.
The above is reported to happen if you start Linux using a shortcut
(PIF file). But a workaround is reported where you still use the
shortcut PIF. A shortcut is something like a symbolic link in Linux
but it's more than that since it may be "configured". To start Linux
from DOS you create a batch file (script) which starts Linux. (The
program that starts Linux is in the package called "loadlin"). Then
create a PIF shortcut to that batch file and get to the "Properties"
dialog box for the shortcut. Select "Advanced" and then check "MS-DOS
mode" to get it to start in genuine MS-DOS.
Now here's the trick to prevent zeroing the PCI IRQs. Click "Specify
a new MS-DOS configuration". Then either accept the default
configuration presented to you or click on "Configuration" to change
it. Now when you start Linux by clicking on the shortcut, new
configuration files (Config.sys and Autoexec.bat) will be created per
your new configuration.
The old files are stored as "Config.wos and Autoexec.wos". After you
are done using Linux and shut down your PC then you'll need these
files again so that you can run DOS the next time you start your PC.
You need to ensure that the names get restored to *.sys and *.bat.
When you leave Windows/DOS to enter Linux, Windows is expecting that
when you are done using Linux you will return to Windows so that
Windows can automatically restore these files to their original names.
But this doesn't happen since when you exit Linux you shut down your
PC and don't get back to Windows. So how do you get these files
renamed? It's easy, just put commands into your "start-Linux" batch
file to rename these files to their *.bat and *.sys names. Put these
renaming commands into your batch file just before the line that loads
Linux.
Also it's reported that you should click on the "General" tab (of the
"Properties" dialog of your shortcut) and check "Read-only".
Otherwise Windows may reset the "Advanced Settings" to "Use current
MS-DOS configuration" and PCI IRQs get zeroed. Thus Windows erases
the IRQs when you use the current MS-DOS configuration but doesn't
erase when you use a new configuration (which may actually configure
things identical to the old configuration). Windows does not seem to
be very consistent.
[1m4.9. PnP Software/Documents[0m
· Isapnptools homepage <http://www.roestock.demon.co.uk/isapnptools/>
· Proposal for a Configuration Manager for Linux
<http://www.astarte.free-online.co.uk> 1999 (Never got into kernel
but Linux is slowly "evolving" in this direction).
· PnP Specs. from Microsoft
<http://www.microsoft.com/hwdev/tech/pnp/default.asp>
· Book: PCI System Architecture, 4th ed. by Tom Shanley +, MindShare
1999. Covers PnP-like features on the PCI bus.
· Book: Plug and Play System Architecture, by Tom Shanley, Mind Share
1999. Details of PnP on the ISA bus. Only a terse overview of PnP
on the PCI bus.
· Book: Programming Plug and Play, by James Kelsey, Sams 1995.
Details of programming to communicate with a PnP BIOS. Covers ISA,
PCI, and PCMCIA buses.
[1m5. Tell the Driver the Configuration ??[0m
[1m5.1. Introduction[0m
A modern driver for a device will find out the bus-resource
configuration without you having to tell it anything. It may even set
the bus-resources in the hardware using PnP methods. Some drivers
have more than one way to find out how their physical device is
configured. In the worst case you must hard-code the bus-resources
into the kernel (or a module) and recompile.
In the middle are cases such as where you run a program to give the
bus-resource info to the driver or put the info in a configuration
file. In some cases the driver may probe for the device at addresses
where it suspects the device resides (but it will never find a PnP
device if it hasn't been enabled by PnP methods). It may then try to
test various IRQs to see which one works. It may or may not
automatically do this.
In the modern case the driver should use PnP methods to find the
device and how the bus-resources have been set by the BIOS, etc. but
will not actually set them. It may also look at some of the "files"
in the /proc directory.
One may need to "manually" tell a driver what bus-resources it should
use. You give such bus-resources as a parameter to the kernel or to a
loadable module. If the driver is built into the kernel, you pass the
parameters to the kernel via the "boot-prompt". See The Boot-Prompt-
HOWTO which describes some of the bus-resource and other parameters.
Once you know what parameters to give to the kernel, one may put them
into a boot loader configuration file. For example, put append="...".
into the lilo.conf file and then use the lilo command to get this info
into the lilo kernel loader.
If the driver is loaded as a module, in many cases the module will
find the bus-resources needed and then set them in the device. In
other cases (mostly for older PCs) you may need to give bus-resources
as parameters to the module. Parameters to a module (including ones
that automatically load) may be specified in /etc/modules.conf. There
are usually tools used to modify this file which are distribution-
dependent. Comments in this file should help regarding how to modify
it. Also, any module your put in /etc/modules will get loaded along
with its parameters.
While there is much non-uniformity about how drivers find out about
bus-resources, the end goal is the same. If you're having problems
with a driver you may need to look at the driver documentation (check
the kernel documentation tree). Some brief examples of a few drivers
is presented in the following sections:
[1m5.2. Serial Port Driver Example[0m
For PCI serial ports (and for ISA PnP serial ports after 2.4 kernels)
the serial driver detects the type of serial port and PnP configures
it. Unfortunately, there may be some PCI serial ports that are not
supported yet.
For the standard ISA serial port with very old older versions of the
kernel and serial driver (not for multiport cards) the driver probes
two standard addresses for serial ports. It doesn't probe for IRQs
but it just assigns the "standard" IRQ to the first two serial ports.
This could be wrong.
For anything else the configuration file for the setserial program
must be manually modified. See Serial-HOWTO for more details. You
use setserial to inform the driver of the IO address and Setserial is
often run from a start-up file. In newer versions there is a
/etc/serial.conf file (or /var/lib/setserial/autoconfig that you
"edit" by simply using the setserial command in the normal way and
what you set using setserial is saved in the serial.conf configuration
file. The serial.conf file should be consulted when the setserial
command runs from a start-up file. Your distribution may or may not
set this up for you.
There are two different ways to use setserial depending on the options
you give it. One use is used to manually tell the driver the
configuration. The other use is to probe at a given address and
report if a serial port exists there. It can also probe this address
and try to detect what IRQ is used for this port.
Even with modern kernels, setserial is sometimes needed if the driver
fails to detect the serial port, or if you have very old hardware.
[1m6. How Do I Find Devices and How Are They Configured?[0m
[1m6.1. Finding and How-Configured Are Related[0m
Once you find your hardware, the same program that found it usually
tells you how it's configured. So finding out how it's configured is
usually the same procedure as finding the hardware.
