Sophie: howto-text-en-2007-4mdv2010.0 noarch

howto-text-en-2007-4mdv2010.0.noarch.rpm

HOWTO: Multi Disk System Tuning
Stein Gjoen, sgjoen@nyx.net
v0.33a, 20 May 2002

This document describes how best to use multiple disks and partitions
for a Linux system. Although some of this text is Linux specific the
general approach outlined here can be applied to many other multi
tasking operating systems.
______________________________________________________________________

Table of Contents

1. Introduction

1.1 Copyright
1.2 Disclaimer
1.3 News
1.4 Credits
1.5 Translations

2. Structure

2.1 Logical structure
2.2 Document structure
2.3 Reading plan

3. Drive Technologies

3.1 Drives
3.2 Geometry
3.3 Media
3.3.1 Magnetic Drives
3.3.2 Optical Drives
3.3.3 Solid State Drives
3.4 Interfaces
3.4.1 MFM and RLL
3.4.2 ESDI
3.4.3 IDE and ATA
3.4.4 EIDE, Fast-ATA and ATA-2
3.4.5 Ultra-ATA
3.4.6 Serial-ATA
3.4.7 ATAPI
3.4.8 SCSI
3.5 Cabling
3.6 Host Adapters
3.7 Multi Channel Systems
3.8 Multi Board Systems
3.9 Speed Comparison
3.9.1 Controllers
3.9.2 Bus Types
3.10 Benchmarking
3.11 Comparisons
3.12 Future Development
3.13 Recommendations

4. File System Structure

4.1 File System Features
4.1.1 Swap
4.1.2 Temporary Storage (/tmp and /var/tmp)
4.1.3 Spool Areas (/var/spool/news and /var/spool/mail)
4.1.4 Home Directories (/home)
4.1.5 Main Binaries ( /usr/bin and /usr/local/bin)
4.1.6 Libraries ( /usr/lib and /usr/local/lib)
4.1.7 Boot
4.1.8 Root
4.1.9 DOS etc.
4.2 Explanation of Terms
4.2.1 Speed
4.2.2 Reliability
4.2.3 Files

5. File Systems

5.1 General Purpose File Systems
5.1.1 minix
5.1.2 xiafs and extfs
5.1.3 ext2fs
5.1.4 ext3fs
5.1.5 ufs
5.1.6 efs
5.1.7 XFS
5.1.8 reiserfs
5.1.9 enh-fs
5.1.10 Tux2 fs
5.2 Microsoft File Systems
5.2.1 fat
5.2.2 fat32
5.2.3 vfat
5.2.4 ntfs
5.3 Logging and Journaling File Systems
5.4 Read-only File Systems
5.4.1 High Sierra
5.4.2 iso9660
5.4.3 Rock Ridge
5.4.4 Joliet
5.4.5 Trivia
5.4.6 UDF
5.5 Networking File Systems
5.5.1 NFS
5.5.2 AFS
5.5.3 Coda
5.5.4 nbd
5.5.5 enbd
5.5.6 GFS
5.6 Special File Systems
5.6.1 tmpfs and swapfs
5.6.2 userfs
5.6.3 devfs
5.6.4 smugfs
5.7 File System Recommendations

6. Technologies

6.1 RAID
6.1.1 SCSI-to-SCSI
6.1.2 PCI-to-SCSI
6.1.3 Software RAID
6.1.4 RAID Levels
6.2 Volume Management
6.3 Linux md Kernel Patch
6.4 Compression
6.5 ACL
6.6 cachefs
6.7 Translucent or Inheriting File Systems
6.8 Physical Track Positioning
6.8.1 Disk Speed Values
6.9 Yoke
6.10 Stacking
6.11 Recommendations

7. Other Operating Systems

7.1 DOS
7.2 Windows
7.3 OS/2
7.4 NT
7.5 Windows 2000
7.6 Sun OS
7.6.1 Sun OS 4
7.6.2 Sun OS 5 (aka Solaris)
7.7 BeOS

8. Clusters
9. Mount Points

10. Considerations and Dimensioning

10.1 Home Systems
10.2 Servers
10.2.1 Home Directories
10.2.2 Anonymous FTP
10.2.3 WWW
10.2.4 Mail
10.2.5 News
10.2.6 Others
10.2.7 Server Recommendations
10.3 Pitfalls

11. Disk Layout

11.1 Selection for Partitioning
11.2 Mapping Partitions to Drives
11.3 Sorting Partitions on Drives
11.4 Optimizing
11.4.1 Optimizing by Characteristics
11.4.2 Optimizing by Drive Parallelising
11.5 Compromises

12. Implementation

12.1 Checklist
12.2 Drives and Partitions
12.3 Partitioning
12.4 Repartitioning
12.5 Microsoft Partition Bug
12.6 Multiple Devices (md)
12.7 Formatting
12.8 Mounting
12.9 fstab
12.10 Mount options
12.11 Recommendations

13. Maintenance

13.1 Backup
13.2 Defragmentation
13.3 Deletions
13.4 Upgrades
13.5 Recovery
13.6 Rescue Disk

14. Advanced Issues

14.1 Hard Disk Tuning
14.2 File System Tuning
14.3 Spindle Synchronizing

15. Troubleshooting

15.1 During Installation
15.1.1 Locating Disks
15.1.2 Formatting
15.2 During Booting
15.2.1 Booting fails
15.2.2 Getting into Single User Mode
15.3 During Running
15.3.1 Swap
15.3.2 Partitions

16. Further Information

16.1 News groups
16.2 Mailing Lists
16.3 HOWTO
16.4 Mini-HOWTO
16.5 Local Resources
16.6 Web Pages
16.7 Search Engines

17. Getting Help

18. Concluding Remarks

18.1 Coming Soon
18.2 Request for Information
18.3 Suggested Project Work

19. Questions and Answers

20. Bits and Pieces

20.1 Swap Partition: to Use or Not to Use
20.2 Mount Point and /mnt
20.3 Power and Heating
20.4 Deja
20.5 Crash Recovery

21. Appendix A: Partitioning Layout Table: Mounting and Linking

22. Appendix B: Partitioning Layout Table: Numbering and Sizing

23. Appendix C: Partitioning Layout Table: Partition Placement

24. Appendix D: Example: Multipurpose Server

25. Appendix E: Example: Mounting and Linking

26. Appendix F: Example: Numbering and Sizing

27. Appendix G: Example: Partition Placement

28. Appendix H: Example II

29. Appendix I: Example III: SPARC Solaris

30. Appendix J: Example IV: Server with 4 Drives

31. Appendix K: Example V: Dual Drive System

32. Appendix L: Example VI: Single Drive System

33. Appendix M: Disk System Documenter

______________________________________________________________________

1. Introduction

For unclear reasons this brand new release is codenamed the Taylor3
release.

New code names will appear as per industry standard guidelines to
emphasize the state-of-the-art-ness of this document.

This document was written for two reasons, mainly because I got hold
of 3 old SCSI disks to set up my Linux system on and I was pondering
how best to utilise the inherent possibilities of parallelizing in a
SCSI system. Secondly I hear there is a prize for people who write
documents...

This is intended to be read in conjunction with the Linux Filesystem
Structure Standard (FSSTND). It does not in any way replace it but
tries to suggest where physically to place directories detailed in the
FSSTND, in terms of drives, partitions, types, RAID, file system (fs),
physical sizes and other parameters that should be considered and
tuned in a Linux system, ranging from single home systems to large
servers on the Internet.

The followup to FSSTND is called the Filesystem Hierarchy Standard
(FHS) and covers more than Linux alone. FHS versions 2.0, 2.1 and 2.2
have been released but there are still a few issues to be dealt with.
Many recent distributions are now aiming for FHS compliance.

It is also a good idea to read the Linux Installation guides
thoroughly and if you are using a PC system, which I guess the
majority still does, you can find much relevant and useful information
in the FAQs for the newsgroup comp.sys.ibm.pc.hardware especially for
storage media.

This is also a learning experience for myself and I hope I can start
the ball rolling with this HOWTO and that it perhaps can evolve into a
larger more detailed and hopefully even more correct HOWTO.

First of all we need a bit of legalese. Recent development shows it is
quite important.

1.1. Copyright

This document is Copyright 1996 Stein Gjoen. Permission is granted to
copy, distribute and/or modify this document under the terms of the
GNU Free Documentation License, Version 1.1 or any later version
published by the Free Software Foundation with no Invariant Sections,
no Front-Cover Texts, and no Back-Cover Texts.

If you have any questions, please contact <{linux-
howto@metalab.unc.edu}>

1.2. Disclaimer

Use the information in this document at your own risk. I disavow any
potential liability for the contents of this document. Use of the
concepts, examples, and/or other content of this document is entirely
at your own risk.

All copyrights are owned by their owners, unless specifically noted
otherwise. Use of a term in this document should not be regarded as
affecting the validity of any trademark or service mark.

Naming of particular products or brands should not be seen as
endorsements.

You are strongly recommended to take a backup of your system before
major installation and backups at regular intervals.
1.3. News

This is a major upgrade featuring a new copyright statement that is
intended to be Debian compliant and allow for inclusion in their
distribution. A number of mistakes are corrected and new features
added such as descriptions of recent ATA features and more.

On the development front people are concentrating their energy towards
completing Linux 2.4 and until that is released there is not going to
be much news on disk technology for Linux.

Also now the document is available in postscript both for US letter as
well as European A4 formats.

The latest version number of this document can be gleaned from my plan
entry if you finger
<http://www.mit.edu:8001/finger?sgjoen@nox.nyx.net> my Nyx account.

Also, the latest version will be available on my web space on Nyx in a
number of formats:

· HTML <http://www.nyx.net/~sgjoen/disk.html>.

· plain ASCII text <http://www.nyx.net/~sgjoen/disk.txt> (ca. 6200
lines).

· compressed postscript US letter format
<http://www.nyx.net/~sgjoen/disk-US.ps.gz> (ca. 90 pages).

· compressed postscript European A4 format
<http://www.nyx.net/~sgjoen/disk-A4.ps.gz> (ca. 85 pages).

· SGML source <http://www.nyx.net/~sgjoen/disk.sgml> (ca. 260 KB).

A European mirror of the Multi Disk HOWTO
<http://home.online.no/~ggjoeen/stein/disk.html> just went on line.

1.4. Credits

In this version I have the pleasure of acknowledging even more people
who have contributed in one way or another:

ronnej (at ) ucs.orst.edu
cm (at) kukuruz.ping.at
armbru (at) pond.sub.org
R.P.Blake (at) open.ac.uk
neuffer (at) goofy.zdv.Uni-Mainz.de
sjmudd (at) redestb.es
nat (at) nataa.fr.eu.org
sundbyk (at) oslo.geco-prakla.slb.com
ggjoeen (at) online.no
mike (at) i-Connect.Net
roth (at) uiuc.edu
phall (at) ilap.com
szaka (at) mirror.cc.u-szeged.hu
CMckeon (at) swcp.com
kris (at) koentopp.de
edick (at) idcomm.com
pot (at) fly.cnuce.cnr.it
earl (at) sbox.tu-graz.ac.at
ebacon (at) oanet.com
vax (at) linkdead.paranoia.com
tschenk (at) theoffice.net
pjfarley (at) dorsai.org
jean (at) stat.ubc.ca
johnf (at) whitsunday.net.au
clasen (at) unidui.uni-duisburg.de
eeslgw (at) ee.surrey.asc.uk
adam (at) onshore.com
anikolae (at) wega-fddi2.rz.uni-ulm.de
cjaeger (at) dwave.net
eperezte (at) c2i.net
yesteven (at) ms2.hinet.net
cj (at) samurajdata.se
tbotond (at) netx.hu
russel (at) coker.com.au
lars (at) iar.se
GALLAGS3 (at) labs.wyeth.com
morimoto (at) xantia.citroen.org
shulegaa (at) gatekeeper.txl.com
roman.legat (at) stud.uni-hannover.de
ahamish (at) hicks.alien.usr.com
hduff2 (at) worldnet.att.net
mbaehr (at) email.archlab.tuwien.ac.at
adc (at) postoffice.utas.edu.au
pjm (at) bofh.asn.au
jochen.berg (at) ac.com
jpotts (at) us.ibm.com
jarry (at) gmx.net
LeBlanc (at) mcc.ac.uk
masy (at) webmasters.gr.jp
karlheg (at) hegbloom.net
goeran (at) uddeborg.pp.se
wgm (at) telus.net

1.5. Translations

Special thanks go to nakano (at) apm.seikei.ac.jp for doing the
Japanese translation <http://www.linux.or.jp/JF/JFdocs/Multi-Disk-
HOWTO.html>, general contributions as well as contributing an example
of a computer in an academic setting, which is included at the end of
this document.

There are now many new translations available and special thanks go to
the translators for the job and the input they have given:

· German Translation <http://www.linuxdoc.org/> by chewie (at)
nuernberg.netsurf.de

· Swedish Translation <http://www.swe-doc.linux.nu> by jonah (at)
swipnet.se

· French Translation <http://www.lri.fr/~loisel/howto/> by
Patrick.Loiseleur (at) lri.fr

· Chinese Translation <http://www.linuxdoc.org/> by yesteven (at )
ms2.hinet.net

· Italian Translation <http://www.pluto.linux.it/ildp/HOWTO/Multi-
Disk-HOWTO.html> by bigpaul (at) flashnet.it

ICP Vortex is gratefully acknowledges for sending in-depth information
on their range of RAID controllers.

Also DPT is acknowledged for sending me documentation on their
controllers as well as permission to quote from the material. These
quotes have been approved before appearing here and will be clearly
labelled. No quotes as of yet but that is coming.

