PA-RISC/Linux Boot HOWTO
Thomas Marteau
TuxFamily
<marteaut@tuxfamily.org>
Deb Richardson
Original author
The Puffin Group
<deb@thepuffingroup.com>
Thibaut Varene
Contributor of v1.0
ESIEE
<varenet@esiee.fr>
Revision History
Revision 1.1 2003-11-01 Revised by: tm
Jeremy Drake's Windows?? 2k server boot howto has been added.
Revision 1.0 2002-10-04 Revised by: tm & tv
The content is done by Thibaut. Ready for Woody release. Glossary and
bibliography appear. XML conversion.
Revision 0.9 2002-01-15 Revised by: tm
This version brings you some useful advices for compiling your own kernel on
hppa systems.
Revision 0.8 2001-10-17 Revised by: tm
This version takes care of the change of name of the official FTP and CVS
sites and modify the license.
Revision 0.7 2001-10-13 Revised by: tm
This version adds some updates due to the progress of PA/Linux.
Revision 0.6 draft 2001-09-26 Revised by: tm
This version contains some minor changes and complete the "obtaining bootp/
tftpd" section.
Revision 0.5 draft 2001-07-03 Revised by: tm
This version is a large update from Deb's work.
Revision 0.3 draft 1999-11-24 Revised by: dlr
The initial and published version of this HOWTO.
This document outlines the procedures to get the PA-RISC/Linux kernel to boot
on your PA-RISC system. It also explains the usage of PALO, the kernel loader
for PA/Linux. You will find much information on how to compile a kernel from
the source available at [http://cvs.parisc-linux.org/] http://
cvs.parisc-linux.org/. Please note that this HOWTO version is newer than Deb
Richardson's and includes more accurate information because of the progress
of the port. Nevertheless, we must say that this document keeps some parts
from Deb's original one and reveals some of her hidden work.
If you are looking for some information related to HP hardware but not
directly to PA-RISC, please read Bruno Cornec's HP-HOWTO.
-----------------------------------------------------------------------------
Table of Contents
1. Introduction
1.1. Overview
1.2. Copyright and Licensing
2. Supported Hardware
3. Preparing to boot
3.1. BOOT_ADMIN
3.2. Consoles
4. Using PALO, the kernel loader for PA-RISC
4.1. What is PALO?
4.2. What does PALO?
4.3. PALO management tool usage
4.4. How to use PALO at early boot stage ?
5. Available boot solutions
5.1. Booting from CD
5.2. Booting from hard drive
5.3. Booting from network
6. Building and installing your own PA-RISC/Linux kernel
6.1. GCC compiler
6.2. Kernel configuration
6.3. Kernel installation
7. Windows?? 2k server boot howto
7.1. Setup your DHCP server
7.2. Get your TFTP server
7.3. Launch your netboot
8. HOWTO contributors
Glossary
Bibliography
-----------------------------------------------------------------------------
Chapter 1. Introduction
1.1. Overview
You just received this HP box you bought online or maybe you got it from your
company surplus. Anyway, here comes the question of the operating system you
are going to use. The PA/Linux project consists in porting Linux to the
PA-RISC architecture. Take a look at this Howto and you will see that Linux
could be the answer to this question. Anyway, we hope so.
In addition to port Linux, the development team is working on porting the
Debian project to PA-RISC. In fact, around 95 % of packages are ported and
up-to-date in the repository. The port can be consider as useful now. In
Debian3.0r0 called woody, the flavour "hppa" has been released for the first
time. Some Debian developers non involved in the port but yet curious
reported that the port was one of the easiest to install since you feel like
installing an i386 version.
For more information about the PA-RISC/Linux porting project, please see
[http://www.parisc-linux.org/] http://www.parisc-linux.org/, or a mirror like
[http://www.fr.parisc-linux.org/] http://www.fr.parisc-linux.org/. This site
deals with kernel development and improvement. For userspace troubles, please
refer to [http://www.debian.org/ports/hppa/] hppa Debian's port pages.
In a few words, this HOWTO is aimed to anyone looking for some help and
information about using Linux on a HP system based on PA-RISC architecture.
No special knowledge is necessary but bases about how Debian packages work
can be helpful.
If you care about just installing and you do not ask yourself about the way
it works, the best advice is to try a Debian release including the PA-RISC
port. The Woody version is now [ftp://ftp.de.debian.org/debian-cd/3.0_r0/hppa
/] available for hppa architecture. If you experience any trouble, try the
development netinst ISO images from the The PA/Linux ESIEE Team.
After listing the supported hardware, this HOWTO explains some commands of
the basic console available at boot time. Then, the features of the PA/Linux
kernel loader introduce another chapter showing many ways to get your system
up and running. At the end, the text goes deep in the kernel compilation and
configuration.
-----------------------------------------------------------------------------
1.2. Copyright and Licensing
Copyright 2002-2003 Thibaut Varene.
Copyright 2001-2003 Thomas Marteau.
Copyright 1999 The Puffin Group and Deb Richardson.
Permission is granted to copy, distribute and/or modify this document under
the terms of the GNU Free Documentation License, Version 1.1 or any later
version published by the Free Software Foundation; with no Invariant
Sections, with the Front-Cover Texts being 'Copyright and Licensing', and
with the Back-Cover Texts being 'HOWTO Contributors'. A copy of the license
can be found at [http://www.gnu.org/copyleft/fdl.html] http://www.gnu.org/
copyleft/fdl.html.
-----------------------------------------------------------------------------
Chapter 2. Supported Hardware
With the release of PA-RISC architecture in $Debian 3.0 (aka Woody), a major
improvement was made in term of quantity and quality of hardware support.
Since 0.9.3 released, the kernel has been greatly improved, so that much
unsupported hardware by the time 0.9.3 went out is now handled. That's why
even if your model is not listed here, you might give it a try and report
your result to the mailing list : <parisc-linux@lists.parisc-linux.org>. The
following PA-RISC machines can be booted almost like any other box of a
different architecture. We must add that this list can change at any time.
The best way to get an up to date version is to look at [http://
www.pateam.org/list.html] http://www.pateam.org/list.html. There you will
know if your hardware is supported and up to what level. For example, if you
can run PA/Linux using the serial console or the graphic card.
* All 712 models.
* All 715 models including Strider series.
* All 705, 710, 720, 730, 750 models should be running with the latest
ISO. It contains some modifications specially for hard disk devices.
* Some 725, 735 (no FWD SCSI), 755 models are running with the latest
kernels. But since there was not a lot of feedback about these machines,
we can not be more explicit.
* The VME-like systems are supported. This includes 742 and 743.
* A180 and similar.
* A500 and similar.
* BXXX models like B132, B160 and B180. These boxes can be used in the
framebuffer mode via the Standard Text Interface.
* BXXXX models like B1000, B2000 and B2600. These boxes can be used with
STI_CONSOLE, but framebuffer only works with VIS-EG cards. FX are not yet
supported.
* CXXX models like C110, C160, C180L, C240, C360.
* CXXXX models. Indeed, BXXXX and CXXXX are based on Astro/Elroy (aka SBA/
LBA) chipsets with varying CPU speeds, number of memory/PCI slots.
* D class works unless you have a Remote Management Card installed. Even
then, it still kind of works, it's just that ttyS0 gets assigned to the
second serial port and you have to switch cables around.
* E class : Christoph Plattner is working on his E55. E35 and E55 are
known to work diskless. The SCSI support is expected soon.
* J class is quite well supported. It has the same split as C class, i.e.
JXXX and J2240 are U2/Uturn based and JXXXX are Astro/Elroy. It is the
SMP version of CXXXX models.
* K class is supported if you are using the ISO images made by the [http:/
/www.pateam.org/download.html] ESIEE team tagged with "-PDC-".
* L class : L1000 and L2000, with serial console.
* R class is basically the same as D class.
No plan to get the following hardware completely supported in the near
future :
* L3000 - smaller brother of N class - currently only works Uni Processor
(UP).
* N class : N4000-55 seems to be supported in UP mode.
* F,G,H,I classes : Currently not supported.
* SuperDome : It boots "single-cell", multi-IOMMU doesn't work.
* T 5XX and V class : Nobody is working on it at the moment.
The following hardware might never work :
* T600.
-----------------------------------------------------------------------------
Chapter 3. Preparing to boot
Like any other system, machines based on PA-RISC processors have to go
through several steps in order to have PA/Linux up and running. The next
section introduces you to the early boot management of your PA-RISC computer.
To be a bit less awkward, we might from time to time call it a 'PA' box. This
chapter will give you some key concepts like BOOT_ADMIN.
-----------------------------------------------------------------------------
3.1. BOOT_ADMIN
First of all, you must learn what is and how to use BOOT_ADMIN on your
PA-RISC box, before thinking about doing any hacking on it.
BOOT_ADMIN is a firmware application, used to manage a PA-RISC machine at an
early boot stage, i.e. when the box has not yet started its Operating System.
You will see through this HOWTO that there are many references to it,
therefore it's worth saying that minimalistic BOOT_ADMIN skills are
mandatory !
-----------------------------------------------------------------------------
3.1.1. Entering the BOOT_ADMIN interface
Entering the BOOT_ADMIN management tool isn't that awful :
1. Turn your PA-RISC box on.
2. During the boot process, the following message will appear on the current
console (see Section 3.2) :
Searching for Potential Boot Devices.