[1m6.2. Devices May Have Two "Configurations"[0m
Here "configuration" means the assignment of PnP bus-resources
(addresses, IRQs, and DMAs). For each device, there are two parts to
the configuration question:
1. What does the driver think the hardware configuration is?
2. What configuration (if any) is actually set in the device hardware?
Each part should have the same answer (the same configuration).
The configuration of the device hardware and its driver should
obviously be the same (and usually is). But if things are not
working right, it could be because there's a difference. This
means the the driver has incorrect information about the actual
configuration of the hardware. This spells trouble. If the
software you use doesn't adequately tell you what's wrong (or
automatically configure it correctly) then you need to investigate
how your hardware devices and their drivers are configured. While
Linux device drivers should "tell all", in some cases it may not be
easy to determine what has been set in the hardware.
Another problem is that when you view configuration messages on the
screen you need to know whether the reported configuration is that of
the device driver, the device hardware, or both. If the device driver
has either set the configuration in the hardware or has otherwise
checked the hardware then the driver should have the correct
information.
But sometimes the driver has been provided incorrect resources by a
script, configuration file, by incorrect resource parameters given to
a module, or perhaps just hasn't been told what the resources are and
tries to use incorrect default resources. For example, one can uses
"setserial" to tell the serial port driver an incorrect resource
configuration and the driver accepts it without question. But the
serial port doesn't work right (if at all).
[1m6.3. Finding Hardware[0m
A common problem is that the software doesn't detect your device
and/or determine the right driver for it. For PnP devices, detecting
them is easy via PnP software except for the unusual case where the
hardware has been disabled. The BIOS can sometimes be set to disable
PnP devices or a jumper/switch on the physical device itself could
disable it. In such a cases, the hardware can't be detected at all
until you either reconfigure the BIOS or change a jumper/switch.
Since the PCI bus is inherently PnP, there are no hidden devices.
Even though PnP devices are easy to find by PnP methods, if the driver
doesn't use PnP methods but uses the old method of probing for them at
likely address, they may not be found. This is because that, until
the resources are set in a PnP device (by the BIOS or Linux), the
device may have no address at all, so probing at likely address yields
nothing. For the old ISA bus, some of the devices may be non-PnP and
thus the old probing methods may find them. So many drivers still
probe at likely address, in addition to using PnP methods (= PnP
probing which is sometimes also just called "probing").
Ways to Find Hardware Devices (and their configurations): (follow link
to more details)
· Check the BIOS to make sure they are not disabled
· Watch the ``Boot-time Messages'' on the screen
· Look in ``The /proc Directory Tree''
· ``Tools for Detecting and/or Configuring all Hardware'' lsdev,
hwinfo, discover, kudzu
· ``Tools for Detecting and/or Configuring One Type of Hardware''
· PCI: ``PCI Bus Inspection''
· ISA Bus: ``ISA Bus Introduction''
· ISA Bus: ``PnP cards''
· ISA Bus: For ``Non-PnP Cards''
· ISA Bus: For ``Cards with jumpers''
· ISA Bus: If ``Neither PnP nor jumpers''
· ``Use MS Windows''
[1m6.4. Boot-time Messages[0m
Significant info on the configuration may be obtained by reading the
messages from the BIOS and from Linux that appear on the screen when
you first start the computer. These messages often flash by too fast
to read but once they stop type Shift-PageUp a few times to scroll
back to them. To scroll forward thru them type Shift-PageDown.
Typing "dmesg" at any time to the shell prompt will show only the
Linux kernel messages and may miss some of the most important ones
(including ones from the BIOS). The messages from Linux may sometimes
only show what the device driver thinks the configuration is, perhaps
as told it via an incorrect configuration file. Checking log files in
/var/log may also be useful.
For the PCI bus, the notation: 00:1a:0 means the PCI bus 00 (the main
PCI bus), PCI card (or chip) 1a, and function 0 (the first device) on
the card or chip. The 2nd device on the card (or chip) 08 would be:
00:08:1.
The BIOS messages display first and will show the actual hardware
configuration at that time, but isapnp, or pci utilities, or device
drivers may change it later. In some cases it doesn't show devices
that the BIOS didn't configure.
If the BIOS messages don't show as you back up to the start of the
BIOS messages using Shift-PageUp, try freezing them as they flash by,
by hitting the "Pause" key as soon as the first words flash on the
screen. Press any key to resume. It's often tricky to hit Pause
exactly at the right time. Be sure to hold down the "Shift" key
before hitting "Pause" since "Pause" is a shifted key. If you miss,
hit Ctrl-Alt-Del when Linux starts booting to reboot and try again.
Once the messages from Linux start to appear, it's too late to use
"Pause" since it will not freeze the messages from Linux.
To set things in the BIOS such as IRQs reserved for legacy hardware,
serial port addresses, etc. you need to get into the BIOS (CMOS) setup
menus at boot time. Each BIOS brand has different keys you need to
hold down to do this. There are lists on the Internet. Sometimes by
freezing the BIOS messages or watching the screen, the key you need to
press will be indicated in a message such as "Press DEL for setup".
But it may flash by so fast that you miss it. Of course, you don't
set stuff in the BIOS that you don't understand, or your PC may become
disabled.
Messages from the BIOS at boot-time tell you how the hardware
configuration was then. The current configuration may still be the
same since Linux should hopefully accept what the BIOS has done if
it's OK. Messages from Linux may be from drivers that used kernel PnP
functions to inspect and/or set bus-resources. These should be
correct, but beware of messages that only show what the driver was
told from a configuration file. It could be wrong. Of course, if the
device works fine, then it's likely configured the same as the driver.
[1m6.5. The /proc Directory Tree[0m
Starting with Kernel 2.6, in addition to the /proc directory tree,
there's also a /sys or /directory tree See ``The /sys Directory
Tree''. These trees are useful for finding resource configurations
and devices. The "files" in them represent data in the kernel memory
and don't exist at all on you harddrive. Programs such as lspci get
their info from the /proc tree so such programs should display the
results in more readable form than directly inspecting the "files" in
/proc.
/proc/ioports shows the I/O addresses that the active drivers use. If
there's a mistake (wrong address) it means trouble. Many interrupts
that have been allocated to drivers don't show here at all since
they're not currently being used. For example, even though your
floppy drive has a floppy disk in it and it's ready to use, the
interrupt for it will not show unless its in use. Again, just because
an interrupt shows up here doesn't mean that it always exists in the
hardware. A clue that it doesn't exist in hardware will be if it
shows that no interrupts have been issued by this interrupt. Even if
it shows a few interrupts have been issued, there is no guarantee that
they came from the device shown. It could be that some other device
which is not currently in use has issued them. A device not in use
(per the kernel) may have issued some interrupts.