Not many still, so please read through this document, make a
contribution and join the elite. If I have forgotten anyone, please
let me know.

New in this version is an appendix with a few tables you can fill in
for your system in order to simplify the design process.

Any comments or suggestions can be mailed to my mail address on Nyx:
sgjoen@nyx.net.

So let's cut to the chase where swap and /tmp are racing along hard
drive...

2. Structure

As this type of document is supposed to be as much for learning as a
technical reference document I have rearranged the structure to this
end. For the designer of a system it is more useful to have the
information presented in terms of the goals of this exercise than from
the point of view of the logical layer structure of the devices
themselves. Nevertheless this document would not be complete without
such a layer structure the computer field is so full of, so I will
include it here as an introduction to how it works.

It is a long time since the mini in mini-HOWTO could be defended as
proper but I am convinced that this document is as long as it needs to
be in order to make the right design decisions, and not longer.

2.1. Logical structure

This is based on how each layer access each other, traditionally with
the application on top and the physical layer on the bottom. It is
quite useful to show the interrelationship between each of the layers
used in controlling drives.

In the above diagram both volume management and RAID and concatenation
are optional layers. The 3 lower layers are in hardware. All parts
are discussed at length later on in this document.

2.2. Document structure

Most users start out with a given set of hardware and some plans on
what they wish to achieve and how big the system should be. This is
the point of view I will adopt in this document in presenting the
material, starting out with hardware, continuing with design
constraints before detailing the design strategy that I have found to
work well. I have used this both for my own personal computer at
home, a multi purpose server at work and found it worked quite well.
In addition my Japanese co-worker in this project have applied the
same strategy on a server in an academic setting with similar success.

Finally at the end I have detailed some configuration tables for use
in your own design. If you have any comments regarding this or notes
from your own design work I would like to hear from you so this
document can be upgraded.

2.3. Reading plan

Although not the biggest HOWTO it is nevertheless rather big already
and I have been requested to make a reading plan to make it possible
to cut down on the volume

Expert
(aka the elite). If you are familiar with Linux as well as disk
drive technologies you will find most of what you need in the
appendices. Additionally you are recommended to read the FAQ and
the ``Bits'n'pieces'' chapter.

Experienced
(aka Competent). If you are familiar with computers in general
you can go straight to the chapters on ``technologies'' and
continue from there on.

Newbie
(mostly harmless). You just have to read the whole thing.
Sorry. In addition you are also recommended to read all the
other disk related HOWTOs.

3. Drive Technologies

A far more complete discussion on drive technologies for IBM PCs can
be found at the home page of The Enhanced IDE/Fast-ATA FAQ
<http://thef-nym.sci.kun.nl/~pieterh/storage.html> which is also
regularly posted on Usenet News. There is also a site dedicated to
ATA and ATAPI Information and Software <http://ata-atapi.com>.

Here I will just present what is needed to get an understanding of the
technology and get you started on your setup.

3.1. Drives

This is the physical device where your data lives and although the
operating system makes the various types seem rather similar they can
in actual fact be very different. An understanding of how it works can
be very useful in your design work. Floppy drives fall outside the
scope of this document, though should there be a big demand I could
perhaps be persuaded to add a little here.

3.2. Geometry

Physically disk drives consists of one or more platters containing
data that is read in and out using sensors mounted on movable heads
that are fixed with respects to themselves. Data transfers therefore
happens across all surfaces simultaneously which defines a cylinder of
tracks. The drive is also divided into sectors containing a number of
data fields.

Drives are therefore often specified in terms of its geometry: the
number of Cylinders, Heads and Sectors (CHS).

For various reasons there is now a number of translations between

· the physical CHS of the drive itself

· the logical CHS the drive reports to the BIOS or OS

· the logical CHS used by the OS

Basically it is a mess and a source of much confusion. For more
information you are strongly recommended to read the Large Disk mini-
HOWTO

3.3. Media

The media technology determines important parameters such as
read/write rates, seek times, storage size as well as if it is
read/write or read only.

3.3.1. Magnetic Drives

This is the typical read-write mass storage medium, and as everything
else in the computer world, comes in many flavours with different
properties. Usually this is the fastest technology and offers
read/write capability. The platter rotates with a constant angular
velocity (CAV) with a variable physical sector density for more
efficient magnetic media area utilisation. In other words, the number
of bits per unit length is kept roughly constant by increasing the
number of logical sectors for the outer tracks.

Typical values for rotational speeds are 4500 and 5400 RPM, though
7200 is also used. Very recently also 10000 RPM has entered the mass
market. Seek times are around 10 ms, transfer rates quite variable
from one type to another but typically 4-40 MB/s. With the extreme
high performance drives you should remember that performance costs
more electric power which is dissipated as heat, see the point on
``Power and Heating''.

Note that there are several kinds of transfers going on here, and that
these are quoted in different units. First of all there is the
platter-to-drive cache transfer, usually quoted in Mbits/s. Typical
values here is about 50-250 Mbits/s. The second stage is from the
built in drive cache to the adapter, and this is typically quoted in
MB/s, and typical quoted values here is 3-40 MB/s. Note, however, that
this assumed data is already in the cache and hence for maximum
readout speed from the drive the effective transfer rate will decrease
dramatically.

3.3.2. Optical Drives

Optical read/write drives exist but are slow and not so common. They
were used in the NeXT machine but the low speed was a source for much
of the complaints. The low speed is mainly due to the thermal nature
of the phase change that represents the data storage. Even when using
relatively powerful lasers to induce the phase changes the effects are
still slower than the magnetic effect used in magnetic drives.

Today many people use CD-ROM drives which, as the name suggests, is
read-only. Storage is about 650 MB, transfer speeds are variable,
depending on the drive but can exceed 1.5 MB/s. Data is stored on a
spiraling single track so it is not useful to talk about geometry for
this. Data density is constant so the drive uses constant linear
velocity (CLV). Seek is also slower, about 100 ms, partially due to
the spiraling track. Recent, high speed drives, use a mix of CLV and
CAV in order to maximize performance. This also reduces access time
caused by the need to reach correct rotational speed for readout.

A new type (DVD) is on the horizon, offering up to about 18 GB on a
single disk.

3.3.3. Solid State Drives

This is a relatively recent addition to the available technology and
has been made popular especially in portable computers as well as in
embedded systems. Containing no movable parts they are very fast both
in terms of access and transfer rates. The most popular type is flash
RAM, but also other types of RAM is used. A few years ago many had
great hopes for magnetic bubble memories but it turned out to be
relatively expensive and is not that common.

In general the use of RAM disks are regarded as a bad idea as it is
normally more sensible to add more RAM to the motherboard and let the
operating system divide the memory pool into buffers, cache, program
and data areas. Only in very special cases, such as real time systems
with short time margins, can RAM disks be a sensible solution.

Flash RAM is today available in several 10's of megabytes in storage
and one might be tempted to use it for fast, temporary storage in a
computer. There is however a huge snag with this: flash RAM has a
finite life time in terms of the number of times you can rewrite data,
so putting swap, /tmp or /var/tmp on such a device will certainly
shorten its lifetime dramatically. Instead, using flash RAM for
directories that are read often but rarely written to, will be a big
performance win.

In order to get the optimum life time out of flash RAM you will need
to use special drivers that will use the RAM evenly and minimize the
number of block erases.

This example illustrates the advantages of splitting up your directory
structure over several devices.

Solid state drives have no real cylinder/head/sector addressing but
for compatibility reasons this is simulated by the driver to give a
uniform interface to the operating system.

3.4. Interfaces

There is a plethora of interfaces to chose from widely ranging in
price and performance. Most motherboards today include IDE interface
which are part of modern chipsets.

Many motherboards also include a SCSI interface chip made by Symbios
(formerly NCR) and that is connected directly to the PCI bus. Check
what you have and what BIOS support you have with it.

3.4.1. MFM and RLL

Once upon a time this was the established technology, a time when 20
MB was awesome, which compared to todays sizes makes you think that
dinosaurs roamed the Earth with these drives. Like the dinosaurs these
are outdated and are slow and unreliable compared to what we have
today. Linux does support this but you are well advised to think twice
about what you would put on this. One might argue that an emergency
partition with a suitable vintage of DOS might be fitting.

3.4.2. ESDI

Actually, ESDI was an adaptation of the very widely used SMD interface
used on "big" computers to the cable set used with the ST506
interface, which was more convenient to package than the 60-pin +
26-pin connector pair used with SMD. The ST506 was a "dumb" interface
which relied entirely on the controller and host computer to do
everything from computing head/cylinder/sector locations and keeping
track of the head location, etc. ST506 required the controller to
extract clock from the recovered data, and control the physical
location of detailed track features on the medium, bit by bit. It had
about a 10-year life if you include the use of MFM, RLL, and ERLL/ARLL
modulation schemes. ESDI, on the other hand, had intelligence, often
using three or four separate microprocessors on a single drive, and
high-level commands to format a track, transfer data, perform seeks,
and so on. Clock recovery from the data stream was accomplished at the
drive, which drove the clock line and presented its data in NRZ,
though error correction was still the task of the controller. ESDI
allowed the use of variable bit density recording, or, for that
matter, any other modulation technique, since it was locally generated
and resolved at the drive. Though many of the techniques used in ESDI
were later incorporated in IDE, it was the increased popularity of
SCSI which led to the demise of ESDI in computers. ESDI had a life of
about 10 years, though mostly in servers and otherwise "big" systems
rather than PC's.

3.4.3. IDE and ATA

Progress made the drive electronics migrate from the ISA slot card
over to the drive itself and Integrated Drive Electronics was borne.
It was simple, cheap and reasonably fast so the BIOS designers
provided the kind of snag that the computer industry is so full of. A
combination of an IDE limitation of 16 heads together with the BIOS
limitation of 1024 cylinders gave us the infamous 504 MB limit.
Following the computer industry traditions again, the snag was patched
with a kludge and we got all sorts of translation schemes and BIOS
bodges. This means that you need to read the installation
documentation very carefully and check up on what BIOS you have and
what date it has as the BIOS has to tell Linux what size drive you
have. Fortunately with Linux you can also tell the kernel directly
what size drive you have with the drive parameters, check the
documentation for LILO and Loadlin, thoroughly. Note also that IDE is
equivalent to ATA, AT Attachment. IDE uses CPU-intensive Programmed
Input/Output (PIO) to transfer data to and from the drives and has no
capability for the more efficient Direct Memory Access (DMA)
technology. Highest transfer rate is 8.3 MB/s.

3.4.4. EIDE, Fast-ATA and ATA-2

These 3 terms are roughly equivalent, fast-ATA is ATA-2 but EIDE
additionally includes ATAPI. ATA-2 is what most use these days which
is faster and with DMA. Highest transfer rate is increased to 16.6
MB/s.

3.4.5. Ultra-ATA

A new, faster DMA mode that is approximately twice the speed of EIDE
PIO-Mode 4 (33 MB/s). Disks with and without Ultra-ATA can be mixed on
the same cable without speed penalty for the faster adapters. The
Ultra-ATA interface is electrically identical with the normal Fast-ATA
interface, including the maximum cable length.

The ATA/66 was superceeded by ATA/100 and very recently we have now
gotten ATA/133. While the interface speed has iproved dramatically the
disks are often limited by platter-to-cache limites which today stands
at about 40 MB/s.

For more information read up on these overviews and whitepapers from
Maxtor: Fast Drives Technology
<http://www.maxtor.com/products/FastDrive/default.htm> on the ATA/133
interface and Big Drives Technology
<http://www.maxtor.com/products/BigDrive/default.htm> on breaking the
137 GB limit.

3.4.6. Serial-ATA

A new, standard has been agreed upon, the Serial-ATA interface, backed
by the The Serial ATA <http://www.serial-ata.org/> group who made the
announcement in August 2001.

Advantages are numerous: simple, thin connectors rather than old
cumbersome cable mats that also obstructued air flow, higher speeds
(about 150 MB/s) and backward compatibility.

3.4.7. ATAPI

The ATA Packet Interface was designed to support CD-ROM drives using
the IDE port and like IDE it is cheap and simple.

3.4.8. SCSI

The Small Computer System Interface is a multi purpose interface that
can be used to connect to everything from drives, disk arrays,
printers, scanners and more. The name is a bit of a misnomer as it has
traditionally been used by the higher end of the market as well as in
work stations since it is well suited for multi tasking environments.

The standard interface is 8 bits wide and can address 8 devices.
There is a wide version with 16 bit that is twice as fast on the same
clock and can address 16 devices. The host adapter always counts as a
device and is usually number 7. It is also possible to have 32 bit
wide busses but this usually requires a double set of cables to carry
all the lines.

The old standard was 5 MB/s and the newer fast-SCSI increased this to
10 MB/s. Recently ultra-SCSI, also known as Fast-20, arrived with 20
MB/s transfer rates for an 8 bit wide bus. New low voltage
differential (LVD) signalling allows these high speeds as well as much
longer cabling than before.

Even more recently an even faster standard has been introduced: SCSI
160 (originally named SCSI 160/m) which is capable of a monstrous 160
MB/s over a 16 bit wide bus. Support is scarce yet but for a few 10000
RPM drives that can transfer 40 MB/s sustained. Putting 6 such drives
on a RAID will keep such a bus saturated and also saturate most PCI
busses. Obviously this is only for the very highest end servers per
today. More information on this standard is available at The Ultra 160
SCSI home page <http://www.ultra160-scsi.com/>

Adaptec just announced a Linux driver for their SCSI 160 host adapter.
More information will come when more information becomes available.