To terminate search, press and hold the ESCAPE key.
When this message appears, press and hold the Esc key until an option
menu appears. This can take a while, be patient.
3. By default, you should enter the BOOT_ADMIN console. Though on some 715s
and 725s, an option menu looking like this may appear :
b) Boot from specified device
s) Search for bootable devices
a) Enter Boot Administration mode
x) Exit and continue boot sequence
?) Help
Select from menu:
Select 'a) Enter Boot Administration mode'. This will bring up a
'BOOT_ADMIN>' prompt.
Once you have the 'BOOT_ADMIN>' prompt, you can pat yourself on the back :
you are in BOOT_ADMIN mode !
-----------------------------------------------------------------------------
3.1.2. BOOT_ADMIN commands
BOOT_ADMIN is an early boot subsystem where you can execute some precise
commands. You should find here everything you need to know about them.
All HP-PA systems have BOOT_ADMIN. The display can be different but the idea
remains the same. That's why the following list is not complete but
consistent enough. Another important thing is that for each command, you have
a shorter way to invoke it. You can see the shortcut shown as uppercase
letters in the command name. Full names will be used in these sections.
Note Some commands may appear in several different menus, this is normal.
-----------------------------------------------------------------------------
3.1.2.1. The main commands
These commands are the basic ones.
* boot must be followed by an argument which indicates the path you want to
boot. The path should be the definition of a device like for example
FWSCSI.6.0 or PRI if you have set this variable correctly.
* path displays or sets the current paths. Invoked with only one argument
it will display the current path of the entity passed as argument : path
alt will display the current alternative boot path. path pri fwscsi.6.0
will setup the primary boot path as the device attached to Fast and Wide
SCSI controler with ID 6 and LUN 0. You can also set and display the
paths of console (graphics/serial) and keyboard (ps2/hil/usb).
* search is a very useful command. It automagically checks all possible
boot devices and displays all the bootable paths. In several firmware
versions, it links them to a shortcut (like P0. It can even search the
lan, if the box is able to boot it). You can restrain the search path
like : search lan or search disk.
* display redisplays the current menu.
* help gives you an overview of the available commands and their action.
help name will give you details on command name. By default, you can list
all main commands by typing help main.
* main will bring you back to the main menu, whatever menu you might be
currently consulting.
* On almost every systems, you have a reset instruction. It makes the box
reboot with the latest parameters you have set.
-----------------------------------------------------------------------------
3.1.2.2. The configuration commands
These commands are available in the configuration menu. So, in order to use
them, you must enter this menu by typing configuration at the 'BOOT_ADMIN>'
prompt.
* auto will tell you if the box will automatically start booting when
switched on, or will do a search for boot devices, depending on the first
argument passed to the command (boot, search, start). You can modify this
parameter with the keywords ON and OFF.
* default sets back the factory defaults.
* monitor (only in graphic mode) sets your display configuration by typing
monitor <path> <type> which indicates your console path and type. If you
do not know your monitor type, you can list those available via monitor
list.
* fastboot displays or sets the boot tests execution.
-----------------------------------------------------------------------------
3.1.2.3. The information commands
They give you access to global information about your system. Going into
this menu is done by asking for information.
* all should display everything.
* bootinfo lists all the boot parameters of the system.
* fwrversion gives your fimrware revision. You can check if your firmware
is up-to-date with [ftp://us-ffs.external.hp.com/firmware_patches/hp/cpu/
catalog] this link.
* lanaddress shows the MAC (ethernet) address of the system. On some boxes
(especially 712s), two different addresses may appear. The one you are
looking for is the first.
-----------------------------------------------------------------------------
3.1.2.4. The service commands
It is a PA-RISC guru menu. You will find nothing really interesting for an
end-user. We recommend you not to play with it unless you really know what
you are doing.
* pim [<proc>] [HPMC|LPMC|TOC] displays the content of a Processor Internal
Memory (PIM) and Error Log. It is very useful after a Transfer Of Control
(TOC) to collect debugging information.
* clearpim clears Processor Internal Memory (PIM) data.
* scroll enables or disables the scrolling mode in BOOT_ADMIN on recent
boxes.
-----------------------------------------------------------------------------
3.2. Consoles
In order to boot your PA-RISC system with the PA/Linux kernel, you must
first set up a console on it. A console is basically the device where the
kernel (and the firmware) will display its output, and where your can send
your input to control the system at an early boot stage. You can use either
graphic console, which requires to have a monitor and a keyboard attached to
the system, or serial console, which allows serial communication between the
system and another Linux machine, or any VT system. You should know that the
consoles for the firmware and for the kernel can be different. For example,
you can have to interact with the BOOT_ADMIN mode with a monitor and once PA/
Linux is up, you have ttys running on serial ports only.
Note Workstations usually boot in graphic mode, whereas servers boot in
serial mode. Some boxes will also automatically switch to serial if no
keyboard is connected, or if you hold down TOC switch while powering the
system on.
If you don't know what is the actual console of your box, it's quite
simple : this is where it will send its first output when switched on (serial
line or monitor output, if any).
If you are trying to setup a PA-RISC workstation and have a monitor handy,
the easiest method is to use graphic console. If you get into troubles, or
are trying to configure a server, choose serial console.
-----------------------------------------------------------------------------
3.2.1. Using graphic console
To use the graphic console, you must first ensure that the Linux kernel
supports your system's graphic card. There are two ways to deal with the
graphic console. If you think about bug-reporting any trouble, you must know
how to differenciate both. First, the STI console is the classical video text
console, like VGA on a common PC for example. This name is due to the fact
that each PA-RISC box features the Standard Text Interface which defines some
standardized ways to access the video memory. The other graphic console is
the well known framebuffer console (which on HP-PA uses STI in a special
manner, hence the name stifb). In this case, when booting, you will see a
characteristic little penguin appearing on the top-left corner. This is the
easiest way to differenciate the two graphic modes.
Obviously, if you can use graphic console, it is the easiest way to proceed.
Nevertheless, you must be sure that your hardware is supported.
-----------------------------------------------------------------------------
3.2.2. Using serial console
The serial console is a good way to get all console messages handy,
including the BOOT_ADMIN ones. It is very useful for bug reports, as its
output can be easily dumped. Moreover, most of the servers can only be
managed with serial console. Anyway, the only cases where you will HAVE TO
use serial console is either if you don't have a monitor for your PA-RISC
machine, or if your machine doesn't support graphics. It is also possible
that the kernel can NOT handle some specific graphic hardware present in your
model.
Here follows the procedure to setup serial console support.
-----------------------------------------------------------------------------
3.2.2.1. Serial Cable
To connect your PA-RISC machine to your PC's RS232 port, you need a
9-pin-to-9-pin female plugs null-modem cable. You should be able to obtain
such a cable at your local computer hardware reseller. Obviously, you can
also chose to connect the other end of the cable to a terminal (in this case
it will probably need a 25-pin male plug). Anyway, the most practical method
is to connect it to another box running minicom or cu, which makes all output
easily available for further usage (dump report, session log, and so on).
-----------------------------------------------------------------------------
3.2.2.2. Configuring minicom on Linux
In order to communicate with your PA-RISC machine, you have to set it up in
serial console mode (see below) and configure a serial communication program.
We recommend minicom, which can be found in most Linux distributions. If you
don't have minicom on your system, you can find the latest package on any
major Linux software website.
Most of the minicom configuration is machine dependent. However, you must
ensure that :
a. The baud rate is set to 9600
b. Protocol is set to 8-N-1 (8bit data, No parity check, 1 stop bit)
Don't worry too much as these are the default values for all PA-RISC
systems. If you are running minicom on a PC, you will probably need to change
the baud rate.
-----------------------------------------------------------------------------
3.2.3. Switching consoles
It might prove useful that you learn how to manage the console mode on your
PA-RISC box. The following sections will explain the various operations on
console modes.
-----------------------------------------------------------------------------
3.2.3.1. Checking current console mode
Type : path console to see the current console mode.
If it's graphic console mode, it will return something like : 'Console path
= graphic_1'.
If it's serial console, it will return : 'Console path =
rs232_a.9600.8.none' or something similar.
Note For some models, you can find slight differences but the idea stays the
same. If you want to see more descriptions here, please send us a
message describing the box you use and what you get.
-----------------------------------------------------------------------------
3.2.3.2. Changing to serial console mode
To change to serial console mode, type the following command at the
'BOOT_ADMIN>' command prompt :
path console rs232_a.9600.8.none
or, like on B132L+
path console serial_1
Anyway, on most boxes if you try to setup an invalid path for the console,
you will be warned and prompted again for a valid path. To verify that the
console path has been correctly set, type path console. This should return
'Console path = rs232_a.9600.8.none', indicating that the system is now set
up to boot in serial console mode, on RS232 port 'A'. If your machine has
only one, this is OK, if not, take care to use the right one. By default,
reset will reboot your system with the new parameters.
-----------------------------------------------------------------------------
3.2.3.2.1. How can I change the boot console to serial on a 712?
Unfortunately, it is *normally* not possible. Although 712s are configured
for in-house HP development to use serial console, this cannot be set in
BOOT_ADMIN. You will have to use graphic console on 712s. And why the hell
would we use this beautiful 712 with serial console when we can have X on
it ? !