/proc/interrupts shows only interrupts currently in use. Many
interrupts that have been allocated to drivers don't show here at all
since they're not currently being used. For example, even though your
floppy drive has a floppy disk in it and it's ready to use, the
interrupt for it will not show unless its in use. Again, just because
an interrupt shows up here doesn't mean that it always exists in the
hardware. A clue that it doesn't exist in hardware will be if it
shows that no interrupts have been issued by this interrupt. Even if
it shows a few interrupts have been issued, there is no guarantee that
they came from the device shown. It could be that some other device
which is not currently in use has issued them. A device not in use
(per the kernel) may have issued some interrupts.
/proc/bus/ has subdirectories (subfolders) /input/, /pci/, and
/isapnp/. The format of most of the files in this directory is very
cryptic, often just a copy of the bytes in the configuration space.
So, use them only as a last resort. The input/ subdirectory has
information on input devices such as the keyboard and mouse. It's not
as cryptic as the other directories under /proc/bus/ and might yield
some useful information about input devices that are PS2 or on the LPC
bus (See ``LPC Bus''). In /pci/00/ find one binary file for each pci
device where the file names are the pci-slot-numbers (also called pci-
slot-names). The 00 means pci bus 0.
[1m6.6. The /sys Directory Tree[0m
Starting with kernel 2.6 there's a new /sys directory for PnP
configuration. It's a sysfs type of file system and it's something
like the /proc filesystem since the "files" represent information in
the kernel memory and are not on your harddrive. But it's not as
useful as the /proc filesystem. Originally (in the 2.5 kernels) it
was called "driver file system" of type "driverfs".
In the sysfs, each device which exists on your system has it's own
directory which contains files showing the resources allocated to it.
Such device directories have names like 0000:00:12.0@ or 00:06@. What
devices are these? The first is a PCI card in "slot" 12 of your PC.
The slot may actually be labeled PCI2 inside your PC (2 instead of
12). That's because low numbered "slots" are used for built-in
devices on the motherboard that don't use any physical slots. In this
example, "slots" 1-10 would be built-in and actual slots 11-14 are
labeled 1-4. By typing "lspci" you'll be able to match the numbers
(like 0000:00:12.0) to names (like IDE interface). Type "lspci -v" or
"lspci -vv" to see more.
Well then, what is 00:06 ? It's an ISA card (or built-in device) but
it's not ISA slot 6 (like the PCI numbering). When a search was made
for ISA-PNP devices, it was the 6th one found. More precisely, it was
the 7th one found since there's a device numbered: 00:00. So how does
one identify them? Well, you could type: "cat */*" and display all
the files for all the devices, but even then you don't see the device
names (but do see info from which you can identify them). This
inconvenience will hopefully be fixed in the future.
Not only do these files supply information on the bus-resource
configuration (in somewhat cryptic format) and drivers (in "driver"
directories), but in the future, you should be able to use them to
change the resource configuration. Right now (Aug 2004) you can't
configure the PCI bus with it. A serious limitation is that per the
present "driver model" you can't change the resource of a device that
has been assigned to a driver which likely means that you'll need to
unload the driver module in order to use it. If the driver is built
in, there's no hope. These serious limitations will hopefully be
eliminated in the future. In the kernel documentation is a file:
"pnp.txt" telling how to configure. As of Aug. 2004, it was much out-
of-date but the author is working on an update. Using the /sys tree
to configure resources is known as the "Linux Plug and Play User
Interface".
The other part of "Linux Plug and Play" is the kernel interface used
by device drivers. This has changed a lot starting with kernel 2.6
but most drivers are still using the old interface (as of Aug. 2004).
It's possible also for drivers (or you) to use the "user interface"
which needs improvement.
[1m6.7. PCI Bus Inspection[0m
It's easy to find out what bus-resources have been assigned to devices
on the PCI bus with the "lspci" and/or "scanpci" commands The options
-v or -vv will show more detail. In some cases, "scanpci" will find a
device that "lspci" can't find. That's because "scanpci" directly
searches for devices on the pci bus (via the configuration space) and
doesn't use data obtained by the kernel (where it could be wrong due
to a kernel bug --I've just found such a case).
This info in more cryptic format is found in "files" located in the
/sys and /proc trees. In /sys/bus/pci/devices the file vendor will
contain the vendor id number such as 0x4B8C, etc. In still more
cryptic format it's in /proc/bus/pci. Such information in older
kernels prior to kernel 2.6, was in /proc/pci (non-cryptic but IRQs in
hexadecimal) or in /proc/buspci/devices (cryptic display).
In most cases, for PCI you will only see how the hardware is now
configured and not what resources are required. In some cases you
only see the base addresses (the starting addresses of the range) but
not the ending addresses. If you see the entire range then you can
determine how many bytes of address resources are needed.
[1m6.8. ISA Bus Introduction[0m
For cards on the ISA bus, it's not as simple as for the PCI bus which
is inherently PnP. Newer ISA cards are PnP but older ones are not.
Also, some cards that are PnP have had their PnP disabled by special
software which runs only on MS. The non PnP cards are configured by
jumpers on the card or by MS software.
[1m6.9. ISA PnP cards[0m
If it's a PnP card you may try running pnpdump --dumpregs but it's not
a sure thing. The results may be seem cryptic but they can be
deciphered. Don't confuse the read-port address which pnpdump uses
for communication with PnP cards with the I/O address of the found
device. They are not the same.
[1m6.10. LPC Bus[0m
LPC (Low Pin Count) is a bus-like interface often used on laptops and
increasingly used on desktops too. To find out if you have LPC type
"lspci" and look for "LPC". There are other words next to "LPC" such
as "ISA Bridge ... LPC Interface Controller" or "LPC Bridge", etc.
LPC is not really ISA but it substitutes for an ISA bus.
The old ISA bus was slow and has generally been replaced by the fast
PCI bus. But for slow devices, there's no need for a large and fast
PCI bus. Thus a small LPC interface was created to be used for slow
"legacy" devices such as serial ports, parallel ports, and floppy
drives. It is only 4 bits (half-byte) wide as compared to 32 or 64
bits for the PCI bus. This 4-bit path is shared, and used for data,
addresses, and control (it's multiplexed). So it's clear why LPC
stands for "Low Pin Count" and why it saves space on motherboards
(especially important in laptops). Since LPC operates at about 4
times the clock speed of the old ISA bus its bandwidth is no worse
than ISA.