Now also SCSI/320 is available.

The higher performance comes at a cost that is usually higher than for
(E)IDE. The importance of correct termination and good quality cables
cannot be overemphasized. SCSI drives also often tend to be of a
higher quality than IDE drives. Also adding SCSI devices tend to be
easier than adding more IDE drives: Often it is only a matter of
plugging or unplugging the device; some people do this without
powering down the system. This feature is most convenient when you
have multiple systems and you can just take the devices from one
system to the other should one of them fail for some reason.

There is a number of useful documents you should read if you use SCSI,
the SCSI HOWTO as well as the SCSI FAQ posted on Usenet News.

SCSI also has the advantage you can connect it easily to tape drives
for backing up your data, as well as some printers and scanners. It is
even possible to use it as a very fast network between computers while
simultaneously share SCSI devices on the same bus. Work is under way
but due to problems with ensuring cache coherency between the
different computers connected, this is a non trivial task.
SCSI numbers are also used for arbitration. If several drives request
service, the drive with the lowest number is given priority.

Note that newer SCSI cards will simultaneously support an array of
different types of SCSI devices all at individually optimized speeds.

3.5. Cabling

I do not intend to make too many comments on hardware but I feel I
should make a little note on cabling. This might seem like a
remarkably low technological piece of equipment, yet sadly it is the
source of many frustrating problems. At todays high speeds one should
think of the cable more of a an RF device with its inherent demands on
impedance matching. If you do not take your precautions you will get a
much reduced reliability or total failure. Some SCSI host adapters are
more sensitive to this than others.

Shielded cables are of course better than unshielded but the price is
much higher. With a little care you can get good performance from a
cheap unshielded cable.

· For Fast-ATA and Ultra-ATA, the maximum cable length is specified
as 45cm (18"). The data lines of both IDE channels are connected on
many boards, though, so they count as one cable. In any case EIDE
cables should be as short as possible. If there are mysterious
crashes or spontaneous changes of data, it is well worth
investigating your cabling. Try a lower PIO mode or disconnect the
second channel and see if the problem still occurs.

· For Cable Select (ATA drives) you set the drive jumpers to cable
select and use the cable to determine master and slave. This is not
much used.

· Do not have a slave on an ATA controller (primary or secondary)
without a master on the same controller, behaviour in these cases
is undetermined.

· Use as short cable as possible, but do not forget the 30 cm minimum
separation for ultra SCSI and 60 cm separation for differential
SCSI.

· Avoid long stubs between the cable and the drive, connect the plug
on the cable directly to the drive without an extension.

· SCSI Cabling limitations:

· Use correct termination for SCSI devices and at the correct
positions: both ends of the SCSI chain. Remember the host adapter
itself may have on board termination.
· Do not mix shielded or unshielded cabling, do not wrap cables
around metal, try to avoid proximity to metal parts along parts of
the cabling. Any such discontinuities can cause impedance
mismatching which in turn can cause reflection of signals which
increases noise on the cable. This problems gets even more severe
in the case of multi channel controllers. Recently someone
suggested wrapping bubble plastic around the cables in order to
avoid too close proximity to metal, a real problem inside crowded
cabinets.

More information on SCSI cabling and termination can be found at
various web pages around the net.

3.6. Host Adapters

This is the other end of the interface from the drive, the part that
is connected to a computer bus. The speed of the computer bus and that
of the drives should be roughly similar, otherwise you have a
bottleneck in your system. Connecting a RAID 0 disk-farm to a ISA card
is pointless. These days most computers come with 32 bit PCI bus
capable of 132 MB/s transfers which should not represent a bottleneck
for most people in the near future.

As the drive electronic migrated to the drives the remaining part that
became the (E)IDE interface is so small it can easily fit into the PCI
chip set. The SCSI host adapter is more complex and often includes a
small CPU of its own and is therefore more expensive and not
integrated into the PCI chip sets available today. Technological
evolution might change this.

Some host adapters come with separate caching and intelligence but as
this is basically second guessing the operating system the gains are
heavily dependent on which operating system is used. Some of the more
primitive ones, that shall remain nameless, experience great gains.
Linux, on the other hand, have so much smarts of its own that the
gains are much smaller.

Mike Neuffer, who did the drivers for the DPT controllers, states that
the DPT controllers are intelligent enough that given enough cache
memory it will give you a big push in performance and suggests that
people who have experienced little gains with smart controllers just
have not used a sufficiently intelligent caching controller.

3.7. Multi Channel Systems

In order to increase throughput it is necessary to identify the most
significant bottlenecks and then eliminate them. In some systems, in
particular where there are a great number of drives connected, it is
advantageous to use several controllers working in parallel, both for
SCSI host adapters as well as IDE controllers which usually have 2
channels built in. Linux supports this.

Some RAID controllers feature 2 or 3 channels and it pays to spread
the disk load across all channels. In other words, if you have two
SCSI drives you want to RAID and a two channel controller, you should
put each drive on separate channels.

3.8. Multi Board Systems

In addition to having both a SCSI and an IDE in the same machine it is
also possible to have more than one SCSI controller. Check the SCSI-
HOWTO on what controllers you can combine. Also you will most likely
have to tell the kernel it should probe for more than just a single
SCSI or a single IDE controller. This is done using kernel parameters
when booting, for instance using LILO. Check the HOWTOs for SCSI and
LILO for how to do this.

Multi board systems can offer significant speed gains if you configure
your disks right, especially for RAID0. Make sure you interleave the
controllers as well as the drives, so that you add drives to the md
RAID device in the right order. If controller 1 is connected to
drives sda and sdc while controller 2 is connected to drives sdb and
sdd you will gain more paralellicity by adding in the order of sda -
sdc - sdb - sdd rather than sda - sdb - sdc - sdd because a read or
write over more than one cluster will be more likely to span two
controllers.

The same methods can also be applied to IDE. Most motherboards come
with typically 4 IDE ports:

· hda primary master

· hdb primary slave

· hdc secondary master

· hdd secondary slave

where the two primaries share one flat cable and the secondaries
share another cable. Modern chipsets keep these independent.
Therefore it is best to RAID in the order hda - hdc - hdb - hdd as
this will most likely parallelise both channels.

3.9. Speed Comparison

The following tables are given just to indicate what speeds are
possible but remember that these are the theoretical maximum speeds.
All transfer rates are in MB per second and bus widths are measured in
bits.

3.9.1. Controllers

IDE : 8.3 - 16.7
Ultra-ATA : 33 - 66

SCSI :
Bus width (bits)

3.9.2. Bus Types

ISA : 8-12
EISA : 33
VESA : 40 (Sometimes tuned to 50)

PCI
Bus width (bits)

Bus Speed (MHz) | 32 64
--------------------------------------------------
33 | 132 264
66 | 264 528
--------------------------------------------------

3.10. Benchmarking

This is a very, very difficult topic and I will only make a few
cautious comments about this minefield. First of all, it is more
difficult to make comparable benchmarks that have any actual meaning.
This, however, does not stop people from trying...

Instead one can use benchmarking to diagnose your own system, to check
it is going as fast as it should, that is, not slowing down. Also you
would expect a significant increase when switching from a simple file
system to RAID, so a lack of performance gain will tell you something
is wrong.

When you try to benchmark you should not hack up your own, instead
look up iozone and bonnie and read the documentation very carefully.
In particular make sure your buffer size is bigger than your RAM size,
otherwise you test your RAM rather than your disks which will give you
unrealistically high performance.

A very simple benchmark can be obtained using hdparm -tT which can be
used both on IDE and SCSI drives.

For more information on benchmarking and software for a number of
platforms, check out ACNC <http://www.acnc.com/benchmarks.html>
benchmark page as well as this one <http://spin.ch/~tpo/bench/> and
also The Benchmarking-HOWTO
<http://www.linuxdoc.org/HOWTO/Benchmarking-HOWTO.html>.

There are also official home pages for bonnie
<http://www.textuality.com/bonnie/>, bonnie++
<http://www.coker.com.au/bonnie++/> and iozone
<http://www.iozone.org>.

Trivia: Bonnie is intended to locate bottlenecks, the name is a
tribute to Bonnie Raitt, "who knows how to use one" as the author puts
it.

3.11. Comparisons

SCSI offers more performance than EIDE but at a price. Termination is
more complex but expansion not too difficult. Having more than 4 (or
in some cases 2) IDE drives can be complicated, with wide SCSI you can
have up to 15 per adapter. Some SCSI host adapters have several
channels thereby multiplying the number of possible drives even
further.

For SCSI you have to dedicate one IRQ per host adapter which can
control up to 15 drives. With EIDE you need one IRQ for each channel
(which can connect up to 2 disks, master and slave) which can cause
conflict.

RLL and MFM is in general too old, slow and unreliable to be of much
use.

3.12. Future Development

SCSI-3 is under way and will hopefully be released soon. Faster
devices are already being announced, recently an 80 MB/s and then a
160 MB/s monster specification has been proposed and also very
recently became commercially available. These are based around the
Ultra-2 standard (which used a 40 MHz clock) combined with a 16 bit
cable.

Some manufacturers already announce SCSI-3 devices but this is
currently rather premature as the standard is not yet firm. As the
transfer speeds increase the saturation point of the PCI bus is
getting closer. Currently the 64 bit version has a limit of 264 MB/s.
The PCI transfer rate will in the future be increased from the current
33 MHz to 66 MHz, thereby increasing the limit to 528 MB/s.

The ATA development is continuing and is increasing the performance
with the new ATA/100 standard. Since most ATA drives are slower in
sustained transfer from platter than this the performance increase
will for most people be small.

More interesting is the Serial ATA development, where the flat cable
will be replaced with a high speed serial link. This makes cabling far
simpler than today and also it solves the problem of cabling
obstructing airflow over the drives.

Another trend is for larger and larger drives. I hear it is possible
to get 75 GB on a single drive though this is rather expensive.
Currently the optimum storage for your money is about 30 GB but also
this is continuously increasing. The introduction of DVD will in the
near future have a big impact, with nearly 20 GB on a single disk you
can have a complete copy of even major FTP sites from around the
world. The only thing we can be reasonably sure about the future is
that even if it won't get any better, it will definitely be bigger.

Addendum: soon after I first wrote this I read that the maximum useful
speed for a CD-ROM was 20x as mechanical stability would be too great
a problem at these speeds. About one month after that again the first
commercial 24x CD-ROMs were available... Currently you can get 40x and
no doubt higher speeds are in the pipeline.

A project to encapsulate SCSI over TCP/IP, called iSCSI
<http://www.ietf.org/internet-drafts/draft-ietf-ips-iscsi-06.txt> has
started, and one Linux iSCSI implementation
<http://www.cs.uml.edu/~mbrown/iSCSI> has appeared.

3.13. Recommendations

My personal view is that EIDE or Ultra ATA is the best way to start
out on your system, especially if you intend to use DOS as well on
your machine. If you plan to expand your system over many years or
use it as a server I would strongly recommend you get SCSI drives.
Currently wide SCSI is a little more expensive. You are generally more
likely to get more for your money with standard width SCSI. There is
also differential versions of the SCSI bus which increases maximum
length of the cable. The price increase is even more substantial and
cannot therefore be recommended for normal users.

In addition to disk drives you can also connect some types of scanners
and printers and even networks to a SCSI bus.

Also keep in mind that as you expand your system you will draw ever
more power, so make sure your power supply is rated for the job and
that you have sufficient cooling. Many SCSI drives offer the option of
sequential spin-up which is a good idea for large systems. See also
``Power and Heating''.

4. File System Structure

Linux has been multi tasking from the very beginning where a number of
programs interact and run continuously. It is therefore important to
keep a file structure that everyone can agree on so that the system
finds data where it expects to. Historically there has been so many
different standards that it was confusing and compatibility was
maintained using symbolic links which confused the issue even further
and the structure ended looking like a maze.

In the case of Linux a standard was fortunately agreed on early on
called the File Systems Standard (FSSTND) which today is used by all
main Linux distributions.

Later it was decided to make a successor that should also support
operating systems other than just Linux, called the Filesystem
Hierarchy Standard (FHS) at version 2.2 currently. This standard is
under continuous development and will soon be adopted by Linux
distributions.

I recommend not trying to roll your own structure as a lot of thought
has gone into the standards and many software packages comply with the
standards. Instead you can read more about this at the FHS home page
<http://www.pathname.com/fhs/>.

This HOWTO endeavours to comply with FSSTND and will follow FHS when
distributions become available.

4.1. File System Features

The various parts of FSSTND have different requirements regarding
speed, reliability and size, for instance losing root is a pain but
can easily be recovered. Losing /var/spool/mail is a rather different
issue. Here is a quick summary of some essential parts and their
properties and requirements. Note that this is just a guide, there can
be binaries in etc and lib directories, libraries in bin directories
and so on.

4.1.1. Swap

Speed
Maximum! Though if you rely too much on swap you should consider
buying some more RAM. Note, however, that on many old Pentium PC
motherboards the cache will not work on RAM above 128 MB.

Size
Similar as for RAM. Quick and dirty algorithm: just as for tea:
16 MB for the machine and 2 MB for each user. Smallest kernel
run in 1 MB but is tight, use 4 MB for general work and light
applications, 8 MB for X11 or GCC or 16 MB to be comfortable.
(The author is known to brew a rather powerful cuppa tea...)

Some suggest that swap space should be 1-2 times the size of the
RAM, pointing out that the locality of the programs determines
how effective your added swap space is. Note that using the same
algorithm as for 4BSD is slightly incorrect as Linux does not
allocate space for pages in core.