Anyway, if you feel like trying bleeding edge solutions, there is a tip at
the [http://lists.parisc-linux.org/pipermail/parisc-linux/1999-December/
008117.html] PA/Linux mailing list archive. This describes how to change the
console from an HP/UX ISL prompt. You can find a small HP/UX lifimage here :
[http://www.pateam.org/archive/uxbootlf] http://www.pateam.org/archive/
uxbootlf. (See further Section 5.3 to learn how to netboot a lifimage). In
fact, serial console on 712 is only useful if you want to boot the box
without any keyboard attached to it, which is otherwise not possible.
Here is the procedure :
1. Turn the box on and when in BOOT_ADMIN, boot to HP/UX ISL. For example :
BOOT_ADMIN> boot lan isl
2. Once you get the 'ISL>' prompt, type the following :
+ For switching to serial : conspath 2/0/4.0x283
+ For switching to graphic : conspath 1/0/0.0
3. Still at the 'ISL>' prompt, type disp, and check that console path is
either '(hex) 2/0/4.283.0.0.0.0.0' for serial, or '(hex) 1/0/
0.0.0.0.0.0.0' for graphic.
4. Power cycle the system to bring it up on the new console.
-----------------------------------------------------------------------------
3.2.3.3. Changing to graphic console mode
It is the opposite operation compared to the previous one. By checking your
console path, you should see 'Console path = rs232_a.9600.8.none'. Now, you
must set the graphic mode by issuing the following command at 'BOOT_ADMIN>'
prompt :
path console graphic_1
You should get the display available on the monitor after a reset. If the
screen does not seem to work properly, try to press the Tab key (on the
keyboard attached to the box of course) at the beginning of the boot sequence
to change the resolution of the display. By pressing this key, the monitor
resolution cycles from one to another. Perhaps you will need to do this
operation several times. This is also true when you change your monitor.
-----------------------------------------------------------------------------
Chapter 4. Using PALO, the kernel loader for PA-RISC
4.1. What is PALO?
PALO is a set of two programs, a boot loader, which is loaded by the PA-RISC
firmware in memory and then executed, and a boot media management tool, which
prepares and updates bootable media such as hard disk drives. The PALO boot
loader executable is stored in a file called iplboot. 'IPL' is HP jargon for
Initial Program Loader. The boot media management tool is called PALO, which
stands for PA/Linux LOader, just as on x86 the boot media management tool is
called LILO, though it's worth mentionning that PALO doesn't usually need to
be called every time you build and install a new kernel, as LILO does. PALO
is strongly related to PA/Linux development. Thus, several versions has been
released. The last changes are explained by the author of PALO, Paul Bame, in
this [http://lists.parisc-linux.org/hypermail/parisc-linux/9451.html] mail.
-----------------------------------------------------------------------------
4.2. What does PALO?
The main idea is to boot a kernel, passing it all needed parameters. This is
what the boot loader part of PALO does (see Section 4.4). Once it has been
called by the firmware, it will load the Linux Kernel in memory, passing to
it the given arguments, and tell the processor to branch to its entry point.
This will begin the execution of the kernel on the PA-RISC computer.
The PALO management tool can transform the usual vmlinux into a PA-RISC
bootable lifimage, including or not RAMDISK or NFSROOT support. However, it
can also make a hard disk drive bootable, specifying the console output and
the root device. We are going to see all these points precisely.
Important What must be kept in mind is that vmlinux is the kernel alone,
which is not bootable by itself. It needs PALO to be turned into a
bootable lifimage for CD or network boot, or to be launched at boot
time from a prepared hard disk drive. Have a look at Glossary about
these words. Quoting Richard Hirst, a PA/Linux hacker : "People
often try to put a lifimage in /boot, or a vmlinux on the network".
Which is obviously wrong.
-----------------------------------------------------------------------------
4.3. PALO management tool usage
Here we will show you what can be done with the PALO boot media management
tool. For in-depth information about palo usage, we strongly advise you to
take a look at PALO's README file, which can be found in palo/ directory on
[http://cvs.parisc-linux.org/] http://cvs.parisc-linux.org/.
For the next two steps, you will need a compiler toolchain, see Section 6.1.
-----------------------------------------------------------------------------
4.3.1. Making a lifimage with RAMDISK
First things first : when should you go this way ?
At an earlier step of the PA/Linux project, the lifimage was very useful. In
fact, simply putting this file in a boot server tree allows you to boot your
HP box via the boot lan instruction without any further involvement (see
Section 5.3). The main advantage of a RAMDISK is that it unpacks its own file
system in RAM, and therefore is completely independant from the machine I/O
capabilities (hard drives, etc). The main drawback is that you have to build
your own RAMDISK if you have memory constraints or some customized files.
Now, let's see how to obtain a lifimage with RAMDISK.
Tip If you don't want to mess with building your own RAMDISK, you can use
root.bin that can be found on [http://ftp.debian.org/debian/dists/
Debian3.0r0/main/disks-hppa/current/root.bin] Debian Boot-Floppies.
We assume you got the latest source of the PA/Linux kernel. Mainly, you will
need a (cross-)compiler, the linux/ directory and the PALO package installed.
If you do not have it, run as root apt-get install palo. Everything can be
found at [http://www.parisc-linux.org/] http://www.parisc-linux.org/. Go
through the make menuconfig step. Then, run make palo and if you have the
PALO installed, you should get this message at the end of the compilation :
A generic palo config file (./palo.conf) has been created for you.
You should check it and re-run "make palo".
WARNING: the "lifimage" file is now placed in this directory by default!
So, edit the palo.conf file :
# This a generic Palo configuration file. For more information about how
# it works try 'palo -?'.
#
# Most people using 'make palo' want a bootable file, usable for
# network or tape booting for example.
--init-tape=lifimage
--recoverykernel=vmlinux
########## Pick your ROOT here! ##########
# You need at least one 'root='!
#
# If you want a root ramdisk, use the next 2 lines
# (Edit the ramdisk image name!!!!)
--ramdisk=ram-disk-image-file
--commandline=0/vmlinux HOME=/ root=/dev/ram initrd=0/ramdisk
# If you want NFS root, use the following command line (Edit the HOSTNAME!!!)
#--commandline=0/vmlinux HOME=/ root=/dev/nfs nfsroot=HOSTNAME ip=bootp
# If you have root on a disk partition, use this (Edit the partition name!!!)
#--commandline=0/vmlinux HOME=/ root=/dev/sda1
As you can see, the RAMDISK mode is the default. The string
ram-disk-image-file should give to PALO the path of your RAMDISK file. You
shouldn't change anything else to this file. After configuring the palo.conf,
you can go back to your make palo. The result, a lifimage file, is waiting
for you in the linux/ directory.
-----------------------------------------------------------------------------
4.3.2. Making a lifimage with NFSROOT
This method is widely used because the kernel and the file system are
directly accessible on your boot server. It is also very easy to test a new
kernel. You just have to generate the kernel and put it in the correct
directory. When starting up, the PA-RISC box will boot via the boot lan
instruction its new kernel.
Getting the NFSROOT support is easier than RAMDISK. You have to edit the
palo.conf to specify the boot server IP address instead of the string
HOSTNAME. In fact, if your server has 10.10.10.2 as its IP adress, then the
palo.conf file should contain :
# This a generic Palo configuration file. For more information about how
# it works try 'palo -?'.
#
# Most people using 'make palo' want a bootable file, usable for
# network or tape booting for example.
--init-tape=lifimage
--recoverykernel=vmlinux
########## Pick your ROOT here! ##########
# You need at least one 'root='!
#
# If you want a root ramdisk, use the next 2 lines
# (Edit the ramdisk image name!!!!)
#--ramdisk=ram-disk-image-file
#--commandline=0/vmlinux HOME=/ root=/dev/ram initrd=0/ramdisk
# If you want NFS root, use the following command line (Edit the HOSTNAME!!!)
--commandline=0/vmlinux HOME=/ root=/dev/nfs nfsroot=10.10.10.2 ip=bootp
# If you have root on a disk partition, use this (Edit the partition name!!!)
#--commandline=0/vmlinux HOME=/ root=/dev/sda1
If you have another IP, this field must be filled in with the correct data.
You shouldn't change anything else to this file. After having configured the
palo.conf, you can go into the linux/ directory and issue a make palo. The
result, a lifimage file, is as usual waiting for you in the linux/ directory.
For advanced details on NFSROOT management, take a look at Bibliography for
the appropriate HOWTOs.
-----------------------------------------------------------------------------
4.3.3. Making a bootable partition
This part is where PALO can be seen as a LILO clone. PALO is mainly a
program that enables a PA box to boot a kernel present on its own hard disk
drive. This section is going to explain how to make it work. When installing
the PALO package, Paul Bame, the author and maintainer, put a copy of the
default /etc/palo.conf in /usr/share/doc/palo/palo.conf. If you want to
understand how PALO works, you just have to read this file !
To setup a bootable hard disk, you have to partition properly your hard
drive (if any, and if you want to use it as your primary boot device). This
implies that this step can only be achieved either if you have already booted
a minimal system on your PA-RISC box (via CD or network, see Chapter 5), or
if you intend to prepare your hard disk using another computer than the
target (which can be useful to unpack and setup a downloaded file system for
example). The point of this HOWTO is not to teach you how to use fdisk or
other, so here are the few things you HAVE TO know :
* A partition within the first 2GB of your target device has to be of
partition type 'f0', which is the reserved partition type for PALO boot
loader.