So a computer using LPC will have all fast devices on the PCI bus,
etc. and slow (legacy) devices on the LPC bus interface. All LPC
devices will be on-board; there are no LPC slots. Unfortunately,
while LPC is Plug-and-Play, it has no standards for Plug-and-Play like
PCI and ISA do. So each brand of motherboard may do it somewhat
differently. The specs suggests that it be done via ACPI. Devices on
this bus sometimes use isapnp. So if Linux can't configure resources
on it, you hope that the BIOS can. It may help if you tell the BIOS
it's a non-PnP OS ?? Linux support for LPC as of late 2004 was very
much incomplete but Linux has some support for the configuring aspects
of ACPI.
A major chip on the LPC bus is the superio chip which contains legacy
IO devices: serial and parallel ports, floppy controller, keyboard
controller, etc. BIOS data may also reside on the LPC bus.
[1m6.11. Non-PnP Cards[0m
In contrast to PnP cards, non-PnP cards always have their resources
set in the hardware. That is they always have an address and IRQ
unless there is a jumper setting, etc. for disabling the device.
Sometimes the resources used can be found by probing done by the
device driver or by other software that does probing. For example
"scanport" (Debian only ??) probes most IO port address and may find
ISA devices. But be warned that it might hang your PC. Sometimes it
will fail to find hardware that's actually there (since the hardware
has the default 0xff in it's registers). Even if It finds the
hardware it will not show the IRQ nor will it positively identify the
hardware.
So one way to try to find such hardware is to start a driver, which
may probe for such hardware. By looking at the boot-time messages,
you might see a driver start and find the hardware. Otherwise, you
may need to find a driver and start it (for example, by having it load
as a module).
Finding the right driver may be difficult. Sometimes there just isn't
any driver since some devices aren't (yet ?) supported by Linux. To
determine which driver you need, look at any documentation which might
identify the card. If this fails, look on the card itself, including
important names/numbers on the chips. But the identification of the
driver module you need may not be anywhere on the card. You could
find the FCC id on the card and then search the Internet with the FCC
id number to try to find more information about the card (or the chips
on it).
[1m6.12. Non-PnP Cards with jumpers[0m
If the card has jumpers to set the resources (configuration) then one
may look at how the jumpers are set. There are some cards that had
both PnP and jumpers. They worked like jumper cards if PnP was
somehow disabled. Sometimes a card has labels on it showing how to
set the jumpers (or at least gives some clue). You may need the
documentation that came with the card (either printed or on a floppy
disk). Perhaps you can find it on the Internet.
[1m6.13. Neither PnP nor jumpers[0m
One the most difficult cases is where software running under MS has
been used to configure either a non-PnP card or a PnP card where PnP
has been disabled by the same MS software. So you can't configure it
by PnP nor by jumpers. In this case your only hope is to probe for
addresses as described in ``Non-PnP Cards''. Or try to find the MS
software that configured it.
[1m6.14. Tools for Detecting and/or Configuring all Hardware[0m
In a duplication of effort, various major distributions of Linux
developed their own tools for detection and/or configuration of
hardware. This configuring usually a lot more than just the resource
type configuring of Plug-and-Play. It's configuring in general which
is mostly beyond the scope of this howto.
Then other distributions, such as Debian, might obtain copies of the
tool and offer it to their users as an option, or as a troubleshooting
tool. These tools likely make use of the standard Linux tools for
detecting hardware such as "lspci". In the following list of tools,
the name of the distribution that developed it is in parentheses, but
the tool is likely available also in other distributions.
· hwinfo (SuSE) detects move stuff than discover
· discover (Progeny, used by Debian)
· Kudzu (RedHat) detects and configures
· lsdev (standard Linux command)
· hwsetup-knoppix (Knoppix, based on Kudzu)
[1m6.15. Tool for Detecting and Configuring One Type of Hardware[0m
There are various tools available to find and possibly configure
various type of devices. This configuring is configuring in general
which is not covered by this howto. But since finding devices is part
of this howto, here's a list of some of these programs:
· read-edid (get-edid): gets parameters of VESA monitors (except very
old ones)
· sndconfig: for soundcards
· printtool: printers, must have X-window running
· pconf-detect: parallel ports
· mdetect: detects and configures mice (but couldn't find mine).
Does it know about the mice devices in /dev/input/?
· nictools-pci (and nictools-nopci) for ethernet cards
· hdparm: configure hard drive hardware
· hotplug: used by kernel
[1m6.16. Use MS Windows[0m
Some people have attempted to use Windows to see how bus-resources
have been set up. Unfortunately, since PnP hardware forgets its bus-
resource configuration when powered down, the configuration may not be
the same under Linux. For non PnP hardware (or where someone has
disabled PnP inside the device by jumpers or Windows software), then
using Windows should work OK. Even for PnP, it often turns out to be
the same because in many cases both Windows and Linux simply accept
what the BIOS has set. But where Windows and/or Linux do the
configuring, they may do it differently. So don't count on PnP
devices being configured the same.
[1m7. PnP for External and Plug-in Devices[0m
[1m7.1. USB Bus[0m
The USB (Universal Serial Bus) is a high speed bus on an external
cable that plugs into a PC. The external bus cable has its own
communication protocols and doesn't use any IRQs, I/0 addresses (or
other bus-resources). Communication is by packets, something like the
Internet, only there are time-slice allocations which prevent any one
device from hogging the bus if other devices need it. There are free
time slots which allow every device to send a short message to the bus
controller without any need for IRQs on the bus.
However, the USB bus controller inside the PC does have an IRQ and an
address on the PCI bus (or ISA) which are used for communication
between the CPU and all devices on the USB. Thus there's no resource
allocations needed for the individual devices on the USB. One could
also think of this as all devices on the USB sharing the one interrupt
and address. If a device is on the USB it needs a driver that
understands the USB.
But each device on the USB does have an IDs, just like cards do on the
PCI bus. So Linux likely maintains a table of these IDs so that
device drivers can check them to find their device. The USB also
support "hot plug". To find out what is on the USB bus, you could use
a general hardware detection tool like "discover" or "hwinfo".
[1m7.2. Hot Plug[0m
"Hot plug" is where you plug something into a PC (usually via a cable
connection) and it is instantly detected. If required, it is
configured with bus-resources. The driver for it is also started,
perhaps by loading a module for it. For this to work the hardware
used must be designed for hot plugging. One can hot plug certain PCI
cards (Cardbus), USB devices, and IEEE 1394 devices (Firewire).
When a new device is detected, it's registers are read so as to get
the ID number of the device. Then to find a driver, Linux must
maintain a table mapping ID numbers to drivers. It wasn't until
kernel 2.4 that such a table existed since Linux once shunned
centralized PnP. It's named: MODULE_DEVICE_TABLE.