A more thorough approach is to consider swap space plus RAM as
your total working set, so if you know how much space you will
need at most, you subtract the physical RAM you have and that is
the swap space you will need.

There is also another reason to be generous when dimensioning
your swap space: memory leaks. Ill behaving programs that do not
free the memory they allocate for themselves are said to have a
memory leak. This allocation remains even after the offending
program has stopped so this is a source of memory consumption.
Only after the program dies is the memory returned. Once all
physical RAM and swap space are exhausted the only solution is
to kill the offending processes if possible, or failing that,
reboot and start over. Thankfully such programs are not too
common but should you come across one you will find that extra
swap space will buy you extra time between reboots.

Also remember to take into account the type of programs you use.
Some programs that have large working sets, such as image
processing software have huge data structures loaded in RAM
rather than working explicitly on disk files. Data and computing
intensive programs like this will cause excessive swapping if
you have less RAM than the requirements.

Other types of programs can lock their pages into RAM. This can
be for security reasons, preventing copies of data reaching a
swap device or for performance reasons such as in a real time
module. Either way, locking pages reduces the remaining amount
of swappable memory and can cause the system to swap earlier
then otherwise expected.

In man 8 mkswap it is explained that each swap partition can be
a maximum of just under 128 MB in size for 32-bit machines and
just under 256 MB for 64-bit machines.

This however changed with kernel 2.2.0 after which the limit is
2 GB. The man page has been updated to reflect this change.

Reliability
Medium. When it fails you know it pretty quickly and failure
will cost you some lost work. You save often, don't you?

Note 1
Linux offers the possibility of interleaved swapping across
multiple devices, a feature that can gain you much. Check out
"man 8 swapon" for more details. However, software raiding swap
across multiple devices adds more overheads than you gain.

Thus the /etc/fstab file might look like this:

/dev/sda1 swap swap pri=1 0 0
/dev/sdc1 swap swap pri=1 0 0

Remember that the fstab file is very sensitive to the formatting
used, read the man page carefully and do not just cut and paste the
lines above.

Note 2
Some people use a RAM disk for swapping or some other file
systems. However, unless you have some very unusual requirements
or setups you are unlikely to gain much from this as this cuts
into the memory available for caching and buffering.

Note 2b
There is once exception: on a number of badly designed
motherboards the on board cache memory is not able to cache all
the RAM that can be addressed. Many older motherboards could
accept 128 MB RAM but only cache the lower 64 MB. In such cases
it would improve the performance if you used the upper
(uncached) 64 MB RAM for RAMdisk based swap or other temporary
storage.

4.1.2. Temporary Storage ( /tmp and /var/tmp )

Speed
Very high. On a separate disk/partition this will reduce
fragmentation generally, though ext2fs handles fragmentation
rather well.

Size
Hard to tell, small systems are easy to run with just a few MB
but these are notorious hiding places for stashing files away
from prying eyes and quota enforcement and can grow without
control on larger machines. Suggested: small home machine: 8 MB,
large home machine: 32 MB, small server: 128 MB, and large
machines up to 500 MB (The machine used by the author at work
has 1100 users and a 300 MB /tmp directory). Keep an eye on
these directories, not only for hidden files but also for old
files. Also be prepared that these partitions might be the first
reason you might have to resize your partitions.

Reliability
Low. Often programs will warn or fail gracefully when these
areas fail or are filled up. Random file errors will of course
be more serious, no matter what file area this is.

Files
Mostly short files but there can be a huge number of them.
Normally programs delete their old tmp files but if somehow an
interruption occurs they could survive. Many distributions have
a policy regarding cleaning out tmp files at boot time, you
might want to check out what your setup is.

Note1
In FSSTND there is a note about putting /tmp on RAM disk. This,
however, is not recommended for the same reasons as stated for
swap. Also, as noted earlier, do not use flash RAM drives for
these directories. One should also keep in mind that some
systems are set to automatically clean tmp areas on rebooting.

Note2
Older systems had a /usr/tmp but this is no longer recommended
and for historical reasons a symbolic link now makes it point to
one of the other tmp areas.

(* That was 50 lines, I am home and dry! *)

4.1.3. Spool Areas ( /var/spool/news and /var/spool/mail )

Speed
High, especially on large news servers. News transfer and
expiring are disk intensive and will benefit from fast drives.
Print spools: low. Consider RAID0 for news.

Size
For news/mail servers: whatever you can afford. For single user
systems a few MB will be sufficient if you read continuously.
Joining a list server and taking a holiday is, on the other
hand, not a good idea. (Again the machine I use at work has 100
MB reserved for the entire /var/spool)

Reliability
Mail: very high, news: medium, print spool: low. If your mail is
very important (isn't it always?) consider RAID for reliability.

Files
Usually a huge number of files that are around a few KB in size.
Files in the print spool can on the other hand be few but quite
sizable.

Note
Some of the news documentation suggests putting all the
.overview files on a drive separate from the news files, check
out all news FAQs for more information. Typical size is about
3-10 percent of total news spool size.

4.1.4. Home Directories ( /home )

Speed
Medium. Although many programs use /tmp for temporary storage,
others such as some news readers frequently update files in the
home directory which can be noticeable on large multiuser
systems. For small systems this is not a critical issue.

Size
Tricky! On some systems people pay for storage so this is
usually then a question of finance. Large systems such as
Nyx.net <http://www.nyx.net/> (which is a free Internet service
with mail, news and WWW services) run successfully with a
suggested limit of 100 KB per user and 300 KB as enforced
maximum. Commercial ISPs offer typically about 5 MB in their
standard subscription packages.

If however you are writing books or are doing design work the
requirements balloon quickly.

Reliability
Variable. Losing /home on a single user machine is annoying but
when 2000 users call you to tell you their home directories are
gone it is more than just annoying. For some their livelihood
relies on what is here. You do regular backups of course?

Files
Equally tricky. The minimum setup for a single user tends to be
a dozen files, 0.5 - 5 KB in size. Project related files can be
huge though.

Note1
You might consider RAID for either speed or reliability. If you
want extremely high speed and reliability you might be looking
at other operating system and hardware platforms anyway. (Fault
tolerance etc.)

Note2
Web browsers often use a local cache to speed up browsing and
this cache can take up a substantial amount of space and cause
much disk activity. There are many ways of avoiding this kind of
performance hits, for more information see the sections on
``Home Directories'' and ``WWW''.

Note3
Users often tend to use up all available space on the /home
partition. The Linux Quota subsystem is capable of limiting the
number of blocks and the number of inode a single user ID can
allocate on a per-filesystem basis. See the Linux Quota mini-
HOWTO <http://www.linuxdoc.org/HOWTO/mini/Quota.html> by Albert
M.C. Tam bertie (at) scn.org for details on setup.

4.1.5. Main Binaries ( /usr/bin and /usr/local/bin )

Speed
Low. Often data is bigger than the programs which are demand
loaded anyway so this is not speed critical. Witness the
successes of live file systems on CD ROM.
Size
The sky is the limit but 200 MB should give you most of what you
want for a comprehensive system. A big system, for software
development or a multi purpose server should perhaps reserve 500
MB both for installation and for growth.

Reliability
Low. This is usually mounted under root where all the essentials
are collected. Nevertheless losing all the binaries is a pain...

Files
Variable but usually of the order of 10 - 100 KB.

4.1.6. Libraries ( /usr/lib and /usr/local/lib )

Speed
Medium. These are large chunks of data loaded often, ranging
from object files to fonts, all susceptible to bloating. Often
these are also loaded in their entirety and speed is of some use
here.

Size
Variable. This is for instance where word processors store their
immense font files. The few that have given me feedback on this
report about 70 MB in their various lib directories. A rather
complete Debian 1.2 installation can take as much as 250 MB
which can be taken as an realistic upper limit. The following
ones are some of the largest disk space consumers: GCC, Emacs,
TeX/LaTeX, X11 and perl.

Reliability
Low. See point ``Main binaries''.

Files
Usually large with many of the order of 1 MB in size.

Note
For historical reasons some programs keep executables in the lib
areas. One example is GCC which have some huge binaries in the
/usr/lib/gcc/lib hierarchy.

4.1.7. Boot

Speed
Quite low: after all booting doesn't happen that often and
loading the kernel is just a tiny fraction of the time it takes
to get the system up and running.

Size
Quite small, a complete image with some extras fit on a single
floppy so 5 MB should be plenty.

Reliability
High. See section below on Root.

Note 1
The most important part about the Boot partition is that on many
systems it must reside below cylinder 1023. This is a BIOS
limitation that Linux cannot get around.

Note 1a
The above is not necessarily true for recent IDE systems and not
for any SCSI disks. For more information check the latest Large
Disk HOWTO.

Note 2
Recently a new boot loader has been written that overcomes the
1023 sector limit. For more information check out this article
<http://www.linuxforum.com/plug/articles/nuni.html> on nuni.

4.1.8. Root

Speed
Quite low: only the bare minimum is here, much of which is only
run at startup time.

Size
Relatively small. However it is a good idea to keep some
essential rescue files and utilities on the root partition and
some keep several kernel versions. Feedback suggests about 20 MB
would be sufficient.

Reliability
High. A failure here will possibly cause a fair bit of grief and
you might end up spending some time rescuing your boot
partition. With some practice you can of course do this in an
hour or so, but I would think if you have some practice doing
this you are also doing something wrong.

Naturally you do have a rescue disk? Of course this is updated
since you did your initial installation? There are many ready
made rescue disks as well as rescue disk creation tools you
might find valuable. Presumably investing some time in this
saves you from becoming a root rescue expert.

Note 1
If you have plenty of drives you might consider putting a spare
emergency boot partition on a separate physical drive. It will
cost you a little bit of space but if your setup is huge the
time saved, should something fail, will be well worth the extra
space.

Note 2
For simplicity and also in case of emergencies it is not
advisable to put the root partition on a RAID level 0 system.
Also if you use RAID for your boot partition you have to
remember to have the md option turned on for your emergency
kernel.

Note 3
For simplicity it is quite common to keep Boot and Root on the
same partition. If you do that, then in order to boot from LILO
it is important that the essential boot files reside wholly
within cylinder 1023. This includes the kernel as well as files
found in /boot.

4.1.9. DOS etc.

At the danger of sounding heretical I have included this little
section about something many reading this document have strong
feelings about. Unfortunately many hardware items come with setup and
maintenance tools based around those systems, so here goes.

Speed
Very low. The systems in question are not famed for speed so
there is little point in using prime quality drives.
Multitasking or multi-threading are not available so the command
queueing facility found in SCSI drives will not be taken
advantage of. If you have an old IDE drive it should be good
enough. The exception is to some degree Win95 and more notably
NT which have multi-threading support which should theoretically
be able to take advantage of the more advanced features offered
by SCSI devices.

Size
The company behind these operating systems is not famed for
writing tight code so you have to be prepared to spend a few
tens of MB depending on what version you install of the OS or
Windows. With an old version of DOS or Windows you might fit it
all in on 50 MB.

Reliability
Ha-ha. As the chain is no stronger than the weakest link you can
use any old drive. Since the OS is more likely to scramble
itself than the drive is likely to self destruct you will soon
learn the importance of keeping backups here.

Put another way: "Your mission, should you choose to accept it,
is to keep this partition working. The warranty will self
destruct in 10 seconds..."

Recently I was asked to justify my claims here. First of all I
am not calling DOS and Windows sorry excuses for operating
systems. Secondly there are various legal issues to be taken
into account. Saying there is a connection between the last two
sentences are merely the ravings of the paranoid. Surely.
Instead I shall offer the esteemed reader a few key words: DOS
4.0, DOS 6.x and various drive compression tools that shall
remain nameless.

4.2. Explanation of Terms

Naturally the faster the better but often the happy installer of Linux
has several disks of varying speed and reliability so even though this
document describes performance as 'fast' and 'slow' it is just a rough
guide since no finer granularity is feasible. Even so there are a few
details that should be kept in mind:

4.2.1. Speed

This is really a rather woolly mix of several terms: CPU load,
transfer setup overhead, disk seek time and transfer rate. It is in
the very nature of tuning that there is no fixed optimum, and in most
cases price is the dictating factor. CPU load is only significant for
IDE systems where the CPU does the transfer itself but is generally
low for SCSI, see SCSI documentation for actual numbers. Disk seek
time is also small, usually in the millisecond range. This however is
not a problem if you use command queueing on SCSI where you then
overlap commands keeping the bus busy all the time. News spools are a
special case consisting of a huge number of normally small files so in
this case seek time can become more significant.

There are two main parameters that are of interest here:

Seek
is usually specified in the average time take for the read/write
head to seek from one track to another. This parameter is
important when dealing with a large number of small files such
as found in spool files. There is also the extra seek delay
before the desired sector rotates into position under the head.
This delay is dependent on the angular velocity of the drive
which is why this parameter quite often is quoted for a drive.
Common values are 4500, 5400 and 7200 RPM (rotations per
minute). Higher RPM reduces the seek time but at a substantial
cost. Also drives working at 7200 RPM have been known to be
noisy and to generate a lot of heat, a factor that should be
kept in mind if you are building a large array or "disk farm".
Very recently drives working at 10000 RPM has entered the market
and here the cooling requirements are even stricter and minimum
figures for air flow are given.

Transfer
is usually specified in megabytes per second. This parameter is
important when handling large files that have to be transferred.
Library files, dictionaries and image files are examples of
this. Drives featuring a high rotation speed also normally have
fast transfers as transfer speed is proportional to angular
velocity for the same sector density.