* It does not need to be huge. This is were PALO will save its
configuration, recovery kernel(s) - about 5MB each - and optional
ramdisk. 16-32MB seems far sufficient.
Warning Beware ! Your vmlinux has also to be located within the first 2GB of
the hard disk. We strongly recommend to create a separated /boot
partition at the front of the disk if your '/' is bigger than that,
because if ever your vmlinux goes above the first 2GB of the disk
(like when filling up '/' with data), the box won't boot anymore.
Here is the output of fdisk which represents the hard drive of a box with
16MB PALO space, 128MB swap space and about 1GB '/' partition :
bash# fdisk -l /dev/sda
Disk /dev/sda: 133 heads, 62 sectors, 1017 cylinders
Units = cylinders of 8246 * 512 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 4 16461 f0 Linux/PA-RISC boot
/dev/sda2 5 34 123690 82 Linux swap
/dev/sda3 * 35 277 1001889 83 Linux
Now let's deal with PALO configuration. Here are the various parameters you
can change :
* recoverykernel is the path to the kernel that you want to boot within a
failsafe session, it will be stored in the 'f0' partition.
* bootloader is the path to the iplboot boot loader utility which is
created by PALO when you issue a make iplboot.
* init-partitioned is used to indicate the pre-partionned device where palo
will write its boot parameters. The effect is immediate. It means that
PALO is going to write on the first octets of the first partition of this
device, which partition-type must be 'f0', as shown above.
* commandline : the first digit is the number of your ext2 partition where
the kernel file is located, as reported by fdisk. Logically, the next
string is the absolute path to the kernel. The following space separated
parameters will be passed to the kernel as its arguments. e.g. : HOME=
and TERM= are environmental parameters passed to init when booting. They
are not compulsory but they can be useful. root= tells the kernel which
partition it must mount as the root file system while booting. It can be
tricky when you have more than one disk.
You can also add console=, to force the designation of the output
console. You should remind that console=ttyS0 is for a serial console and
console=tty0 is for a STI-console. Recently, support for the PDC console
(if enabled in the kernel, see Section 6.2.3) has been added, using
console=ttyB0. Indeed, the latest versions of PALO autodetect the right
console path (except for PDC), and can figure out whether a 32bit or
64bit kernel should be used. If not, please mail to the mailing list.
In fact, this third usage of PALO is the most common but the default /etc/
palo.conf makes it easy to configure. Just choose your root partition. It
should the partition containing your root directory. According our fdisk
example, we want /dev/sda3. Thus, the configuration file should look like
that :
# The following arguments are set up for booting from /dev/sda3, specifically
# mounting partition 3 as root, and using /boot/vmlinux as both the
# recovery kernel, and the default dynamically-booted kernel.
--recoverykernel=/boot/vmlinux
--bootloader=/boot/iplboot
--init-partitioned=/dev/sda
--commandline=3/boot/vmlinux HOME=/ TERM=linux root=/dev/sda3
-----------------------------------------------------------------------------
4.4. How to use PALO at early boot stage ?
4.4.1. The theory
You have setup everything, rebooted your box, and suddendly you want to
change something to the kernel boot arguments, or even boot another kernel.
Damn it ! How could you, now that the box is booting ? Well, stay calm and
relax, we have the solution !
First, you must learn how to interact with PALO during the startup sequence.
You have to enter BOOT_ADMIN, as explained in Section 3.1.1. For some old
models (up to 712 or so), you must add the ipl (or isl) string to your boot
command in the BOOT_ADMIN console :
BOOT_ADMIN> boot pri ipl
On most PA-RISC boxes, the system will ask you if you want to interact with
IPL anyway. You just have to answer by a "y". You will fall back to PALO
configuration display, with the list of all parameters and their
corresponding numbers.
You just have to enter the number corresponding to the parameter you want to
change. Hit ENTER, modify it and validate the changes by hiting ENTER again.
The system will redisplay the new list. This modification is not permanent !
To save your changes, you will have to run /sbin/palo when your system will
be up and running, and it will write on the disk all the parameters contained
in the default file, (/etc/palo.conf), which you will have properly modified
if needed. If you want to add a supplementary parameter, select any one and
write yours on the editing line, beginning with a space :
Edit which field?
(or 'b' to boot with this command line)? 0
3/boot/vmlinux initrd=root.bin
After validation, the list will count one more parameter. If you want to
delete one, select it and erase the complete entry. You will see that the
list counts one less parameter.
For more informations about PALO, please take look at the PALO readme. This
section is mostly inspired from Paul Bame's file as well as the page about
PALO you can find at [http://www.pateam.org/palo.html] http://www.pateam.org/
palo.html.
-----------------------------------------------------------------------------
4.4.2. A complete example
This example has been suggested by Michael Damaschke. So, let's go for the
story of the happy PA/Linux user booting a kernel, also called "I don't know
how to configure my workstation to use the kernel I want during boot
sequence !".
After switching your workstation and monitor on, a message on the screen
will tell you that the workstation is about to start automatically the boot
sequence, except if you hold the Esc key to stop the auto-booting. This is a
very difficult step : you must hold the Esc key down ;o)
Warning Depending on your model, you might need to press this key during a
quite long time.
Tip In some cases, the monitor can be too slow to get on, and won't allow you
to see the warning message. A good workaround is to keep a close eye on
the keyboard's lights : when they blink, this is the right time to press
and hold the Esc key. If you still have troubles, please refer to the
Consoles section.
There are few differences about the way to get access to BOOT_ADMIN (see
Section 3.1.1). If you have an old box, you will get an information message
displayed, where the workstation's firmware tells you that it will start
searching for all bootable devices, or that you can break this by holding
down the Esc key. This is the same procedure as before, you must press the
Esc key.
You might then get a menu where you must press the a-key followed by ENTER
-key. You are now facing the deadly 'BOOT_ADMIN>' prompt :^). First, we will
turn off auto boot process by entering the following lines :
BOOT_ADMIN> auto boot off
then hit the ENTER key.
After that, you must tell the system from which boot device you would like
to boot. If it's a hard drive, it must have a 'f0' partition at the beginning
(see Chapter 5).
In this example, the old kernel is vmlinux and the new one is
vmlinux-2.4.17-pa3. The chosen SCSI boot device is designed by : SCSI.X.0,
where X is the SCSI-ID of the disk you want to boot from. e.g.
BOOT_ADMIN> boot SCSI.5.0
At the end of the previous command line, you must add the IPL token if you
have a HP 9000/7xx system to specify that you want to interact with IPL. If
you have a more recent hardware, the system will ask if you want to interact
with IPL anyway :
Interact with IPL (Y or N)?>
Now, you can manually configure the PALO booting parameters. You can see a
new menu, where you can configure on line '0' (selected by default) the boot
partition number, and the path of your boot kernel.
Here is the complete session log of a A500 serial console output :
Main Menu: Enter command or menu > bo scsi.5.0 ipl
Interact with IPL (Y, N, or Cancel)?> y
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
palo ipl 0.97 root@c3k Tue Nov 27 14:51:48 MST 2001
Information: Boot device can't seek past 2Gb (ignore next error).
byteio_read: seekread() returned -1 expected 2048
Partition Start(MB) End(MB) Id Type
1 1 15 f0 Palo
2 16 503 82 swap
3 504 2887 83 ext2
PALO(F0) partition contains:
0/vmlinux64 3990942 bytes @ 0x44000
Information: No console specified on kernel command line. This is normal.
PALO will choose the console currently used by firmware (serial).
Current command line:
3/boot/vmlinux root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102
0: 3/boot/vmlinux
1: root=/dev/sda3
2: HOME=/
3: console=ttyS0
4: TERM=vt102
Edit which field?
(or 'b' to boot with this command line)? 0
3/boot/vmlinux-2.4.17-pa3 initrd=0/root.bin
Current command line:
3/boot/vmlinux-2.4.17-pa3 initrd=root.bin root=/dev/sda3 HOME=/
console=ttyS0 TERM=vt102
0: 3/boot/vmlinux-2.4.17-pa3
1: initrd=0/root.bin
2: root=/dev/sda3
3: HOME=/
4: console=ttyS0
5: TERM=vt102
Edit which field?
(or 'b' to boot with this command line)? 1
Current command line:
3/boot/vmlinux-2.4.17-pa3 root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102
0: 3/boot/vmlinux-2.4.17-pa3
1: root=/dev/sda3
2: HOME=/
3: console=ttyS0
4: TERM=vt102
Edit which field?
(or 'b' to boot with this command line)? b
PALO was first setup to boot the kernel file vmlinux located on the third
partition of the SCSI device ID 5 LUN 0. (We know this since we have asked
BOOT_ADMIN to boot on this device). But we wanted another kernel this time.
We have pressed the ENTER key (to validate the default choice '0') and modify
the text to match our needs, here vmlinux-2.4.17-pa3. We have also added an
initrd=0/root.bin argument to the command line. We have validated our changes
by hitting the ENTER key. Finally we have decided that we didn't want this
additional argument, so we have selected it and erased it. At the end it
asked again which field we wanted to edit, we have just put 'b' instead of
any number and hit ENTER to boot our new kernel.