[1m7.3. Hot Swap[0m
"Hot Swap" is where you remove an old device and then plug in a new
device to replace the old one. You have thus "swapped" devices. Now
in addition to being able to detect that a new device has been plugged
in, the removal of the old device needs to be detected too.
[1m7.4. PnP Finds Devices Plugged Into Serial Ports[0m
External devices that connect to the serial port via a cable (such as
external modems) can also be called Plug-and-Play. Since only the
serial port itself needs bus-resources (an IRQ and I/O address) there
are no bus-resources to allocate to such plug-in devices. In this
case, PnP is used only to identify the modem (read it's model code
number). This could be important if the modem is a software modem
(linmodem) and requires a special driver. There is a special PnP
specification for such external serial devices (something connected to
the serial port).
Linux doesn't support this yet ?? For a hardware modem, the ordinary
serial driver will work OK so there's little need for using the
special serial PnP to find a driver. You still need to tell the
communications program what port (such as /dev/ttyS1) the modem is on.
With PnP you wouldn't need to even do this. With the advent of
software modems that have Linux drivers (linmodems), it would be nice
to have the appropriate driver install itself automatically via PnP.
[1m8. Error Messages[0m
[1m8.1. Unexpected Interrupt[0m
This means that an interrupt happened that no driver expected. It's
unlikely that the hardware issued an interrupt by mistake. It's more
likely that the software has a minor bug and doesn't realize that some
software did something to cause the interrupt. In many cases you can
safely ignore this error message, especially if it only happens once
or twice at boot-time. For boot-time messages, look at the messages
which are nearby for a clue as to what is going on. For example, if
probing is going on, perhaps a probe for a physical device caused that
device to issue an interrupt that the driver didn't expect. Perhaps
the driver wasn't listening for the correct IRQ number.
[1m8.2. Plug and Play Configuration Error (Dell BIOS)[0m
The BIOS was unable to configure bus-resource. There may be an
interrupt conflict which can't be avoided. Dell suggests that you
remove some of your non-essential cards and see if it goes away. In
one case this problem was due to a defective motherboard.
[1m8.3. isapnp: Write Data Register 0xa79 already used (from logs)[0m
If you use isa-pnp, the IO address 0xa79 must not ever be used by any
device. So if other hardware is using 0xa79 when you try to load the
isa-pnp module, you'll get this message in your logs and the isa-pnp
will exit. One way to try to fix this is to load the isa-pnp module
early before other hardware is initialized. For PCMCIA this means to
load isa-pnp before running cb modules and service.
[1m8.4. Can't allocate region (PCI)[0m
Here "region" means address range. A PCI device that needs two
addresses will have region 0 for the first address and region 1 for
the second address needed. Use the command: lspci -vv to see the
various resource regions (often just called regions) and whether the
address is of type IO or memory. In PCI jargon region 2 is "base
address 2" (or "base address register 2"), etc.
[1m9. Interrupt Conflicts[0m
If an ISA device uses the same interrupt (IRQ) as some other device
(either ISA or PCI) there is usually an interrupt conflict. So if you
have no ISA devices, you shouldn't have any interrupt conflicts and
don't need to read this.
Another case of interrupt "conflict" happens when a device is
activated but can't be assigned an interrupt (IRQ) since none are
available. This is sort of an interrupt (IRQ) conflict since if an
interrupt were assigned, it would create a conflict. This can also
happen even if an interrupt is available, but it can't be used since
the hardware of the device that needs the interrupt doesn't support
the interrupt number available (or the motherboard doesn't support it
due to "routing" problems, see ``PCI Interrupts''). If the ISA
devices use up all the interrupts, then one or more PCI cards may be
in conflict since they can't get any IRQs.
Normally, the BIOS will assign interrupts and will not create
conflicts. But it may be forced to create conflicts if it runs out of
IRQs. This can happen if someone has set up the BIOS to reserve
certain IRQs for legacy ISA devices that are not PnP. These settings
may be wrong and should be checked out, especially if you're having
problems. For example, someone may have reserved an IRQ for an ISA
card that has long since been removed from the PC. If you unreserved
this IRQ then this IRQ is available and and conflict disappears.
Sometimes the BIOS will solve the problem of an IRQ shortage by using
IRQ 0. There is no such IRQ, but IRQ 0 means that the driver should
use polling instead of IRQs. This means that the driver frequently
checks the device (polls it) to see if the device needs servicing by
the interrupt service routine. Of course, this wastes computer time
and there's more likelihood of a buffer overrun inside a device since
it might not get serviced by the driver promptly enough.
A few ISA devices have been designed to permit interrupt conflicts
(between two ISA devices ??) but both ISA devices must be designed
this way and be driven by software that knows about sharing
interrupts. The motherboard must support it too.
[1m10. Appendix[0m
[1m10.1. Universal Plug and Play (UPnP)[0m
This is actually a sort of network plug-and-play developed by
Microsoft but usable by Linux. You plug something into a network and
that something doesn't need to be configured provided it will only
communicate with other UPnP enabled devices on the network. Here
"configure" is used in the broad sense and doesn't mean just
configuring bus-resources. One objective is to allow people who know
little about networks or configuring to install routers, gateways,
network printers, etc. A major use for UPnP would be in wireless
networking.
UPnP uses:
· Simple Service Discovery Protocol to find devices
· General Event Notification Architecture
· Simple Object Access Protocol for controlling devices
This HOWTO doesn't cover UPnP. UPnP for Linux is supported by Intel
which has developed software for it. There are other programs which
do about the same thing as UPnP. A comparison of some of them is at
<http://www.cs.umbc.edu/~dchakr1/papers/mcommerce.html> A UPnP project
for Linux is at SourceForge: UPnP SDK for Linux
<http://sourceforge.net/projects/upnp/>
[1m10.2. Address Details[0m
There are three types of addresses: main memory addresses, I/O
addresses (ports) and configuration addresses. On the PCI bus,
configuration addresses constitute a separate address space just like
I/O addresses do. Except for the complicated case of ISA
configuration addresses, whether or not an address on the bus is a
memory address, I/O address, or configuration address depends only on
the voltage on other wires (traces) of the bus. For the ISA
configuration addresses see ``ISA Bus Configuration Addresses (Read-
Port etc.)'' for details
[1m10.2.1. Address ranges[0m
The term "address" is sometimes used in this document to mean a
contiguous range of addresses. Addresses are in units of bytes, So
for example, a serial port at I/O address range 3F8-3FF will often
just be referred to by its base address, 3F8. The 3F8 is the location
of the first byte in the range (address range). To see the address
ranges for various devices, look at /proc/iomem and /proc/ioports.