It is therefore important to read the specifications for the drives
very carefully, and note that the maximum transfer speed quite often
is quoted for transfers out of the on board cache (burst speed) and
not directly from the platter (sustained speed). See also section on
``Power and Heating''.

4.2.2. Reliability

Naturally no-one would want low reliability disks but one might be
better off regarding old disks as unreliable. Also for RAID purposes
(See the relevant information) it is suggested to use a mixed set of
disks so that simultaneous disk crashes become less likely.

So far I have had only one report of total file system failure but
here unstable hardware seemed to be the cause of the problems.

Disks are cheap these days yet people still underestimate the value of
the contents of the drives. If you need higher reliability make sure
you replace old drives and keep spares. It is not unusual that drives
can work more or less continuous for years and years but what often
kills a drive in the end is power cycling.

4.2.3. Files

The average file size is important in order to decide the most
suitable drive parameters. A large number of small files makes the
average seek time important whereas for big files the transfer speed
is more important. The command queueing in SCSI devices is very handy
for handling large numbers of small files, but for transfer EIDE is
not too far behind SCSI and normally much cheaper than SCSI.

5. File Systems

Over time the requirements for file systems have increased and the
demands for large structures, large files, long file names and more
has prompted ever more advanced file systems, the system that accesses
and organises the data on mass storage. Today there is a large number
of file systems to choose from and this section will describe these in
detail.

The emphasis is on Linux but with more input I will be happy to add
information for a wider audience.

5.1. General Purpose File Systems

Most operating systems usually have a general purpose file system for
every day use for most kinds of files, reflecting available features
in the OS such as permission flags, protection and recovery.

5.1.1. minix

This was the original fs for Linux, back in the days Linux was hosted
on minix machines. It is simple but limited in features and hardly
ever used these days other than in some rescue disks as it is rather
compact.

5.1.2. xiafs and extfs

These are also old and have fallen in disuse and are no longer
recommended.

5.1.3. ext2fs

This is the established standard for general purpose in the Linux
world. It is fast, efficient and mature and is under continuous
development and features such as ACL and transparent compression are
on the horizon.

For more information check the ext2fs
<http://web.mit.edu/tytso/www/linux/ext2.html> home page.

5.1.4. ext3fs

This is the name for the upcoming successor to ext2fs due to enter
stable kernel in the near future. Many features are added to ext2fs
but to avoid confusion over the name after such a radical upgrade the
name will be changed too. You may have heard of it already but source
code is now in beta release .

Patches are available at Linux.org
<ftp://ftp.linux.org.uk/pub/linux/sct/fs/jfs>.

5.1.5. ufs

This is the fs used by BSD and variants thereof. It is mature but also
developed for older types of disk drives where geometries were known.
The fs uses a number of tricks to optimise performance but as disk
geometries are translated in a number of ways the net effect is no
longer so optimal.

5.1.6. efs

The Extent File System (efs) is Silicon Graphics' early file system
widely used on IRIX before version 6.0 after which xfs has taken over.
While migration to xfs is encouraged efs is still supported and much
used on CDs.

There is a Linux driver available in early beta stage, available at
Linux extent file system <http://aeschi.ch.eu.org/efs/> home page.

5.1.7. XFS

Silicon Graphics Inc (sgi) <http://www.sgi.com/> has started porting
its mainframe grade file system to Linux. Source is not yet available
as they are busily cleaning out legal encumbrance but once that is
done they will provide the source code under GPL.

More information is already available on the XFS project page
<http://oss.sgi.com/projects/xfs/> at SGI.

5.1.8. reiserfs

As of July, 23th 1997 Hans Reiser reiser (at) RICOCHET.NET has put up
the source to his tree based reiserfs <http://www.namesys.com> on the
web. While his filesystem has some very interesting features and is
much faster than ext2fs and is in use by a number of people.
Hopefully it will be ready for kernel 2.4.0 which might be ready at
the end of the year.

5.1.9. enh-fs

The Enhanced File System project is now dead.

5.1.10. Tux2 fs

This is a variation on the ext2fs that adds robustness in case of
unexpected interruptions such as power failure. After such an event
Tux2 fs will restart with the file system in a consistent, recently
recorded state without fsck or other recovery operations. To achieve
this Tux2 fs uses a newly designed algorithm called Phase Tree.

More information can be found at the project home page
<http://tux2.sourceforge.net>.

5.2. Microsoft File Systems

This company is responsible for a lot, including a number of
filesystems that has at the very least caused confusions.

5.2.1. fat

Actually there are 2 fats out there, fat12 and fat16 depending on the
partition size used but fortunately the difference is so minor that
the whole issue is transparent.

On the plus side these are fast and simple and most OSes understands
it and can both read and write this fs. And that is about it.

The minus side is limited safety, severely limited permission flags
and atrocious scalability. For instance with fat you cannot have
partitions larger than 2 GB.

5.2.2. fat32

After about 10 years Microsoft realised fat was about, well, 10 years
behind the times and created this fs which scales reasonably well.

Permission flags are still limited. NT 4.0 cannot read this file
system but Linux can.

5.2.3. vfat

At the same time as Microsoft launched fat32 they also added support
for long file names, known as vfat.

Linux reads vfat and fat32 partitions by mounting with type vfat.

5.2.4. ntfs

This is the native fs of Win-NT but as complete information is not
available there is limited support for other OSes.

5.3. Logging and Journaling File Systems

These take a radically different approach to file updates by logging
modifications for files in a log and later at some time checkpointing
the logs.

Reading is roughly as fast as traditional file systems that always
update the files directly. Writing is much faster as only updates are
appended to a log. All this is transparent to the user. It is in
reliability and particularly in checking file system integrity that
these file systems really shine. Since the data before last
checkpointing is known to be good only the log has to be checked, and
this is much faster than for traditional file systems.

Note that while logging filesystems keep track of changes made to both
data and inodes, journaling filesystems keep track only of inode
changes.

Linux has quite a choice in such file systems but none are yet in
production quality. Some are also on hold.

· Adam Richter from Yggdrasil posted some time ago that they have
been working on a compressed log file based system but that this
project is currently on hold. Nevertheless a non-working version is
available on their FTP server. Check out the Yggdrasil ftp server
<ftp://ftp.yggdrasil.com/private/adam> where special patched
versions of the kernel can be found.

· Another project is the Linux log-structured Filesystem Project
<http://outflux.net/projects/lfs/> which sadly also is on hold.
Nevertheless this page contains much information on the topic.

· Then there is the LinLogFS -- A Log-Structured Filesystem For Linux
<http://www.complang.tuwien.ac.at/czezatke/lfs.html> (formerly
known as dtfs) which seems to be going strong. Still in alpha but
sufficiently complete to make programs run off this file system

· Finally there is the Journaling Flash File System
<http://developer.axis.com/software/jffs/> designed for their
embedded diskless systems such as their Linux based web camera.

Note that ext3fs, XFS and reiserfs also have features for logging or
journaling.

5.4. Read-only File Systems

Read-only media has not escaped the ever increasing complexities seen
in more general file systems so again there is a large choice to
choose from with corresponding opportunities for exciting mistakes.

Note that ext2fs works quite well on a CD-ROM and seems to save space
while offering the normal file system features such as long file names
and permissions that can be retained when copying files across to
read-write media. Also having /dev on a CD-ROM is possible.

Most of these are used with the CD-ROM media but also the new DVD can
be used and you can even use it through the loopback device on a hard
disk file for verifying an image before burning a ROM.

There is a read-only romfs for Linux but as that is not disk related
nothing more will be said about it here.

5.4.1. High Sierra

This was one of the earliest standards for CD-ROM formats, supposedly
named after the hotel where the final agreement took place.

High Sierra was so limited in features that new extensions simply had
to appear and while there has been no end to new formats the original
High Sierra remains the common precursor and is therefore still widely
supported.

5.4.2. iso9660

The International Standards Organisation made their extensions and
formalised the standard into what we know as the iso9660 standard.

The Linux iso9660 file system supports both High Sierra as well as
Rock Ridge extensions.

5.4.3. Rock Ridge

Not everyone accepts limits like short filenames and lack of
permissions so very soon the Rock Ridge extensions appeared to rectify
these shortcomings.

5.4.4. Joliet

Microsoft, not be be outdone in the standards extension game, decided
it should extend CD-ROM formats with some internationalisation
features and called it Joliet.

Linux supports this standards in kernels 2.0.34 or newer. You need to
enable NLS in order to use it.

5.4.5. Trivia

Joliet is a city outside Chicago; best known for being the site of the
prison where Jake was locked up in the movie "Blues Brothers." Rock
Ridge (the UNIX extensions to ISO 9660) is named after the (fictional)
town in the movie "Blazing Saddles."

5.4.6. UDF

With the arrival of DVD with up to about 17 GB of storage capacity the
world seemingly needed another format, this time ambitiously named
Universal Disk Format (UDF). This is intended to replace iso9660 and
will be required for DVD.

Currently this is not in the standard Linux kernel but a project is
underway to make a <http://trylinux.com/projects/udf/index.html>
name="UDF driver"> for Linux. Patches and documentation are available.

More information is also available at the Linux and DVDs
<http://atv.ne.mediaone.net/linux-dvd/> page.

5.5. Networking File Systems

There is a large number of networking technologies available that lets
you distribute disks throughout a local or even global networks. This
is somewhat peripheral to the topic of this HOWTO but as it can be
used with local disks I will cover this briefly. It would be best if
someone (else) took this into a separate HOWTO...

5.5.1. NFS

This is one of the earliest systems that allows mounting a file space
on one machine onto another. There are a number of problems with NFS
ranging from performance to security but it has nevertheless become
established.

5.5.2. AFS

This is a system that allows efficient sharing of files across large
networks. Starting out as an academic project it is now sold by
Transarc <http://www.transarc.com> whose home page gives you more
details.

Derek Atkins, of MIT, ported AFS to Linux and has also set up the
Linux AFS mailing List ( linux-afs@mit.edu) for this which is open to
the public. Requests to join the list should go to linux-afs-
request@mit.edu and finally bug reports should be directed to linux-
afs-bugs@mit.edu.

Important: as AFS uses encryption it is restricted software and cannot
easily be exported from the US.

IBM who owns Transarc, has announced the availability of the latest
version of client as well as server for Linux.

Arla is a free AFS implementation, check the Arla homepage
<http://www.stacken.kth.se/projekt/arla/> for more information as well
as documentation.

5.5.3. Coda

A networking filesystem similar to AFS is underway and is called Coda
<http://coda.cs.cmu.edu/>. This is designed to be more robust and
fault tolerant than AFS, and supports mobile, disconnected operations.
Currently it does not scale very well, and does not really have proper
administrative tools, as AFS does and ARLA is beginning to.

5.5.4. nbd

The Network Block Device <http://atrey.karlin.mff.cuni.cz/~pavel/>
(nbd) is available in Linux kernel 2.2 and later and offers reportedly
excellent performance. The interesting thing here is that it can be
combined with RAID (see later).

5.5.5. enbd

The <http://www.it.uc3m.es/~ptb/nbd> name="Enhanced Network Block
Device"> (enbd) is a project to enhance the nbd with features such as
block journaled multi channel communications, internal failover and
automatic balancing between channels and more.

The intended use is for RAID over the net.

5.5.6. GFS

The Global File System <http://gfs.lcse.umn.edu/> is a new file system
designed for storage across a wide area network. It is currently in
the early stages and more information will come later.

5.6. Special File Systems

In addition to the general file systems there is also a number of more
specific ones, usually to provide higher performance or other
features, usually with a tradeoff in other respects.

5.6.1. tmpfs and swapfs

For short term fast file storage SunOS offers tmpfs which is about the
same as the swapfs on NeXT. This overcomes the inherent slowness in
ufs by caching file data and keeping control information in memory.
This means that data on such a file system will be lost when rebooting
and is therefore mainly suitable for /tmp area but not /var/tmp which
is where temporary data that must survive a reboot, is placed.

SunOS offers very limited tuning for tmpfs and the number of files is
even limited by total physical memory of the machine.

Linux now features tmpfs since kernel version 2.4 and is enabled by
turning on virtual memory file system support (former shm fs). Under
certain circumstances tmpfs can lock up the system in early kerbel
versions, make sure you use version 2.4.6 or later.

5.6.2. userfs

The user file system (userfs) allows a number of extensions to
traditional file system use such as FTP based file system, compression
(arcfs) and fast prototyping and many other features. The docfs is
based on this filesystem. Check the userfs homepage
<http://www.goop.org/~jeremy/userfs/> for more information.

5.6.3. devfs

When disks are added, removed or just fail it is likely that disk
device names of the remaining disks will change. For instance if sdb
fails then the old sdc becomes sdb, the old sdc becomes sdb and so on.
Note that in this case hda, hdb etc will remain unchanged. Likewise
if a new drive is added the reverse may happen.

There is no guarantee that SCSI ID 0 becomes sda and that adding disks
in increasing ID order will just add a new device name without
renaming previous entries, as some SCSI drivers assign from ID 0 and
up while others reverse the scanning order. Likewise adding a SCSI
host adapter can also cause renaming.

Generally device names are assigned in the order they are found.

The source of the problem lies in the limited number of bits available
for major and minor numbering in the device files used to describe the
device itself. You an see these in the /dev directory, info on the
numbering and allocation can be found in man MAKEDEV. Currently there
are 2 solutions to this problem in various stages of development:

scsidev
works by creating a database of drives and where they belong,
check man scsifs and the scsidev home page for more information

devfs
is a more long term project aimed at getting around the whole
business of device numbering by making the /dev directory a
kernel file system in the same way as /proc is. More
information will appear as it becomes available.