Caution Please don't change any other parameter unless you really know what
you do !
That's it ! PALO has no more secrets for you :-)
Note As you might have noticed, the BOOT_ADMIN interface can take several
apparences, so don't be disappointed if yours does not match our
examples.
-----------------------------------------------------------------------------
Chapter 5. Available boot solutions
5.1. Booting from CD
Booting from CD is one of the easiest way to start and install your PA-RISC
machine; assuming you have a CD drive handy and a bootable CD. You can
download official PA/Linux ISOs as well as recent Net Install ISO (see
Glossary) at [http://www.pateam.org/download.html] The PA/Linux ESIEE Team
download page, or at [ftp://www.parisc-linux.org/cd-images/] PA-RISC/Linux
official website.
i. start the box and enter the BOOT_ADMIN mode. (Section 3.1.1)
ii. Dispose your bootable CD on the CD tray and close it. Sounds obvious,
but we know guys who missed that step :)
iii. There are two options from there : either you know the full PATH to
your CD device, then you can jump to next step, or you don't. In this
last case, issue a search ipl to list all available devices with IPL. You
can also specify a search [PATH], which is fastest. For instance if you
want to search the SCSI bus:
search SCSI
On recent boxes, search disk is quite helpful. Take a look at help
search for details specific to your box.
iv. Once you know the full PATH to your CD drive, you can issue a boot <PATH
>. That's all. If everything goes fine, it will start booting the CD
present in the CD reader. Real life example :
boot ide
-----------------------------------------------------------------------------
5.2. Booting from hard drive
Booting from Hard Drive is not really more difficult that booting from CD.
The only thing really important is that your hard drive has to be correctly
prepared. Take a look at Section 4.3.3 to learn how to prepare your hard
drive.
i. start the box and enter the BOOT_ADMIN mode. (Section 3.1.1)
ii. There are two options from there : either you know the full PATH to your
hard disk device, then you can jump to next step, or you don't. In this
last case, issue a search ipl to list all available devices with IPL. You
can also specify a search [PATH]. For instance if you want to search the
Single Ended SCSI bus :
search SESCSI
Take a look at help search for details specific to your box.
iii. Once you know the full PATH to your hard drive, you can issue a boot <
PATH>. That's all. If everything goes fine, it will start booting the
kernel as setup by PALO (see Section 4.3.3). Real life example :
boot scsi.6
-----------------------------------------------------------------------------
5.3. Booting from network
5.3.1. Preparing to boot from network
This is a very old way to operate but it used to be the only one available
for a long time. Usually you won't need to boot from network, except in some
very specific cases (e.g. unsupported I/O devices). That's why it is detailed
here.
Important You will need a lifimage to perform a network boot. See Section 4.2
to learn how to create one. You can also download one at [http://
www.pateam.org/cd-images/lifimages/] http://www.pateam.org/
cd-images/lifimages/
-----------------------------------------------------------------------------
5.3.2. rboot or bootp?
All 'recent' machines can boot using bootp, starting from 715/100, 715/120,
and 712s. Older ones, mostly early 715s, 710s and 725s need rboot.
Note To use BOOTP you have to enable the 'IP: Kernel level autoconfiguration
-> IP: BOOTP support' within the 'Networking options' section of the
kernel configuration, if you want to use a home-made kernel. See Chapter
6 for details.
-----------------------------------------------------------------------------
5.3.3. Using rboot
5.3.3.1. Obtaining rboot
If you have an old machine that requires rboot to boot over network, use the
following procedure to set up, configure, and boot using the PA-RISC/Linux
kernel.
Old machines, including the Scorpio 715s, require rbootd. You can obtain the
rboot daemon :
* For all distributions but Debian, by getting our archive at [http://
www.pateam.org/download.html#deb] http://www.pateam.org/download.html#deb
* For Debian, from [http://www.debian.org/Packages/stable/net/rbootd.html]
http://www.debian.org/Packages/stable/net/rbootd.html, or even more
simple :
bash# apt-get install rbootd
-----------------------------------------------------------------------------
5.3.3.2. Configuring rbootd
For instance, to boot a PA-RISC 715 system, you need a Linux system with
rbootd installed (this is the 'boot server') on which you will store the
PA-RISC/Linux kernel lifimage that you want to use to boot your PA-RISC
system with.
Once the rbootd server software is installed, do as follows to configure it
to work with your PA-RISC system :
In /etc/rbootd.conf you will have to add a line like :
ethernet_addr bootfile
1. Replace bootfile with the name of your PA-RISC/Linux kernel image,
usually 'lifimage'.
2. Now get the ethernet address of your PA-RISC system by typing lanaddress
at the 'BOOT_ADMIN>' prompt (see Section 3.1.2.3).
It will return a number like 080009-7004b6. Take note of this number.
3. In /etc/rbootd.conf on your boot server, the ethernet address has to be
colon-delimited. That means you will have to modify the number you just
obtained so that every set of two characters (after removing the '-') is
separated by a colon. For example :
080009-7004b6
becomes
08:00:09:70:04:b6
Add the colon delimited ethernet address to /etc/rbootd.conf on your
boot server. The resulting file will look something like this :
# ethernet addr boot file comments
08:00:09:87:e4:8f lifimage_715 # PA/Linux kernel for 715/33
08:00:09:70:04:b6 lifimage_720 # PA/Linux kernel for 720
This rbootd.conf example contains the ethernet addresses and boot file
names for two different machines.
Once you have changed the configuration file, restart rbootd.
By default, rbootd assumes that bootfiles are located in /var/lib/rbootd/.
If you use our archive for other distributions, this directory is /export/hp/
rbootd/. Therefore, you will have to put your bootable kernel image in that
directory, or, if you really hate that directory for some reason, you can
recompile rbootd to use a different directory.
The easiest thing, of course, is just to drop your kernel images in the
default directory !
-----------------------------------------------------------------------------
5.3.4. Using dhcp/tftp
We will see here how to use a DHCP server as a BOOTP one.
-----------------------------------------------------------------------------
5.3.4.1. Obtaining dhcp/tftp
Debian users will just have to install the packages via these commands as
root :
bash# apt-get install dhcp
bash# apt-get install tftpd
If you need rpm packages (for the ISC dhcp server), the best way is to go to
[http://rpmfind.net/] http://rpmfind.net/. It seems that Red Hat users need
to create the user "nobody" belonging to the group "nogroup". The files
present in your /tftpboot/ directory (see below) should have these user/group
privileges.
Note The dhcp package can do far more than a simple bootp daemon.
Nevertheless, it is also known to be far easier to configure. If you
really want to try bootp, skip this and go to Section 5.3.5.
-----------------------------------------------------------------------------
5.3.4.2. Configuring dhcp/tftp
Here are the instructions to set up dhcp on your boot server. To keep this
explanation simple, we will assume that you want to assign a fixed IP to your
box, without DNS update. Your subnet will be 192.168.1.0/24, with optional :
gateway at 192.168.1.1, domain name foo.com and DNS at 192.168.1.4.
Note This section is dedicated to Debian users. For others distributions, it
should be similar though there can be some differences like default
directories. Since Debian maintains a dhcp package, we will focus on it
only.
1. Edit /etc/inetd.conf on your boot server to add the following line, if
it doesn't already exist :
tftp dgram udp wait nobody /usr/sbin/tcpd \
/usr/sbin/in.tftpd /tftpboot
Here, /tftpboot/ is being used as tftpd server's root. You can choose
another directory if you want. According to man tftpd, this is the usual
default directory.
When this is done, restart inetd with : /etc/init.d/inetd restart. You
can also issue a killall -HUP inetd.
2. According to man 5 dhcpd.conf, edit the /etc/dhcpd.conf file to contain
something like :
allow bootp;
default-lease-time 600;
max-lease-time 7200;
# This will tell the box its hostname while booting:
use-host-decl-names on;
subnet 192.168.1.0 netmask 255.255.255.0 {
option routers 192.168.1.1;
option domain-name "foo.com";
option domain-name-server 192.168.1.4;
}
host [hostname] {
hardware ethernet [mac address];
fixed-address [ip address];
filename "[boot filename]";
option root-path "[root path]";
}
You have to fill in the [hostname], [mac address], [ip address], [boot
filename] and [root path] fields with the appropriate information,
where :
+ [hostname] is the name of the PA-RISC system.
+ [mac address] is the colon-delimited ethernet address of the PA-RISC
system, which can be obtained by typing lanaddress at the 'BOOT_ADMIN
>' prompt (see Section 3.1.2.3).
+ [ip address] is the IP address you wish to assign to the PA-RISC
system.
+ [boot filename] is the name of the bootable kernel image you want to
boot your system with.
+ [root path] is the path to the NFS root filesystem exported by the
server.
You'll end up with something like this for each box you want to netboot
:
host tatooine {
hardware ethernet 00:40:05:18:0c:dd;
fixed-address 192.168.1.22;
filename "lifimage-tatooine";
option root-path "/exports/tatooineroot";
}
-----------------------------------------------------------------------------
5.3.5. Using bootp/tftp
5.3.5.1. Obtaining bootp/tftp
For Debian users, you just have to install the packages via these commands
as root :
bash# apt-get install bootp tfptd
If you need rpm packages, the best way is to go to [http://rpmfind.net/]
http://rpmfind.net/. It seems that Red Hat users need to create the user
"nobody" belonging to the group "nogroup". The files present in your /
tftpboot/ directory (see below) should have these user/group privileges.