[1m10.2.2. Address space[0m
To access both I/O and (main) memory address "spaces" the same address
bus is used (the wires used for the address are shared). How does the
device know whether or not an address which appears on the address bus
is a memory address or I/O address? Well, for ISA (for PCI read this
too), there are 4 dedicated wires on the bus that convey this sort of
information. If a certain one of these 4 wires is asserted, it says
that the CPU wants to read from an I/O address, and the main memory
ignores the address on the bus. In all, read and write wires exist
for both main memory and I/O addresses (4 wires in all).
For the PCI bus it's the same basic idea (also using 4 wires) but it's
done a little differently. Instead of only one of the four wires
being asserted, a binary number is put on the wires (16 different
possibilities). Thus, more info may be conveyed by these 4 wires..
Four of these 16 numbers serve the I/O and memory spaces as in the
above paragraph. In addition there is also configuration address
space which uses up two more numbers. This leaves 10 more numbers
left over for other purposes.
[1m10.2.3. PCI Configuration Address Space[0m
This is different from the IO and memory address spaces because
configuration address space is "geographic". Each slot for a card has
the slot number as part of the address. This way, Linux (or the BIOS)
can address a certain slot and find out what type of card is in that
slot. Each device has 64 standard byte-size registers and some of
these hold numbers which can unambiguously identify the device. Since
the number of slots is limited as are the number of PCI devices built
into motherboard, Linux (or the BIOS) only needs to check a limited
number of addresses to find all the PCI devices. If it reads all ones
(0xFF in hexadecimal) from the first register of a device, then that
means that no device is present. Since there is no card or device to
supply all these ones (0xFF) number, the PCI "host bridge" on the
motherboard supplies (spoofs) this number for all non-existent device.
The PCI slot number is called (in PCI lingo) the "Device Number" and
since a card may have up to 8 devices on it, a "Function Number" from
0-7 identifies which device it is on a PCI card. These numbers are
part of the geographic address. Linux programmers call it "pci-slot-
name". Thus what Linux calls a "device" is actually a "function" in
PCI lingo. The PCI bus number (often 00) also becomes part of the
geographic address. For example, 0000:00:0d.2 is PCI bus 0, slot 0d,
function 2. For the full geographic address, one must include the
double-word number of the device's configuration registers which one
wants to access. The leading 0000 (in 1999) were reserved for future
use.
How does the CPU designate that a read or write is to a PCI
configuration space? It doesn't, at least not directly. Instead when
access to configuration space is desired it does a 32-bit (double-
word) write to 0cf8-0cfb in I0 space and writes the full geographic
address there. The PCI host bridge is listening at this address and
insures that any next write of data to 0cfc-0cff is put into the
specified configuration registers of the specified device. The bridge
does this both by sending a special signal to the specified PCI card
(or the like) on a dedicated wire that goes only to the slot where the
card is plugged in. It also puts bits on the control bus saying that
what's on the address bus now is a geographic configuration space
address.
Why not make it simple and just have the CPU put bits on the control
bus to say that the address on the main bus is a geographic one for
PCI configuration? Well, most CPU's are not capable of doing this so
the PCI host bridge gets to do it instead.
[1m10.2.4. Range Check (ISA Testing for IO Address Conflicts)[0m
On the ISA bus, there's a method built into each PnP card for checking
that there are no other cards that use the same I/O address. If two
or more cards use the same IO address, neither card is likely to work
right (if at all). Good PnP software should assign bus-resources so
as to avoid this conflict, but even in this case a legacy card might
be lurking somewhere with the same address.
The test works by a card putting a known test number in its own IO
registers. Then the PnP software reads it and verifies that what it
reads is the same as the known test number. If not, something is
wrong (such as another card with the same address). It repeats the
same test with another test number. Since it actually checks the
range of IO addresses assigned to the card, it's called a "range
check". It could be better called an address-conflict test. If there
is an address conflict you get an error message.
[1m10.2.5. Communicating Directly via Memory[0m
Traditionally, most I/O devices used only I/O memory to communicate
with the CPU. The device driver, running on the CPU would read and
write data to/from the I/O address space and main memory.
Unfortunately, this requires two steps. For example, 1. read data
from a device (in IO address space) and temporarily store in in the
CPU; 2. write this data to main memory. A faster way would be for
the device itself to put the data directly into main memory. One way
to do this is by using ISA ``DMA Channels'' or PCI bus mastering.
Another way is for the physical device to actually contain some main
memory (at high addresses so as not to conflict with main memory chip
addresses). This way the device reads and writes directly to it's
self-contained main memory without having to bother with DMA or bus
mastering. Such a device may also use IO addresses.
[1m10.3. ISA Bus Configuration Addresses (Read-Port etc.)[0m
These addresses are also known as the "Auto-configuration Ports". For
the ISA bus, there is technically no configuration address space, but
there is a special way for the CPU to access PnP configuration
registers on the PnP cards. For this purpose 3 @ I/O addresses are
allocated and each addresses only a single byte (there is no "range").
This is not 3 addresses for each card but 3 addresses shared by all
ISA-PnP cards.
These 3 addresses are named read-port, write-port, and address-port.
Each port is just one byte in size. Each PnP card has many
configuration registers so that just 3 addresses are not even
sufficient for the configuration registers on a single card. To solve
this problem, each card is assigned a card number (handle) using a
technique called "isolation". See ``ISA Isolation'' for the complex
details.
Then to configure a certain card, its card number (handle) is sent out
via the write-port address to tell that card that it is to listen at
its address port. All other cards note that this isn't their card
number and thus don't listen. Then the address of a configuration
register (for that card) is sent to the address-port (for all cards
--but only one is listening). Next, data transfer takes place with
that configuration register on that card by either doing a read on the
read-port or a write on the write-port.
The write-port is always at A79 and the address-port is always at 279
(hex). The read-port is not fixed but is set by the configuration
software at some address (in the range 203-3FF) that will hopefully
not conflict with any other ISA card. If there is a conflict, it will
change the address. All PnP cards get "programmed" with this address.
Thus if you use say isapnp to set or check configuration data it must
determine this read-port address.
[1m10.4. Interrupts --Details[0m
[1m10.4.1. DMA[0m
Before going into interrupt details, there is another way for some
devices to initiate communication besides sending out an interrupt.
This method is a DMA (Direct Memory Access) request to take control of
the computer from the CPU for a limited amount of time. On the PCI
bus, it uses no "resources". Not all devices are capable of doing
DMA. See ``DMA Channels''.
[1m10.4.2. Soft interrupts[0m
There's also another type of interrupt known as a "soft interrupt"
which is not covered in this HOWTO and doesn't use any "resources".