5.6.4. smugfs

For a number of reasons it is currently difficult to have files bigger
than 2 GB. One file system that tries to overcome this limit is smugfs
which is very fast but also simple. For instance there are no
directories and the block allocation is simple.

It is available as compressed tarred source code
<ftp://atrey.karlin.mff.cuni.cz/pub/local/mj/linux/> and while it
worked with kernel version 2.1.85 it is quite possible some work is
required to make it fit into newer kernels. Also the low version
number (0.0) suggests extra care is required.

5.7. File System Recommendations

There is a jungle of choices but generally it is recommended to use
the general file system that comes with your distribution. If you use
ufs and have some kind of tmpfs available you should first start off
with the general file system to get an idea of the space requirements
and if necessary buy more RAM to support the size of tmpfs you need.
Otherwise you will end up with mysterious crashes and lost time.

If you use dual boot and need to transfer data between the two OSes
one of the simplest ways is to use an appropriately sized partition
formatted with fat as most systems can reliably read and write this.
Remember the limit of 2 GB for fat partitions.

For more information of file system interconnectivity you can check
out the file system
<http://students.ceid.upatras.gr/~gef/fs/oldindex.html> page which has
been superseded by file system <http://www.penguin.cz/~mhi/fs/> and
the article Kragen's Amazing List of Filesystems
<http://linuxtoday.com/stories/5556.html>.

That guide is being superseded by a HOWTO which is underway and a link
will be added when it is ready.

To avoid total havoc with device renaming if a drive fails check out
the scanning order of your system and try to keep your root system on
hda or sda and removable media such as ZIP drives at the end of the
scanning order.

6. Technologies

In order to decide how to get the most of your devices you need to
know what technologies are available and their implications. As always
there can be some tradeoffs with respect to speed, reliability, power,
flexibility, ease of use and complexity.

Many of the techniques described below can be stacked in a number of
ways to maximise performance and reliability, though at the cost of
added complexity.

6.1. RAID

This is a method of increasing reliability, speed or both by using
multiple disks in parallel thereby decreasing access time and
increasing transfer speed. A checksum or mirroring system can be used
to increase reliability. Large servers can take advantage of such a
setup but it might be overkill for a single user system unless you
already have a large number of disks available. See other documents
and FAQs for more information.

For Linux one can set up a RAID system using either software (the md
module in the kernel), a Linux compatible controller card (PCI-to-
SCSI) or a SCSI-to-SCSI controller. Check the documentation for what
controllers can be used. A hardware solution is usually faster, and
perhaps also safer, but comes at a significant cost.

A summary of available hardware RAID solutions for Linux is available
at Linux Consulting <http://www.Linux-
Consulting.com/Raid/Docs/raid_hw.txt>.

6.1.1. SCSI-to-SCSI

SCSI-to-SCSI controllers are usually implemented as complete cabinets
with drives and a controller that connects to the computer with a
second SCSI bus. This makes the entire cabinet of drives look like a
single large, fast SCSI drive and requires no special RAID driver. The
disadvantage is that the SCSI bus connecting the cabinet to the
computer becomes a bottleneck.

A significant disadvantage for people with large disk farms is that
there is a limit to how many SCSI entries there can be in the /dev
directory. In these cases using SCSI-to-SCSI will conserve entries.

Usually they are configured via the front panel or with a terminal
connected to their on-board serial interface.

Some manufacturers of such systems are CMD <http://www.cmd.com> and
Syred <http://www.syred.com> whose web pages describe several systems.

6.1.2. PCI-to-SCSI

PCI-to-SCSI controllers are, as the name suggests, connected to the
high speed PCI bus and is therefore not suffering from the same
bottleneck as the SCSI-to-SCSI controllers. These controllers require
special drivers but you also get the means of controlling the RAID
configuration over the network which simplifies management.

Currently only a few families of PCI-to-SCSI host adapters are
supported under Linux.

DPT
The oldest and most mature is a range of controllers from DPT
<http://www.dpt.com> including SmartCache I/III/IV and SmartRAID
I/III/IV controller families. These controllers are supported
by the EATA-DMA driver in the standard kernel. This company also
has an informative home page <http://www.dpt.com> which also
describes various general aspects of RAID and SCSI in addition
to the product related information.

More information from the author of the DPT controller drivers
(EATA* drivers) can be found at his pages on SCSI
<http://www.uni-mainz.de/~neuffer/scsi/> and DPT
<http://www.uni-mainz.de/~neuffer/scsi/dpt/>.

These are not the fastest but have a good track record of proven
reliability.

Note that the maintenance tools for DPT controllers currently
run under DOS/Win only so you will need a small DOS/Win
partition for some of the software. This also means you have to
boot the system into Windows in order to maintain your RAID
system.

ICP-Vortex
A very recent addition is a range of controllers from ICP-Vortex
<http://www.icp-vortex.com> featuring up to 5 independent
channels and very fast hardware based on the i960 chip. The
Linux driver was written by the company itself which shows they
support Linux.

As ICP-Vortex supplies the maintenance software for Linux it is
not necessary with a reboot to other operating systems for the
setup and maintenance of your RAID system. This saves you also
extra downtime.

Mylex DAC-960
This is one of the latest entries which is out in early beta.
More information as well as drivers are available at Dandelion
Digital's Linux DAC960 Page
<http://www.dandelion.com/Linux/DAC960.html>.

Compaq Smart-2 PCI Disk Array Controllers
Another very recent entry and currently in beta release is the
Smart-2 <http://www.insync.net/~frantzc/cpqarray.html> driver.

IBM ServeRAID
IBM has released their driver
<http://www.developer.ibm.com/welcome/netfinity/serveraid_beta.html>
as GPL.

6.1.3. Software RAID

A number of operating systems offer software RAID using ordinary disks
and controllers. Cost is low and performance for raw disk IO can be
very high. As this can be very CPU intensive it increases the load
noticeably so if the machine is CPU bound in performance rather then
IO bound you might be better off with a hardware PCI-to-RAID
controller.

Real cost, performance and especially reliability of software vs.
hardware RAID is a very controversial topic. Reliability on Linux
systems have been very good so far.

The current software RAID project on Linux is the md system (multiple
devices) which offers much more than RAID so it is described in more
details later.

6.1.4. RAID Levels

RAID comes in many levels and flavours which I will give a brief
overview of this here. Much has been written about it and the
interested reader is recommended to read more about this in the
Software RAID HOWTO <http://ostenfeld.dk/~jakob/Software-RAID.HOWTO/>.

· RAID 0 is not redundant at all but offers the best throughput of
all levels here. Data is striped across a number of drives so read
and write operations take place in parallel across all drives. On
the other hand if a single drive fail then everything is lost. Did
I mention backups?

· RAID 1 is the most primitive method of obtaining redundancy by
duplicating data across all drives. Naturally this is massively
wasteful but you get one substantial advantage which is fast
access. The drive that access the data first wins. Transfers are
not any faster than for a single drive, even though you might get
some faster read transfers by using one track reading per drive.

Also if you have only 2 drives this is the only method of achieving
redundancy.

· RAID 2 and 4 are not so common and are not covered here.

· RAID 3 uses a number of disks (at least 2) to store data in a
striped RAID 0 fashion. It also uses an additional redundancy disk
to store the XOR sum of the data from the data disks. Should the
redundancy disk fail, the system can continue to operate as if
nothing happened. Should any single data disk fail the system can
compute the data on this disk from the information on the
redundancy disk and all remaining disks. Any double fault will
bring the whole RAID set off-line.

RAID 3 makes sense only with at least 2 data disks (3 disks
including the redundancy disk). Theoretically there is no limit for
the number of disks in the set, but the probability of a fault
increases with the number of disks in the RAID set. Usually the
upper limit is 5 to 7 disks in a single RAID set.

Since RAID 3 stores all redundancy information on a dedicated disk
and since this information has to be updated whenever a write to
any data disk occurs, the overall write speed of a RAID 3 set is
limited by the write speed of the redundancy disk. This, too, is a
limit for the number of disks in a RAID set. The overall read speed
of a RAID 3 set with all data disks up and running is that of a
RAID 0 set with that number of data disks. If the set has to
reconstruct data stored on a failed disk from redundant
information, the performance will be severely limited: All disks in
the set have to be read and XOR-ed to compute the missing
information.

· RAID 5 is just like RAID 3, but the redundancy information is
spread on all disks of the RAID set. This improves write
performance, because load is distributed more evenly between all
available disks.

There are also hybrids available based on RAID 0 or 1 and one other
level. Many combinations are possible but I have only seen a few
referred to. These are more complex than the above mentioned RAID
levels.

RAID 0/1 combines striping with duplication which gives very high
transfers combined with fast seeks as well as redundancy. The
disadvantage is high disk consumption as well as the above mentioned
complexity.

RAID 1/5 combines the speed and redundancy benefits of RAID5 with the
fast seek of RAID1. Redundancy is improved compared to RAID 0/1 but
disk consumption is still substantial. Implementing such a system
would involve typically more than 6 drives, perhaps even several
controllers or SCSI channels.

6.2. Volume Management

Volume management is a way of overcoming the constraints of fixed
sized partitions and disks while still having a control of where
various parts of file space resides. With such a system you can add
new disks to your system and add space from this drive to parts of the
file space where needed, as well as migrating data out from a disk
developing faults to other drives before catastrophic failure occurs.

The system developed by Veritas <http://www.veritas.com> has become
the defacto standard for logical volume management.

Volume management is for the time being an area where Linux is
lacking.

One is the virtual partition system project VPS <http://www-
wsg.cso.uiuc.edu/~roth/> that will reimplement many of the volume
management functions found in IBM's AIX system. Unfortunately this
project is currently on hold.

Another project is the Logical Volume Manager
<http://www.sistina.com/lvm/> project that is similar to a project by
HP.

6.3. Linux md Kernel Patch

The Linux Multi Disk (md) provides a number of block level features in
various stages of development.

RAID 0 (striping) and concatenation are very solid and in production
quality and also RAID 4 and 5 are quite mature.

It is also possible to stack some levels, for instance mirroring (RAID
1) two pairs of drives, each pair set up as striped disks (RAID 0),
which offers the speed of RAID 0 combined with the reliability of RAID
1.

In addition to RAID this system offers (in alpha stage) block level
volume management and soon also translucent file space. Since this is
done on the block level it can be used in combination with any file
system, even for fat using Wine.

Think very carefully what drives you combine so you can operate all
drives in parallel, which gives you better performance and less wear.
Read more about this in the documentation that comes with md.

Unfortunately The Linux software RAID has split into two trees, the
old stable versions 0.35 and 0.42 which are documented in the official
Software-RAID HOWTO <http://linas.org/linux/Software-RAID/Software-
RAID.html> and the newer less stable 0.90 series which is documented
in the unofficial Software RAID HOWTO
<http://ostenfeld.dk/~jakob/Software-RAID.HOWTO/> which is a work in
progress.

A patch for online growth of ext2fs <http://www-
mddsp.enel.ucalgary.ca/People/adilger/online-ext2/> is available in
early stages and related work is taking place at the ext2fs resize
project <http://ext2resize.sourceforge.net/> at Sourceforge.

Hint: if you cannot get it to work properly you have forgotten to set
the persistent-block flag. Your best documentation is currently the
source code.

6.4. Compression

Disk compression versus file compression is a hotly debated topic
especially regarding the added danger of file corruption. Nevertheless
there are several options available for the adventurous
administrators. These take on many forms, from kernel modules and
patches to extra libraries but note that most suffer various forms of
limitations such as being read-only. As development takes place at
neck breaking speed the specs have undoubtedly changed by the time you
read this. As always: check the latest updates yourself. Here only a
few references are given.

· DouBle features file compression with some limitations.

· Zlibc adds transparent on-the-fly decompression of files as they
load.

· there are many modules available for reading compressed files or
partitions that are native to various other operating systems
though currently most of these are read-only.

· dmsdos <http://bf9nt.uni-
duisburg.de/mitarbeiter/gockel/software/dmsdos/> (currently in
version 0.9.2.0) offer many of the compression options available
for DOS and Windows. It is not yet complete but work is ongoing and
new features added regularly.

· e2compr is a package that extends ext2fs with compression
capabilities. It is still under testing and will therefore mainly
be of interest for kernel hackers but should soon gain stability
for wider use. Check the <http://e2compr.memalpha.cx/e2compr/>
name="e2compr homepage"> for more information. I have reports of
speed and good stability which is why it is mentioned here.

6.5. ACL

Access Control List (ACL) offers finer control over file access on a
user by user basis, rather than the traditional owner, group and
others, as seen in directory listings (drwxr-xr-x). This is currently
not available in Linux but is expected in kernel 2.3 as hooks are
already in place in ext2fs.

6.6. cachefs

This uses part of a hard disk to cache slower media such as CD-ROM.
It is available under SunOS but not yet for Linux.

6.7. Translucent or Inheriting File Systems

This is a copy-on-write system where writes go to a different system
than the original source while making it look like an ordinary file
space. Thus the file space inherits the original data and the
translucent write back buffer can be private to each user.

There is a number of applications:

· updating a live file system on CD-ROM, making it flexible, fast
while also conserving space,

· original skeleton files for each new user, saving space since the
original data is kept in a single space and shared out,

· parallel project development prototyping where every user can
seemingly modify the system globally while not affecting other
users.

SunOS offers this feature and this is under development for Linux.
There was an old project called the Inheriting File Systems (ifs) but
this project has stopped. One current project is part of the md
system and offers block level translucence so it can be applied to any
file system.