Warning You'll have been warned ! This daemon is far more obfuscated in its
configuration.
-----------------------------------------------------------------------------
5.3.5.2. Configuring bootp/tftp
Follow these instructions to use bootp on your boot server :
Note This section is dedicated to Debian users. For others distributions, it
should be similar though there can be some differences like default
directories. Since Debian maintains a bootp package, we will focus on it
only.
1. Edit /etc/inetd.conf on your boot server to add the following lines, if
they don't already exist :
tftp dgram udp wait nobody /usr/sbin/tcpd \
/usr/sbin/in.tftpd /tftpboot
bootps dgram udp wait root /usr/sbin/bootpd \
bootpd -i -t 120
Here, /tftpboot/ is being used as tftpd server's root. You can choose
another directory if you want. According to man tftpd, this is the usual
default directory.
When this is done, restart inetd with : /etc/init.d/inetd restart. You
can also issue a killall -HUP inetd.
2. According to man 5 bootptab, edit the /etc/bootptab file to contain :
[hostname]:hd=/tftpboot:\
:rp=[root path]:\
:ht=ethernet:\
:ha=[mac address]:\
:ip=[ip address]:\
:bf=[boot filename]:\
:sm=255.255.255.0:\
:to=7200:
You have to fill in the [hostname], [mac address], [ip address] and [root
path] fields with the appropriate information, where :
+ [hostname] is the name of the PA-RISC system.
+ [mac address] is the NOT-delimited ethernet address of the PA-RISC
system, which can be obtained by typing lanaddress at the 'BOOT_ADMIN
>' prompt (see Section 3.1.2.3).
+ [ip address] is the IP address you wish to assign to the PA-RISC
system.
+ [boot filename] is the name of the bootable kernel image you want to
boot your system with.
+ [root path] is the path to the NFS root filesystem exported by the
server.
You'll end up with something like this :
vodka:hd=/tftpboot:\
:rp=/usr/src/parisc/:\
:ht=ethernet:\
:ha=080069088717:\
:ip=140.244.9.208:\
:bf=lifimage:\
:sm=255.255.255.0:\
:to=7200:
-----------------------------------------------------------------------------
5.3.6. Booting your PA/Linux system from network
To conclude with the developers' way to boot the kernel, this section will
tell you how to actually boot your system from a network server. But it tends
to be less and less used. Most users will prefer to stick to Section 5.2.
Here we are. These are just some tips to get the boot for those who tried the
network way. We assume that you've done everything outlined above, your
development PC is on the same subnet than your PA-RISC machine, you've got a
bootable PA/Linux kernel lifimage on your boot server, and you're willing to
give it a try. If everything is ready, as well as you, the following
procedure will introduce you to the joy of network booting your PA box into
Linux.
1. Fire up your PA-RISC system.
2. Watch your PA-RISC box starting up. When the following message appears
during the PA-RISC machine's boot process, press and hold the Esc key :
Searching for Potential Boot Devices.
To terminate search, press and hold the ESCAPE key.
3. If needed, select 'a) Enter Boot Administration mode' from the menu. This
brings up the 'BOOT_ADMIN>' prompt.
4. Type the following at the prompt : boot lan.
5. Watch your PA-RISC system magically becoming a PA/Linux system. Ta dah !
Note Of course your are supposed to run only one boot server at a time on
your network, in order to avoid conflicts...
-----------------------------------------------------------------------------
Chapter 6. Building and installing your own PA-RISC/Linux kernel
To build a Linux kernel, you need a compiler and the kernel source. The
first element is not a trivial thing to find because it depends on how you
want to build your kernel. The second is easier since it lies on [http://
cvs.parisc-linux.org/] the official CVS site. First, we will discuss about
GCC compiler. Then, the configuration of your build will be explained. The
last paragraph will deal with the installation of this new kernel.
Note We will deal only with a kernel built without modules, to simplify the
explanations.
-----------------------------------------------------------------------------
6.1. GCC compiler
You can compile your kernel with your own PA-RISC box. But on old systems,
you may prefer to use another - faster - computer to compile your kernel. We
will see the two alternatives. Whichever you choose, you need at least
gcc-3.0.
Note By the time this howto is released, only gcc-3.0.X was able to build
working kernels. There is a bug in more recent versions that makes the
box crash when network activity occurs.
-----------------------------------------------------------------------------
6.1.1. native build
Since Debian is the only distribution supporting PA-RISC architecture, if
you want to use the Super Cow powers, you need to have some basic knowledge
about the Debian packaging system. We will explain here how to quickly get a
gcc compiler ready on your PA-RISC box.
-----------------------------------------------------------------------------
6.1.1.1. apt-get and friends
apt-get is a simple command line utility that manages Debian package system.
Gustavo Noronha Silva wrote the [http://www.debian.org/doc/manuals/apt-howto
/] APT HOWTO that you should read for sharper details. Actually, we just want
to build a kernel, so we will tell you the bare minimum needed to do that.
First, setup your sources.list in order to fetch the needed archives from the
Internet. Here is a sample configuration for /etc/apt/sources.list, using a
German Debian mirror :
# Binary packages
deb http://ftp.de.debian.org/debian unstable main contrib non-free
# non-US packages
deb http://ftp.de.debian.org/debian-non-US unstable/non-US main non-free contrib
# source packages
deb-src http://ftp.de.debian.org/debian unstable main contrib non-free
# non-US source packages
deb-src http://ftp.de.debian.org/debian-non-US unstable/non-US main contrib non-free
-----------------------------------------------------------------------------
6.1.1.2. update your gcc
If you are using your own PA-RISC box, you only need the good old GCC
compiler. We recommend to keep it up-to-date with the latest version uploaded
by the developers.
bash# apt-get update
bash# apt-get upgrade
If you do not want to upgrade all your system, according to the package
description of kernel-source, you need to get those packages updated :
* binutils
* fileutils
* gcc
* libc-dev
* make
When this is done, you can proceed to the kernel settings.
-----------------------------------------------------------------------------
6.1.2. cross compiled build
In this kernel build method, everything depends on the architecture of your
building machine. For x86 computers, you can download a ready-to-use cross
compiler archive on the PA/Linux FTP server. You can also find some "exotic"
(like for MacOS X) cross-compilers archives on the PA/Linux ESIEE Team
website. For other architectures or if you want to compile your own
toolchain, please refer to [http://www.parisc-linux.org/toolchain/
PARISC-Linux-XC-HOWTO.html] Carlos O'Donell's HOWTO.
Important As there is not yet a 64bit userspace on HP-PA, you have to
cross-compile 64bit kernel even if you are building on a 64bit
PA-RISC box. You can get unofficial debs for hppa64 compilers and
binutils at [ftp://ftp.parisc-linux.org/unofficial-debs/] ftp://
ftp.parisc-linux.org/unofficial-debs/. See [http://
www.parisc-linux.org/] PA-RISC Linux Website for details.
-----------------------------------------------------------------------------
6.2. Kernel configuration
If you want to take advantage of the latest kernel improvements, we suggest
you to retrieve it from the official [http://cvs.parisc-linux.org/] PA-RISC/
Linux CVS. You can of course either download it from [http://www.kernel.org/]
http://www.kernel.org/, or use the Debian package, but we will focus on a
fresh CVS tree.
The best way to obtain appreciable performances is to get a well configured
kernel. For the PA-RISC platform, make oldconfig is a kind of default setup.
If you want to make your own kernel, the first step is to know what hardware
you have. The best way to grab useful info is to look at your box and find a
maximum of data (model name, partnumber, chipsets, and so on). If you have
already booted your box, you can take a look at dmesg output. Then, go to the
official hardware database or to the [http://partsurfer.hp.com/] HP
partsurfer website.
Once you know what is inside your box and what you want to do with it, just
run make menuconfig or another config command. Here is a brief list of
architecture dependent menus for 2.4 kernels. You should take a look at them,
to see if the values set correspond to your hardware :
Note Remenber that make oldconfig is a good base to start with, since it
works for almost all machines.
* Processor type - indicates your CPU model
* General options - tells you what is going to be enabled in your kernel
(U2/Uturn, USC/GSC/HSC, Lasi, Wax, Dino, LBA/Elroy, SuperIO)
* Parallel port support - enables/disables the Lasi/ASP parport
* SCSI support - check there for your SCSI chipset (Lasi, Zalon, NCR/
SYM53C8XX or other)
* Network device support - is used to set your network card (Lasi,
Tulip...)
* Character devices - defines your I/O capabilities (Lasi, Dino, PDC see
Section 6.2.3)
* HIL Support - useful if you have a HIL controller. See below Section
6.2.1.
* Console drivers - is directly related to your console mode (STI console
or STI framebuffer)
* Sound - enables/disables the Harmony driver
As you see, menus specifically concerned by PA-RISC hardware are not that
numerous, but there are lots of dependencies between them. Now, you must
configure the kernel accordingly to what you plan to use this box for. Here
is a list of some menus you should be going through to configure additional
functionnalities you might want :
* General setup - is responsible for binary formats handled by the kernel.
You need ELF, and can try SOM (support for HP/UX binaries. It *might*
work with some static executables).