While a hardware interrupt is generated by hardware, a soft interrupt
is initiated by software. There are a couple of ways to do this. One
way is for software to tell the CPU to issue an interrupt (an
interrupt instruction). Another way is for the software to send
messages to other processes so as to interrupt them although it's not
clear that this should be called an interrupt. The ksoftirq process,
which you may find running on a Linux PC, is a program which does this
kind of interrupt for dealing with device drivers. The device driver
starts running due to a hardware interrupt but later on, software
interrupts are used for the "bottom half" of the driver's interrupt
service routine. Thus, the ksoftirq process is also known as "bottom-
half". For more details see the kernel documentation.
[1m10.4.3. Hardware interrupts[0m
Interrupts convey a lot of information but only indirectly. The
interrupt request signal (a voltage on a wire) just tells a chip
called the interrupt controller that a certain device needs attention.
The interrupt controller then signals the CPU. The CPU then
interrupts whatever it was doing, finds the driver for this device and
runs a part of it known as an "interrupt service routine" (or
"interrupt handler"). This "routine" tries to find out what has
happened and then deals with the problem. For example, bytes may need
to be transferred from/to the device. This program (routine) can
easily find out what has happened since the device has registers at
addresses known to the the driver software (provided the IRQ number
and the I/O address of the device has been set correctly). These
registers contain status information about the device . The software
reads the contents of these registers and by inspecting the contents,
finds out what happened and takes appropriate action.
Thus each device driver needs to know what interrupt number (IRQ) to
listen to. On the PCI bus (and for some special cases on the ISA bus)
it's possible for two (or more) devices to share the same IRQ number.
Note that you can't share a PCI interrupt with an ISA interrupt (are
there any exceptions ??). When a shared interrupt is issued, the CPU
runs all interrupt service routines sequentially for all devices using
that interrupt. The first thing the first service routine does is to
check its device registers to see if an interrupt actually happened
for its device. If it finds that its device didn't issue an interrupt
(a false alarm) it likely will immediately exit and the service
routine begins for the second device using that same interrupt, etc,
etc. So the whole service routine doesn't need to run for each
device.
The putting of a voltage on the IRQ line is only a request that the
CPU be interrupted so it can run a device driver. In almost all cases
the CPU is interrupted per the request. But interrupts may be
temporarily disabled or prioritized so that in rare cases the actual
interrupt doesn't happen (or gets delayed). Thus what was above
called an "interrupt" is more precisely only an interrupt request and
explains why IRQ stands for Interrupt ReQuest.
[1m10.5. PCI Interrupts[0m
There are two newer developments in PCI interrupts that are not
covered here. They are especially important for cases of more than
one CPU per computer. One is the Advanced Programmable Interrupt
Controller (APIC). See the file "IO-APIC" in the i386 directory of
the kernel documentation. Don't confuse APIC with ACPI (Advanced
Configuration and Power Interface) which isn't covered in this HOWTO.
Another new development is Message Signalled Interrupts (MSI) where
the interrupt is just a message sent to a special address over the
main computer bus (no interrupt lines needed). But the device that
sends such a message must first gain control of the main bus so that
it can send the interrupt message. Such a message contains more info
than just "I'm sending an interrupt".
Ordinary PCI interrupts are different than ISA interrupts, but since
they are normally mapped to IRQs they behave in about the same way.
One major difference is that the BIOS does this mapping. Under Linux
it's not feasible to change it ?? unless the CMOS menu will let you do
it. But if you have the advanced APIC then there's a way to specify
it.
Another major difference is that PCI interrupts may be shared with two
exceptions: 1. very old PCI hardware (before 1995 ??) 2. defective PCI
hardware which may have a factory defect (it was made that way).
Normally, for example, IRQ5 may be shared between two PCI devices.
This sharing ability is built into the hardware and all device drivers
are supposed to support it. Note that you can't share the same
interrupt between the PCI and ISA bus. However, illegal sharing will
work provided only one of the two conflicting devices is in use at any
given time. "In use" here means that a program has "opened" the
device (and hasn't "closed" it) in its C programming code, even though
such a program could be temporarily sleeping, etc.
Here are some of the details of the PCI interrupt system. Each PCI
card (and device mounted on the motherboard) has 4 possible
interrupts: INTA#, INTB#, INTC#, INTD#. From now on we will call them
just A, B, C, and D. Each has its own pin on the edge connector of a
PCI card. Thus for a 7-slot system (for 7 cards) there could be 7 x 4
= 28 different interrupt lines for the cards. But the specs permit a
fewer number of interrupt lines, so many PCI buses seem to be made
with only 4 interrupt lines. This is not too restrictive since
interrupts may be shared. Call these lines (wires or traces) W, X, Y,
Z. There is an "interrupt router" chip that routes W, X, Y, Z to
selected IRQs. This routing can be changed by the BIOS or software.
For example, W may be routed to IRQ5. Suppose we designate the B
interrupt from slot 3 as interrupt 3B. Then interrupt 3B could be
permanently connected to W which is routed to IRQ5.
One simple method of connecting (hard-wiring) these lines from PCI
devices (such as 3B) to the interrupts W, etc. would be to connect all
A interrupts (INTA#) to line W, all B's to X, etc. This method was
once used many years ago but it is not a good solution. Here's why.
If a card only needs one interrupt, it's required that it use A. If
it needs two interrupts, it must use both A and B, etc. Thus INTA# is
used much more often than INTD#. So one winds up with an excessive
number of interrupts sharing the first line (W connected to all the
INTA#). To overcome this problem one may connect them in a more
random way so that each of the 4 interrupt lines (W, X, Y, Z) will
share about the same number of actual PCI interrupts.
One method of doing this would be to have wire W share interrupts 1A,
2B, 3C, 4D, 5A, 6B, 7C. This is done by physically connecting wire W
to wires 1A, 2B, etc. Likewise wire X could be connected to wires 1B,
2C, 3D, 4A, 5B, 6C, 7D, etc. Then on startup, the BIOS maps the X, W,
Y, Z to IRQs. After that it writes the IRQ that each device uses into
a hardware configuration register in each device. From then on, any
program interrogating this register can find out what IRQ the device
uses. Note that just writing the IRQ in a register on a PCI card
doesn't in any way set the IRQ for that device.
A practical use for the above is that, as a last resort, one may
change the IRQs of a PCI card by inserting it in a different slot. In
the above example, INTA# of a PCI card will be connected to wire W if
the card is inserted into slot 1 (1A maps to W) but INTA# will be
connected to wire X if it's inserted into slot 4 (4A maps to X).