Sun has an informative page <http://www.sun.ca/white-papers/tfs.html>
on translucent file system.

It should be noted that Clearcase (now owned by Rational)
<http://www.rational.com> pioneered and popularized translucent
filesystems for software configuration management by writing their own
UNIX filesystem.

6.8. Physical Track Positioning

This trick used to be very important when drives were slow and small,
and some file systems used to take the varying characteristics into
account when placing files. Although higher overall speed, on board
drive and controller caches and intelligence has reduced the effect of
this.

Nevertheless there is still a little to be gained even today. As we
know, "world dominance" is soon within reach but to achieve this
"fast" we need to employ all the tricks we can use .

To understand the strategy we need to recall this near ancient piece
of knowledge and the properties of the various track locations. This
is based on the fact that transfer speeds generally increase for
tracks further away from the spindle, as well as the fact that it is
faster to seek to or from the central tracks than to or from the inner
or outer tracks.

Most drives use disks running at constant angular velocity but use
(fairly) constant data density across all tracks. This means that you
will get much higher transfer rates on the outer tracks than on the
inner tracks; a characteristics which fits the requirements for large
libraries well.

Newer disks use a logical geometry mapping which differs from the
actual physical mapping which is transparently mapped by the drive
itself. This makes the estimation of the "middle" tracks a little
harder.

In most cases track 0 is at the outermost track and this is the
general assumption most people use. Still, it should be kept in mind
that there are no guarantees this is so.

Inner
tracks are usually slow in transfer, and lying at one end of the
seeking position it is also slow to seek to.

This is more suitable to the low end directories such as DOS,
root and print spools.

Middle
tracks are on average faster with respect to transfers than
inner tracks and being in the middle also on average faster to
seek to.

This characteristics is ideal for the most demanding parts such
as swap, /tmp and /var/tmp.

Outer
tracks have on average even faster transfer characteristics but
like the inner tracks are at the end of the seek so
statistically it is equally slow to seek to as the inner tracks.

Large files such as libraries would benefit from a place here.

Hence seek time reduction can be achieved by positioning frequently
accessed tracks in the middle so that the average seek distance and
therefore the seek time is short. This can be done either by using
fdisk or cfdisk to make a partition on the middle tracks or by first
making a file (using dd) equal to half the size of the entire disk
before creating the files that are frequently accessed, after which
the dummy file can be deleted. Both cases assume starting from an
empty disk.

The latter trick is suitable for news spools where the empty directory
structure can be placed in the middle before putting in the data
files. This also helps reducing fragmentation a little.

This little trick can be used both on ordinary drives as well as RAID
systems. In the latter case the calculation for centring the tracks
will be different, if possible. Consult the latest RAID manual.

The speed difference this makes depends on the drives, but a 50
percent improvement is a typical value.

6.8.1. Disk Speed Values

The same mechanical head disk assembly (HDA) is often available with a
number of interfaces (IDE, SCSI etc) and the mechanical parameters are
therefore often comparable. The mechanics is today often the limiting
factor but development is improving things steadily. There are two
main parameters, usually quoted in milliseconds (ms):

· Head movement - the speed at which the read-write head is able to
move from one track to the next, called access time. If you do the
mathematics and doubly integrate the seek first across all possible
starting tracks and then across all possible target tracks you will
find that this is equivalent of a stroke across a third of all
tracks.

· Rotational speed - which determines the time taken to get to the
right sector, called latency.

After voice coils replaced stepper motors for the head movement the
improvements seem to have levelled off and more energy is now spent
(literally) at improving rotational speed. This has the secondary
benefit of also improving transfer rates.

Some typical values:

Drive type

Access time (ms) | Fast Typical Old
---------------------------------------------
Track-to-track <1 2 8
Average seek 10 15 30
End-to-end 10 30 70

This shows that the very high end drives offer only marginally better
access times then the average drives but that the old drives based on
stepper motors are significantly worse.

Rotational speed (RPM) | 3600 | 4500 | 4800 | 5400 | 7200 | 10000
-------------------------------------------------------------------
Latency (ms) | 17 | 13 | 12.5 | 11.1 | 8.3 | 6.0

As latency is the average time taken to reach a given sector, the
formula is quite simply
latency (ms) = 60000 / speed (RPM)

Clearly this too is an example of diminishing returns for the efforts
put into development. However, what really takes off here is the power
consumption, heat and noise.

6.9. Yoke

There is also a Linux Yoke Driver <http://www.it.uc3m.es/cgi-
bin/ptb/cvs-yoke.cgi> available in beta which is intended to do hot-
swappable transparent binding of one Linux block device to another.
This means that if you bind two block devices together, say /dev/hda
and /dev/loop0, writing to one device will mean also writing to the
other and reading from either will yield the same result.

6.10. Stacking

One of the advantages of a layered design of an operating system is
that you have the flexibility to put the pieces together in a number
of ways. For instance you can cache a CD-ROM with cachefs that is a
volume striped over 2 drives. This in turn can be set up translucently
with a volume that is NFS mounted from another machine. RAID can be
stacked in several layers to offer very fast seek and transfer in such
a way that it will work if even 3 drives fail. The choices are many,
limited only by imagination and, probably more importantly, money.

6.11. Recommendations

There is a near infinite number of combinations available but my
recommendation is to start off with a simple setup without any fancy
add-ons. Get a feel for what is needed, where the maximum performance
is required, if it is access time or transfer speed that is the bottle
neck, and so on. Then phase in each component in turn. As you can
stack quite freely you should be able to retrofit most components in
as time goes by with relatively few difficulties.

RAID is usually a good idea but make sure you have a thorough grasp of
the technology and a solid back up system.

7. Other Operating Systems

Many Linux users have several operating systems installed, often
necessitated by hardware setup systems that run under other operating
systems, typically DOS or some flavour of Windows. A small section on
how best to deal with this is therefore included here.

7.1. DOS

Leaving aside the debate on weather or not DOS qualifies as an
operating system one can in general say that it has little
sophistication with respect to disk operations. The more important
result of this is that there can be severe difficulties in running
various versions of DOS on large drives, and you are therefore
strongly recommended in reading the Large Drives mini-HOWTO. One
effect is that you are often better off placing DOS on low track
numbers.

Having been designed for small drives it has a rather unsophisticated
file system (fat) which when used on large drives will allocate
enormous block sizes. It is also prone to block fragmentation which
will after a while cause excessive seeks and slow effective transfers.

One solution to this is to use a defragmentation program regularly but
it is strongly recommended to back up data and verify the disk before
defragmenting. All versions of DOS have chkdsk that can do some disk
checking, newer versions also have scandisk which is somewhat better.
There are many defragmentation programs available, some versions have
one called defrag. Norton Utilities have a large suite of disk tools
and there are many others available too.

As always there are snags, and this particular snake in our drive
paradise is called hidden files. Some vendors started to use these for
copy protection schemes and would not take kindly to being moved to a
different place on the drive, even if it remained in the same place in
the directory structure. The result of this was that newer
defragmentation programs will not touch any hidden file, which in turn
reduces the effect of defragmentation.

Being a single tasking, single threading and single most other things
operating system there is very little gains in using multiple drives
unless you use a drive controller with built in RAID support of some
kind.

There are a few utilities called join and subst which can do some
multiple drive configuration but there is very little gains for a lot
of work. Some of these commands have been removed in newer versions.

In the end there is very little you can do, but not all hope is lost.
Many programs need fast, temporary storage, and the better behaved
ones will look for environment variables called TMPDIR or TEMPDIR
which you can set to point to another drive. This is often best done
in autoexec.bat.

______________________________________________________________________
SET TMPDIR=E:/TMP
SET TEMPDIR=E:/TEMP
______________________________________________________________________

Not only will this possibly gain you some speed but also it can reduce
fragmentation.

There have been reports about difficulties in removing multiple
primary partitions using the fdisk program that comes with DOS. Should
this happen you can instead use a Linux rescue disk with Linux fdisk
to repair the system.

Don't forget there are other alternatives to DOS, the most well known
being DR-DOS <http://www.caldera.com/dos/> from Caldera
<http://www.caldera.com/>. This is a direct descendant from DR-DOS
from Digital Research. It offers many features not found in the more
common DOS, such as multi tasking and long filenames.

Another alternative which also is free is Free DOS
<http://www.freedos.org/> which is a project under development. A
number of free utilities are also available.

7.2. Windows

Most of the above points are valid for Windows too, with the exception
of Windows95 which apparently has better disk handling, which will get
better performance out of SCSI drives.

A useful thing is the introduction of long filenames, to read these
from Linux you will need the vfat file system for mounting these
partitions.

Disk fragmentation is still a problem. Some of this can be avoided by
doing a defragmentation immediately before and immediately after
installing large programs or systems. I use this scheme at work and
have found it to work quite well. Purging unused files and emptying
the waste basket first can improve defragmentation further.

Windows also use swap drives, redirecting this to another drive can
give you some performance gains. There are several mini-HOWTOs telling
you how best to share swap space between various operating systems.

The trick of setting TEMPDIR can still be used but not all programs
will honour this setting. Some do, though. To get a good overview of
the settings in the control files you can run sysedit which will open
a number of files for editing, one of which is the autoexec file where
you can add the TEMPDIR settings.

Much of the temporary files are located in the /windows/temp directory
and changing this is more tricky. To achieve this you can use regedit
which is rather powerful and quite capable of rendering your system in
a state you will not enjoy, or more precisely, in a state much less
enjoyable than windows in general. Registry database error is a
message that means seriously bad news. Also you will see that many
programs have their own private temporary directories scattered around
the system.

Setting the swap file to a separate partition is a better idea and
much less risky. Keep in mind that this partition cannot be used for
anything else, even if there should appear to be space left there.

It is now possible to read ext2fs partitions from Windows, either by
mounting the partition using FSDEXT2 <http://www.yipton.demon.co.uk/>
or by using a file explorer like tool called Explore2fs
<http://uranus.it.swin.edu.au/~jn/linux/explore2fs.htm>.

7.3. OS/2

The only special note here is that you can get file system driver for
OS/2 that can read an ext2fs partition. Matthieu Willm's ext2fs
Installable File System for OS/2 can be found at ftp-os2.nmsu.edu
<ftp://ftp-os2.nmsu.edu/pub/os2/system/drivers/filesys/ext2_240.zip>,
Sunsite
<ftp://sunsite.unc.edu/pub/Linux/system/filesystems/ext2/ext2_240.zip>,
ftp.leo.org
<ftp://ftp.leo.org/pub/comp/os/os2/drivers/ifs/ext2_240.zip> and ftp-
os2.cdrom.com <ftp://ftp-os2.cdrom.com/pub/os2/diskutil/ext2_240.zip>.

The IFS has read and write capabilities.

7.4. NT

This is a more serious system featuring most buzzwords known to
marketing. It is well worth noting that it features software striping
and other more sophisticated setups. Check out the drive manager in
the control panel. I do not have easy access to NT, more details on
this can take a bit of time.

One important snag was recently reported by acahalan at cs.uml.edu :
(reformatted from a Usenet News posting)

NT DiskManager has a serious bug that can corrupt your disk when you
have several (more than one?) extended partitions. Microsoft provides
an emergency fix program at their web site. See the knowledge base
<http://www.microsoft.com/kb/> for more. (This affects Linux users,
because Linux users have extra partitions)

You can now read ext2fs partitions from NT using Explore2fs
<http://uranus.it.swin.edu.au/~jn/linux/explore2fs.htm>.

7.5. Windows 2000

Most points regarding Windows NT also applies to its descendant
Windows 2000 though at the time of writing this I do not know if the
aforementioned bugs have been fixed or not.

While Windows 2000, like its predecessor, features RAID, at least one
company, RAID Toolbox <http://www.raidtoolbox.com/>, has found the
bundled RAID somewhat lacking and made their own commercial
alternative.

7.6. Sun OS

There is a little bit of confusion in this area between Sun OS vs.
Solaris. Strictly speaking Solaris is just Sun OS 5.x packaged with
Openwindows and a few other things. If you run Solaris, just type
uname -a to see your version. Parts of the reason for this confusion
is that Sun Microsystems used to use an OS from the BSD family,
albeight with a few bits and pieces from elsewhere as well as things
made by themselves. This was the situation up to Sun OS 4.x.y when
they did a "strategic roadmap decision" and decided to switch over to
the official Unix, System V, Release 4 (aka SVR5), and Sun OS 5 was
created. This made a lot of people unhappy. Also this was bundled
with other things and marketed under the name Solaris, which currently
stands at release 7 which just recently replaced version 2.6 as the
latest and greatest. In spite of the large jump in version number
this is actually a minor technical upgrade but a giant leap for
marketing.

7.6.1. Sun OS 4

This is quite familiar to most Linux users. The last release is 4.1.4
plus various patches. Note however that the file system structure is
quite different and does not conform to FSSTND so any planning must be
based on the traditional structure. You can get some information by
the man page on this: man hier. This is, like most man pages, rather
brief but should give you a good start. If you are still confused by
the structure it will at least be at a higher level.

7.6.2. Sun OS 5 (aka Solaris)

This comes with a snazzy installation system that runs under
Openwindows, it will help you in partitioning and formatting the
drives before installing the system from CD-ROM. It will also fail if
your drive setup is too far out, and as it takes a complete
installation run from a full CD-ROM in a 1x only drive this failure
will dawn on you after too long time. That is the experience we had
where I used to work. Instead we installed everything onto one drive
and then moved directories across.

The default settings are sensible for most things, yet there remains a
little oddity: swap drives. Even though the official manual recommends
multiple swap drives (which are used in a similar fashion as on Linux)
the default is to use only a single drive. It is recommended to change
this as soon as possible.