* Block devices - sets the ramdisk and loopback support. You probably won't
use them.
* ATA/IDE/MFM/RLL support - You will need to check this to enable IDE. See
Section 6.2.4
* File Systems/Network File Systems - is where to set EXT3 or NFS support
* USB support - If you have enabled SuperIO and want USB, look there
Section 6.2.2
Note At the time this HOWTO was written, there was no floppy drive support;
and what's more, it was not expected to have one any day.
When you're done with it, save your kernel configuration. Everything is
written in the .config file. You should back it up because a make distclean
will remove it. At this very stage, you can do make dep vmlinux and if
everything goes fine, you will have a new kernel in a couple of minutes.
Here follows brief information about specific hardware configurations.
-----------------------------------------------------------------------------
6.2.1. HIL Support
Since kernel-2.4.18-pa45, there is a full HIL support, for mice, tablets and
keyboards. It is based on the Linux Input Driver model. See the [http://
www.parisc-linux.org/faq/] PA-RISC/Linux FAQ and the [http://
lists.parisc-linux.org/pipermail/parisc-linux/2002-June/016757.html] mail
posted on the mailing list by Helge Deller. Here is what it says :
1. Make sure you have a 2.4.18-pa45 or higher kernel source.
2. Look at your kernel configuration for the following options :
CONFIG_INPUT=y
CONFIG_INPUT_KEYBDEV=y
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_EVDEV=y
CONFIG_INPUT_SERIO=y
CONFIG_HIL=y
CONFIG_HP_SDC=y
CONFIG_HIL_MLC=y
CONFIG_HP_SDC_MLC=y
CONFIG_HIL_KBD=y
CONFIG_HIL_PTR=y
Note There is no more CONFIG_HIL_KBD_BASIC.
3. On your target system, check that the following devices are available :
/dev/input/mice
/dev/input/mouseX
/dev/input/eventX
If they are not yet present, create them as root by running :
bash# cd /dev; ./MAKEDEV input
4. Configure gpm with the following options in /etc/gpm.conf :
device=/dev/input/mice
type=imps2
5. Here is a sample /etc/X11/XF86Config-4 :
Section "InputDevice"
Identifier "HIL Keyboard"
Driver "keyboard"
Option "CoreKeyboard"
EndSection
Section "InputDevice"
Identifier "HIL Mouse"
Driver "mouse"
Option "CorePointer"
Option "Device" "/dev/input/mice"
Option "Protocol" "ImPS/2"
Option "ZAxisMapping" "4 5"
EndSection
Section "ServerLayout"
Identifier "Default Layout"
Screen "Default Screen"
InputDevice "HIL Keyboard"
InputDevice "HIL Mouse"
EndSection
You can also download a sample XF86Config-4 here : [ftp://
ftp.parisc-linux.org/XFree86/XF86Config-4] ftp://ftp.parisc-linux.org/
XFree86/XF86Config-4, adjust color depth and resolution, and put it in
your /etc/X11/.
-----------------------------------------------------------------------------
6.2.2. USB Support
USB support on HP-PA is still experimental, therefore it is only proposed as
modules in default kernel configuration. We have tried to install a B2000
with builtin USB support, both 32 and 64bit, and it worked fine, despite some
keyboard problems. Don't worry, nothing critical : the range of keys located
between the main part of the keyboard (the letters, backspace, enter...) and
the numeric pad are spoiled. They do not behave as expected at all.
Tip You can use the numeric pad as arrow keys : when NumLock is not
activated, it behaves as a navigation pad. e.g. 8 is Up Arrow, 4 is Left
Arrow and so on.
1. Make sure you have a 2.4.18 or higher kernel source.
2. Look at your kernel configuration for the following options :
CONFIG_SUPERIO=y
CONFIG_HOTPLUG=y
CONFIG_INPUT=y
CONFIG_INPUT_KEYBDEV=y
CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
CONFIG_INPUT_EVDEV=y
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_OHCI=y
CONFIG_HID=y
3. On your target system, check that the following devices are available :
/dev/input/mice
/dev/input/mouseX
/dev/input/eventX
If they are not yet present, create them as root by running :
bash# cd /dev; ./MAKEDEV input
4. Configure gpm with the following options in /etc/gpm.conf :
device=/dev/input/mice
type=imps2
5. The XF86-Config-4 is similar to the HIL, as it is also using the Linux
Input Driver.
-----------------------------------------------------------------------------
6.2.3. PDC Console Support
PDC Console has been improved by Richard Hirst in pa37 kernel, though it is
still a very experimental feature. It is expected to provide adequate PDC
Console support to E- and K-Class machines. Feedback would be really
appreciated.
Now follow these steps to get it to work :
1. Make sure you have a 2.4.18-pa37 or higher kernel source.
2. Look at your kernel configuration for the following options :
CONFIG_SERIAL_CONSOLE=y
CONFIG_SERIAL_GSC=y
CONFIG_SERIAL_NONSTANDARD=y
CONFIG_PDC_CONSOLE=y
3. On your target system, check that the following devices are available :
/dev/ttyB0
If they are not yet present, create them as root by running :
bash# cd /dev; ./MAKEDEV ttyB0
Note It needs a recent MAKEDEV package to be created this way. By the
time this HOWTO was written, such a package could only be found on
netinst ISO provided at [http://www.pateam.org/download.html] http:/
/www.pateam.org/download.html.
4. Now you can boot your system, taking care that PALO uses console=ttyB0.
-----------------------------------------------------------------------------
6.2.4. IDE Devices Support
There is nothing really special about IDE support. You have to check that
your IDE Chipset is supported by the kernel. A common chipset found on
PA-RISC hardware is NS87415. You can find it on B2000, J5000 and C3000 for
instance. You will need IDE support to use some CD devices.
Here is an example to get IDE to work with this chipset :
1. Make sure you have a recent kernel source.
2. Look at your kernel configuration for the following options :
CONFIG_IOMMU_CCIO=y
CONFIG_PCI=y
CONFIG_PCI_LBA=y
CONFIG_IOSAPIC=y
CONFIG_IOMMU_SBA=y
CONFIG_SUPERIO=y
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_NS87415=y
3. On your target system, check that the following devices are available :
/dev/hd*
If they are not yet present, create them as root by running :
bash# cd dev; ./MAKEDEV hda hdb hdc hdd hde
Note It needs a recent MAKEDEV package to be created this way. By the
time this HOWTO was written, such a package could only be found on
netinst ISO provided at [http://www.pateam.org/download.html] http:/
/www.pateam.org/download.html.
Note Of course we didn't mention much of the non architecture independant
options. Moreover, the above settings may vary depending on your
hardware. This is just an example.
-----------------------------------------------------------------------------
6.3. Kernel installation
If you have made a native build on the box you wish to install, you can
setup the new kernel as follows : within the kernel source tree linux/, as
root do a :
bash# cp vmlinux /boot/vmlinux-[kernelversion]
bash# cp System.map /boot/System.map-[kernelversion]
bash# cp .config /boot/config-[kernelversion]
Though it is not mandatory, we suggest you to replace [kernelversion] by the
version of the kernel you built, e.g. : vmlinux-2.4.18-pa44. This will help
you dealing with multiple kernel versions on the same machine. The same
applies to .config. It is not needed to have a working kernel, though it
might be very helpful when configuring a new one. Now, do a cd /boot, make
sure that vmlinux is a symbolic link to another file, as in the following
example :
bash# ls -l vmlinux
lrwxrwxrwx 1 root root 35 Jun 23 01:38 vmlinux -> vmlinux-2.4.18-64-SMP
Make sure to remember the name of the kernel actually running on your box if
ever the new one won't work properly. You are now able to ask PALO to boot on
it if needed (see Chapter 4 for more information). Now do the following :
bash# rm -f vmlinux
bash# ln -s vmlinux-[kernelversion] vmlinux
bash# sync
If you want to boot from network you can forget all this, as you will need to
set PALO as explained in the Section 4.3, and run make palo to create the
bootable lifimage.
If you have made a cross-compiled build or built a kernel on a PA box which
is not the one you wish to install, you have to find a way to put vmlinux,
System.map and .config in /boot as mentionned before. You can use the network
(like ftp) or a CD to do so, or even direct copy to the hard disk drive.
-----------------------------------------------------------------------------
Chapter 7. Windows?? 2k server boot howto
This chapter is mainly a copy of Jeremy Drake's Windows?? 2k server boot
howto.
-----------------------------------------------------------------------------
7.1. Setup your DHCP server
Like for the UNIX/Linux based approach, you need several information and
data before setting everything. First of all, you need the MAC address of
your PA-RISC box. Please read these instructions. You are going to need a
lifimage file. Please read these instructions.
Then, you have to enable DHCP service on your Windows?? 2k box. You can do
that by going into the Control Panel then Add/remove programs then Windows
components and finally Networking Services. There you will ask for Dynamic
Host Configuration Protocol (DHCP).
You need to setup the DHCP service now. Launch the DHCP admin tool by going
into the Conttrol Panel, Admin Tools and DHCP.
* Expand your server tree.
* Right click on Reservations. Select "New Reservation...".
* For reservation name, I put my workstation's host name. Enter an unused
IP address. Enter the PA-RISC box' mac address (no delimiters, just the
hex number). Select "Both" for whether it should be bootp or dhcp. Click
"Ok" to close this window.