A card in a slot may have up to 8 devices on it but there are only 4
PCI interrupts for it (A, B, C, D). This is OK since interrupts may
be shared so that each of the 8 devices (if they exist) can have an
interrupt. The PCI interrupt letter of a device is often fixed and
hardwired into the device. The assignment of interrupts is done by
the BIOS mapping the PCI interrupts to the ISA-like interrupts as
mentioned above. If there are only 4 lines (W, X, Y, and Z) as in the
above example, the mapping choices that the PCI BIOS has are limited.
Some motherboards may use more lines and thus have more choices. The
BIOS knows about how this is wired.
On the PCI bus, the BIOS assigns IRQs (interrupts) so as to avoid
conflicts with the IRQs it knows about on the ISA bus. Sometimes the
CMOS BIOS menu may allow one to assign IRQs to PCI cards or to tell
the BIOS what IRQs are to be reserved for ISA devices. Also, a PnP
operating system (for example MS Windows) could attempt to assign IRQs
after first finding out what the BIOS has done. The assignments are
known as a "routing table". If MS Windows makes such IRQ assignment
dynamically (such as a docking event) it's called "IRQ steering". The
BIOS may support it's own IRQ steering (which Linux could use). Thus
if Windows 9x changes what the BIOS set and you use Linux after
Windows without turning off your PC, the IRQs may be different.
Windows 2000 and XP doesn't change what the BIOS has set, but it may
add a new device (with a new IRQ).
You might think that since the PCI is using IRQs (designed for the ISA
bus) it might be slow since the ISA bus was slow. Not really. The
ISA Interrupt Controller Chip(s) has a direct interrupt wire going to
the CPU so it can get immediate attention. While signals on the old
ISA address and data buses are slow to get to the CPU, the IRQ
interrupt signals get there very fast.
[1m10.6. ISA Isolation[0m
This is only for the old ISA bus. Isolation is a complex method of
assigning a temporary handle (id number or Card Select Number = CSN)
to each PnP device on the ISA bus. Since there are more efficient
(but more complex) ways to do this, some might claim that it's a
simple method. Only one write address is used for PnP writes to all
PnP devices so that writing to this address goes to all PnP device
that are listening. This write address is used to send (assign) a
unique handle to each PnP device. To assign this handle requires that
only one device be listening when the handle is sent (written) to this
common address. All PnP devices have a unique serial number which
they use for the process of isolation. Doing isolation is something
like a game. It's done using the equivalent of just one common bus
wire connecting all PnP devices to the isolation program.
For the first round of the "game" all PnP devices listen on this wire
and send out simultaneously a sequence of bits to the wire. The
allowed bits are either a 1 (positive voltage) or an "open 0" of no
voltage (open circuit or tri-state). To do this, each PnP device just
starts to sequentially send out its serial number on this wire,
voltage (open circuit or tri-state). To do this, each PnP device just
starts to sequentially send out its serial number on this wire, bit-
by-bit, starting with the high-order bit. If any device sends a 1, a
1 will be heard on the wire by all other devices. If all devices send
an "open 0" nothing will be heard on the wire. The object is to
eliminate (by the end of this first round) all but highest serial
number device. "Eliminate" means to drop out of this round of the
game and thus temporarily cease to listen anymore to the wire. (Note
that all serial numbers are of the same length.) When there remains
only one device still listening, it will be given a handle (card
number).
First consider only the high-order bit of the serial number which is
put on the wire first by all devices which have no handle yet. If any
PnP device sends out a 0 (open 0) but hears a 1, this means that some
other PnP device has a higher serial number, so it temporarily drops
out of this round. Now the devices remaining in the game (for this
round) all have the same leading digit (a 1) so we may strip off this
digit and consider only the resulting "stripped serial number" for
future participation in this round. Then go to the start of this
paragraph and repeat until the entire serial number has been examined
for each device (see below for the all-0 case).
Thus it's clear that only cards with the lower serial number get
eliminated during a round. But what happens if all devices in the
game all send out a 0 as their high-order bit? In this case an "open
0" is sent on the line and all participants stay in the game. If they
all have a leading 0 then this is a tie and the 0's are stripped off
just like the 1's were in the above paragraph. The game then
continues as the next digit (of the serial number) is sent out.
At the end of the round (after the low-order bit of the serial number
has been sent out) only one PnP device with the highest serial number
remains in the game. It then gets assigned a handle and drops out of
the game permanently. Then all the dropouts from the previous round
(that don't have a handle yet) reenter the game and a new round begins
with one less participant. Eventually, all PnP devices are assigned
handles. It's easy to prove that this algorithm works. The actual
algorithm is a little more complex than that presented above since
each step is repeated twice to ensure reliability and the repeats are
done somewhat differently (but use the same basic idea).
Once all handles are assigned, they are used to address each PnP
device for sending/reading configuration data. Note that these
handles are only used for PnP configuration and are not used for
normal communication with the PnP device. When the computer starts up
a PnP BIOS will often do such an isolation and then a PnP
configuration. After that, all the handles are "lost" so that if one
wants to change (or inspect) the configuration again, the isolation
must be done over again.
[1m10.7. Bus Mastering and DMA resources[0m
If a bus has bus mastering available, it's unlikely that any resources
will be needed for DMA on that bus. For example, the PCI bus doesn't
need DMA resources since it has "bus mastering". However, "bus
mastering" is often called DMA. But since it's not strictly DMA it
needs no DMA resources. The ISA and VESA local bus had no bus
mastering. The old MCA and EISA buses did have bus mastering.
[1m10.8. Historical and Obsolete[0m
[1m10.8.1. OSS-Lite Sound Driver[0m
You must give the IO, IRQ, and DMA as parameters to a module or
compile them into the kernel. But some PCI cards will get
automatically detected. RedHat supplies a program "sndconfig" which
detects ISA PnP sound cards and automatically sets up the modules for
loading with the detected bus-resources.
[1m10.8.2. ALSA (Advanced Linux Sound Architecture) as of 2000[0m
This will detect the card by PnP methods and then select the
appropriate driver and load it. It will also set the bus-resources on
an ISA-PnP cards or PCI cards. OSS (Open Sound System) was formerly
popular.
[1m10.8.3. MS Windows Notes[0m
Windows NT4 didn't support ISAPNP but had a PNPISA program which one
could "use at your own risk". For NT4 users were advised to set "not
a PnP OS" in the BIOS so that the BIOS would do the resource
configuring. Thus both MS Windows and Linux were in olden days
dependent on the BIOS doing the configuring (and still are).
END OF Plug-and-Play-HOWTO