* Find your new reservation at the bottom of the list under Reservations
and click it.
* Right click "Configure Options..."
* It should have inherited your server's default options, so I won't cover
setting router, dns, wins and lease length.
* Scroll down the list of options to 066 "Boot Server Host Name". Check the
box next to option 066. Enter your tftp server's ip address because I
don't trust DNS to work in IPL.
* Check option 067 "Bootfile Name" and enter the name of the lifimage.
Generally, lifimage is a good choice here.
* Click "Ok" and your dhcp server is ready !
-----------------------------------------------------------------------------
7.2. Get your TFTP server
To get the network boot process operational, you need the TFTP service that
provides the basic file system at boot time. Get Tftpd from [http://
tftpd32.jounin.net/] http://tftpd32.jounin.net/. You must download the latest
version in zip format. Unzip it and store it in your favorite place. Then,
you must setup the monster.
* Run tftpd32.
* Click the "browse" button
* Browse to where you put your lifimage, highlight it and click "Ok".
* Make sure the IP address below the directory is the one you gave to your
PA-RISC box.
* Leave tftpd32 running. The tftp server only runs when the gui is
displayed.
If you want to run it as a NT service, you have to download a Microsoft??
program. Please refer to the \ Tftpd32's FAQ.
-----------------------------------------------------------------------------
7.3. Launch your netboot
Now, you are fully set up to try the boot of your PA-RISC box via network.
You can follow these instructions.
If you have any trouble, start by looking at those points and then ask the
PA/Linux mailing list.
* Settings on the DHCP server (verify the PA-RISC MAC address is correct).
* Your dhcp server is on the same physical network segment as the PA-RISC
box.
* The network connection of the 2 boxes.
* Try to tcpdump while you are "boot lan"ing the PA-RISC box.
-----------------------------------------------------------------------------
Chapter 8. HOWTO contributors
The following people contributed or reviewed this HOWTO in one way or
another.
For Deb's version :
* David Alexander deVries <adevries@thepuffingroup.com>
* Philip Imperial Schwan <pschwan@thepuffingroup.com>
For Thomas' version :
* Michael Damaschke <sps01@uni-koeln.de> Thanks for your example about PALO
* Helge Deller <deller@gmx.de>
* Jeremy Drake <jeremyd@apptechsys.com> Thanks for your Windows?? 2k server
boot howto
* Grant Grundler <grundler@parisc-linux.org>
* Richard Hirst <rhirst@parisc-linux.org>
For Thibaut's version :
* Matthieu Delahaye <delahaym@esiee.fr>
* Helge Deller <deller@gmx.de>
* Grant Grundler <grundler@parisc-linux.org>
* Richard Hirst <rhirst@parisc-linux.org>
* Clement Moyroud <moyroudc@esiee.fr>
* Matthew Wilcox <matthew@wil.cx>
Glossary
This is a brief glossary of the PA-RISC specific terminology. You can find a
more detailed one at [http://www.parisc-linux.org/glossary/] http://
www.parisc-linux.org/glossary/.
BOOT_ADMIN
This a command line utility stored in the boot ROM of the PA box, which
is used to configure the computer during early boot sequence. It is a
part of the PA-RISC machine's firmware.
Guardian Service Processor (GSP)
The GSP is a console subsystem present on certain PA-RISC systems, which
provides several features such as remote console, UPS management, system
low level control.
High Priority Machine Check (HPMC)
Fatal system error. Processor-Dependent Code (PDC) saves machine state in
the Processor Internal Memory (PIM).
HP-PA
'HP-PA' (sometimes 'hppa') is the short way to refer to HP PA-RISC
architecture. It's real meaning is : 'Hewlett Packard Precision
Architecture'. It is used for instance by [http://www.debian.org/ports/
hppa/] Debian and [http://www.openbsd.org/hppa.html] OpenBSD to point out
their ports.
Initial Program Loader (IPL)
It is the HP standardized system bootstrap responsible for loading the
operating system's kernel on PA-RISC systems. It can be launched from the
BOOT_ADMIN.
See Also: BOOT_ADMIN.
Initial System Loader (ISL)
ISL is the executable that brings you into BOOT_ADMIN.
See Also: Initial Program Loader (IPL).
Logical Interchange Format (LIF)
This is a HP mass-storage format used for exchanging files among HP
computer systems. It basically contains a header (identifying it as a LIF
volume) and a directory of fixed size containing the files. The size of
the directory is fixed when the volume is created, which explains many
thingss about the way PALO works !
lifimage
It is the name contraction of 'LIF image', which is indeed a file which
respond to 'LIF' standard. It can be seen as the equivalent of an 'ISO'
file, having the 'LIF' format instead of 'ISO9660'.
See Also: Logical Interchange Format (LIF).
Low Priority Machine Check (LPMC)
Generally a recoverable system error.
PA-RISC
PA stands for Precision Architecture. It is the name of two generations
of HP processors. They are classified as PA-RISC 1.X and PA-RISC 2.0. But
a system based on a PA-RISC processor is commonly called a HP-PA box.
See Also: HP-PA.
PA LOader (PALO)
PALO is the PA/Linux kernel LOader. It was designed by Paul Bame as a
LILO equivalent for the PA-RISC architecture.
Processor-Dependent Code (PDC)
It is the firmware that handles all processor-dependent functionalities,
including initialization and self-test procedures. Once it has done this,
it passes control to the ISL.
See Also: Initial System Loader (ISL).
Processor Internal Memory (PIM)
Machine state is saved here for HPMC, LPMC, and TOC's. See PDC_PIM in
"PDC Procedures" chapter of PA I/O ACD.
See Also: Initial System Loader (ISL).
netinst
This is not a PA-RISC specific term, though it needs explanations.
'Network Install', also known as 'netinst', are small ISOs containing
everything you need to boot a computer and install it from network. They
are based on the [http://www.debian.org/] Debian distribution.
SuckyIO
(added by special request) National Semiconductor PC87560UBD, aka "
SuperIO". Provides IDE, USB 1.1, Floppy Disk Controller, parallel port, 2
serial ports, UIR (Infrared), etc. But since National denies the
existence of this chip and HP was the only client for this buggy PoS, the
name "SuckyIO" has stuck.
SuperIO
Official term for "SuckyIO"
See Also: SuckyIO.
Standard Text Interface (STI)
It defines a standardized way to access the graphic subsystem on HP-PA.
Transfer Of Control (TOC)
Under HP/UX it would make a crash dump and reset the box. It can also be
called from the GSP. Under Linux, it will save the registers and reset,
saved registers will be accessible through PDC.
-----------------------------------------------------------------------------
Bibliography
These documents might prove helpful to understand the present one, or to open
new horizons :
[Raymond 2000] E. S. Raymond, 2000, [http://www.tldp.org/HOWTO/
Installation-HOWTO/index.html] Installation-HOWTO .
How to obtain and install Linux software. It is the first document which a
new Linux user should read to get started.
[Maor 1999] O. Maor, 1999, [http://www.tldp.org/HOWTO/mini/
NFS-Root-Client-mini-HOWTO/index.html] NFS-Root-Client Mini-HOWTO .
How to create client root directories on a server that is using NFS Root
mounted clients.
[Kostyrka 1997] A. Kostyrka, 1997, [http://www.tldp.org/HOWTO/mini/
NFS-Root.html] NFS-Root Mini-HOWTO .
How to setup a 'disk-less' Linux workstation, which mounts its root
filesystem via NFS.
[Harris et al. 1997] T. Harris and K. Koehntopp, 1997, [http://www.tldp.org
/HOWTO/mini/Partition/index.html] Linux Partition HOWTO .
Teaches you how to plan and layout disk space for your Linux system.
[Dev 1998] A. Dev, 1998, [http://www.tldp.org/HOWTO/CVS-RCS-HOWTO.html]
CVS-RCS-HOWTO .
This document is a "practical guide" to very quicly setup CVS/RCS source code
control system.
[Noronha Silva 2001] G. Noronha Silva, 2001, [http://www.debian.org/doc/
manuals/apt-howto/] APT HOWTO .
Will help you understand how the Debian package management utility, APT,
works.
[O'Donell 2002] C. O'Donell, 2002, [http://www.parisc-linux.org/toolchain/
PARISC-Linux-XC-HOWTO.html] The PARISC-Linux Cross Compiler HOWTO .
This is a semi-detailed guide for building a cross compiler toolchain
targetting HP PA-RISC systems.
[Cornec 1997] B. Cornec, 1997, [http://www.tldp.org/HOWTO/HP-HOWTO/
index.html] HP HOWTO .
Describes the use of products available in the Hewlett-Packard (HP) catalog
with Linux and some free software.
[Perens et al. 1996] B. Perens, S. Rudolph, I. Grobman, J. Treacy, and A. Di
Carlo, 1996, [http://ftp.debian.org/debian/dists/woody/main/disks-hppa/
current/doc/index.en.html] Debian GNU/Linux 3.0 Installation Documentation
Index .
Will help you to install and configure your Debian GNU/Linux system.
[Brouwer 1993] A. Brouwer, 1993, [http://www.tldp.org/HOWTO/
Keyboard-and-Console-HOWTO.html] The Linux keyboard and console HOWTO .
This note contains some information about the Linux keyboard and console, and
the use of non-ASCII characters.