Sun OS 5 offers also a file system especially designed for temporary
files, tmpfs. It offers significant speed improvements over ufs but
does not survive rebooting.

The only comment so far is: beware! Under Solaris 2.0 it seem that
creating too big files in /tmp can cause an out of swap space kernel
panic trap. As the evidence of what has happened is as lost as any
data on a RAMdisk after powering down it can be hard to find out what
has happened. What is worse, it seems that user space processes can
cause this kernel panic and unless this problem is taken care of it is
best not to use tmpfs in potentially hostile environments.

Also see the notes on ``tmpfs''.

Trivia: There is a movie also called Solaris, a science fiction movie
that is very, very long, slow and incomprehensible. This was often
pointed out at the time Solaris (the OS) appeared...

7.7. BeOS

This operating system is one of the more recent one to arrive and it
features a file system that has some database like features.

There is a BFS file system driver being developed for Linux and is
available in alpha stage. For more information check the Linux BFS
page <http://hp.vector.co.jp/authors/VA008030/bfs/> where patches also
are available.

8. Clusters

In this section I will briefly touch on the ways machines can be
connected together but this is so big a topic it could be a separate
HOWTO in its own right, hint, hint. Also, strictly speaking, this
section lies outside the scope of this HOWTO, so if you feel like
getting fame etc. you could contact me and take over this part and
turn it into a new document.

These days computers gets outdated at an incredible rate. There is
however no reason why old hardware could not be put to good use with
Linux. Using an old and otherwise outdated computer as a network
server can be both useful in its own right as well as a valuable
educational exercise. Such a local networked cluster of computers can
take on many forms but to remain within the charter of this HOWTO I
will limit myself to the disk strategies. Nevertheless I would hope
someone else could take on this topic and turn it into a document on
its own.

This is an exciting area of activity today, and many forms of
clustering is available today, ranging from automatic workload
balancing over local network to more exotic hardware such as Scalable
Coherent Interface (SCI) which gives a tight integration of machines,
effectively turning them into a single machine. Various kinds of
clustering has been available for larger machines for some time and
the VAXcluster is perhaps a well known example of this. Clustering is
done usually in order to share resources such as disk drives, printers
and terminals etc, but also processing resources equally transparently
between the computational nodes.

There is no universal definition of clustering, in here it is taken to
mean a network of machines that combine their resources to serve
users. Admittedly this is a rather loose definition but this will
change later.

These days also Linux offers some clustering features but for a
starter I will just describe a simple local network. It is a good way
of putting old and otherwise unusable hardware to good use, as long as
they can run Linux or something similar.

One of the best ways of using an old machine is as a network server in
which case the effective speed is more likely to be limited by network
bandwidth rather than pure computational performance. For home use you
can move the following functionality off to an older machine used as a
server:

· news

· mail

· web proxy

· printer server

· modem server (PPP, SLIP, FAX, Voice mail)

You can also NFS mount drives from the server onto your workstation
thereby reducing drive space requirements. Still read the FSSTND to
see what directories should not be exported. The best candidates for
exporting to all machines are /usr and /var/spool and possibly
/usr/local but probably not /var/spool/lpd.

Most of the time even slow disks will deliver sufficient performance.
On the other hand, if you do processing directly on the disks on the
server or have very fast networking, you might want to rethink your
strategy and use faster drives. Searching features on a web server or
news database searches are two examples of this.

Such a network can be an excellent way of learning system
administration and building up your own toaster network, as it often
is called. You can get more information on this in other HOWTOs but
there are two important things you should keep in mind:

· Do not pull IP numbers out of thin air. Configure your inside net
using IP numbers reserved for private use, and use your network
server as a router that handles this IP masquerading.

· Remember that if you additionally configure the router as a
firewall you might not be able to get to your own data from the
outside, depending on the firewall configuration.

The Nyx network provides an example of a cluster in the sense defined
here. It consists of the following machines:

nyx
is one of the two user login machines and also provides some of
the networking services.

nox
(aka nyx10) is the main user login machine and is also the mail
server.

noc
is a dedicated news server. The news spool is made accessible
through NFS mounting to nyx and nox.

arachne
(aka www) is the web server. Web pages are written by NFS
mounting onto nox.

There are also some more advanced clustering projects going, notably

· The Beowulf Project <http://www.beowulf.org/>

· The Genoa Active Message Machine (GAMMA)
<http://www.disi.unige.it/project/gamma/>

High-tech clustering requires high-tech interconnect, and SCI is one
of them. To find out more you can either look up the home page of
Dolphin Interconnect Solutions <http://www.dolphinics.no/> which is
one of the main actors in this field, or you can have a look at scizzl
<http://www.scizzl.com/>.

Centralised mail servers using IMAP are becoming more and more popular
as disks become large enough to keep all mail stored indefinitely and
also cheap enough to make it a feasible option. Unfortunately it has
become clear that NFS mounting the mail archives from another machine
can cause corruption of the IMAP database as the server software does
not handle NFS timeouts too well, and NFS timeouts are a rather common
occurrence. Keep therefore the mail archive local to the IMAP server.

9. Mount Points

In designing the disk layout it is important not to split off the
directory tree structure at the wrong points, hence this section. As
it is highly dependent on the FSSTND it has been put aside in a
separate section, and will most likely have to be totally rewritten
when FHS is adopted in a Linux distribution. In the meanwhile this
will do.

Remember that this is a list of where a separation can take place, not
where it has to be. As always, good judgement is always required.

Again only a rough indication can be given here. The values indicate

0=don't separate here
1=not recommended
...
4=useful
5=recommended

In order to keep the list short, the uninteresting parts are removed.

Directory Suitability
/
|
+-bin 0
+-boot 5
+-dev 0
+-etc 0
+-home 5
+-lib 0
+-mnt 0
+-proc 0
+-root 0
+-sbin 0
+-tmp 5
+-usr 5
| \
| +-X11R6 3
| +-bin 3
| +-lib 4
| +-local 4
| | \
| | +bin 2
| | +lib 4
| +-src 3
|
+-var 5
\
+-adm 0
+-lib 2
+-lock 1
+-log 0
+-preserve 1
+-run 1
+-spool 4
| \
| +-mail 3
| +-mqueue 3
| +-news 5
| +-smail 3
| +-uucp 3
+-tmp 5

There is of course plenty of adjustments possible, for instance a home
user would not bother with splitting off the /var/spool hierarchy but
a serious ISP should. The key here is usage.

QUIZ! Why should /etc never be on a separate partition? Answer:
Mounting instructions during boot is found in the file /etc/fstab so
if this is on a separate and unmounted partition it is like the key to
a locked drawer is inside that drawer, a hopeless situation. (Yes,
I'll do nearly anything to liven up this HOWTO.)

10. Considerations and Dimensioning

The starting point in this will be to consider where you are and what
you want to do. The typical home system starts out with existing
hardware and the newly converted Linux user will want to get the most
out of existing hardware. Someone setting up a new system for a
specific purpose (such as an Internet provider) will instead have to
consider what the goal is and buy accordingly. Being ambitious I will
try to cover the entire range.

Various purposes will also have different requirements regarding file
system placement on the drives, a large multiuser machine would
probably be best off with the /home directory on a separate disk, just
to give an example.

In general, for performance it is advantageous to split most things
over as many disks as possible but there is a limited number of
devices that can live on a SCSI bus and cost is naturally also a
factor. Equally important, file system maintenance becomes more
complicated as the number of partitions and physical drives increases.

10.1. Home Systems

With the cheap hardware available today it is possible to have quite a
big system at home that is still cheap, systems that rival major
servers of yesteryear. While many started out with old, discarded
disks to build a Linux server (which is how this HOWTO came into
existence), many can now afford to buy 40 GB disks up front.

Size remains important for some, and here are a few guidelines:

Testing
Linux is simple and you don't even need a hard disk to try it
out, if you can get the boot floppies to work you are likely to
get it to work on your hardware. If the standard kernel does not
work for you, do not forget that often there can be special boot
disk versions available for unusual hardware combinations that
can solve your initial problems until you can compile your own
kernel.

Learning
about operating system is something Linux excels in, there is
plenty of documentation and the source is available. A single
drive with 50 MB is enough to get you started with a shell, a
few of the most frequently used commands and utilities.

Hobby
use or more serious learning requires more commands and
utilities but a single drive is still all it takes, 500 MB
should give you plenty of room, also for sources and
documentation.

Serious
software development or just serious hobby work requires even
more space. At this stage you have probably a mail and news feed
that requires spool files and plenty of space. Separate drives
for various tasks will begin to show a benefit. At this stage
you have probably already gotten hold of a few drives too. Drive
requirements gets harder to estimate but I would expect 2-4 GB
to be plenty, even for a small server.

Servers
come in many flavours, ranging from mail servers to full sized
ISP servers. A base of 2 GB for the main system should be
sufficient, then add space and perhaps also drives for separate
features you will offer. Cost is the main limiting factor here
but be prepared to spend a bit if you wish to justify the "S" in
ISP. Admittedly, not all do it.

Basically a server is dimensioned like any machine for serious
use with added space for the services offered, and tends to be
IO bound rather than CPU bound.

With cheap networking technology both for land lines as well as
through radio nets, it is quite likely that very soon home users
will have their own servers more or less permanently hooked onto
the net.

10.2. Servers

Big tasks require big drives and a separate section here. If possible
keep as much as possible on separate drives. Some of the appendices
detail the setup of a small departmental server for 10-100 users. Here
I will present a few consideration for the higher end servers. In
general you should not be afraid of using RAID, not only because it is
fast and safe but also because it can make growth a little less
painful. All the notes below come as additions to the points mentioned
earlier.

Popular servers rarely just happens, rather they grow over time and
this demands both generous amounts of disk space as well as a good net
connection. In many of these cases it might be a good idea to reserve
entire SCSI drives, in singles or as arrays, for each task. This way
you can move the data should the computer fail. Note that transferring
drives across computers is not simple and might not always work,
especially in the case of IDE drives. Drive arrays require careful
setup in order to reconstruct the data correctly, so you might want to
keep a paper copy of your fstab file as well as a note of SCSI IDs.

10.2.1. Home Directories

Estimate how many drives you will need, if this is more than 2 I would
recommend RAID, strongly. If not you should separate users across your
drives dedicated to users based on some kind of simple hashing
algorithm. For instance you could use the first 2 letters in the user
name, so jbloggs is put on /u/j/b/jbloggs where /u/j is a symbolic
link to a physical drive so you can get a balanced load on your
drives.

10.2.2. Anonymous FTP

This is an essential service if you are serious about service. Good
servers are well maintained, documented, kept up to date, and
immensely popular no matter where in the world they are located. The
big server ftp.funet.fi <ftp://ftp.funet.fi> is an excellent example
of this.

In general this is not a question of CPU but of network bandwidth.
Size is hard to estimate, mainly it is a question of ambition and
service attitudes. I believe the big archive at ftp.cdrom.com
<ftp://ftp.cdrom.com> is a *BSD machine with 50 GB disk. Also memory
is important for a dedicated FTP server, about 256 MB RAM would be
sufficient for a very big server, whereas smaller servers can get the
job done well with 64 MB RAM. Network connections would still be the
most important factor.

10.2.3. WWW

For many this is the main reason to get onto the Internet, in fact
many now seem to equate the two. In addition to being network
intensive there is also a fair bit of drive activity related to this,
mainly regarding the caches. Keeping the cache on a separate, fast
drive would be beneficial. Even better would be installing a caching
proxy server. This way you can reduce the cache size for each user and
speed up the service while at the same time cut down on the bandwidth
requirements.

With a caching proxy server you need a fast set of drives, RAID0 would
be ideal as reliability is not important here. Higher capacity is
better but about 2 GB should be sufficient for most. Remember to match
the cache period to the capacity and demand. Too long periods would on
the other hand be a disadvantage, if possible try to adjust based on
the URL. For more information check up on the most used servers such
as Harvest, Squid <http://www.squid-cache.org/> and the one from
Netscape <http://www.netscape.com>.

10.2.4. Mail

Handling mail is something most machines do to some extent. The big
mail servers, however, come into a class of their own. This is a
demanding task and a big server can be slow even when connected to
fast drives and a good net feed. In the Linux world the big server at
vger.rutgers.edu is a well known example. Unlike a news service which
is distributed and which can partially reconstruct the spool using
other machines as a feed, the mail servers are centralised. This makes
safety much more important, so for a major server you should consider
a RAID solution with emphasize on reliability. Size is hard to
estimate, it all depends on how many lists you run as well as how many
subscribers you have.

Big mail servers can be IO limited in performance and for this reason
some use huge silicon disks connected to the SCSI bus to hold all mail
related files including temporary files. For extra safety these are
battery backed and filesystems like udf are preferred since they
always flush metadata to disk. This added cost to performance is
offset by the very fast disk.

Note that these days more and more switch over from using POP to pull
mail to local machine from mail server and instead use IMAP to serve
mail while keeping the mail archive centralised. This means that mail
is no longer spooled in its original sense but often builds up,
requiring huge disk space. Also more and more (ab)use mail attachments
to send all sorts of things across, even a small word processor
document can easily end up over 1 MB. Size your disks generously and
keep an eye on how much space is left.
10.2.5. News

This is definitely a high volume task, and very dependent on what news
groups you subscribe to. On Nyx there is a fairly complete feed and
the spool files consume about 17 GB. The biggest groups are no doubt
in the alt.binary.* hierarchy, so if you for some reason decide not to
get these you can get a good service with perhaps 12 GB. Still others,
that shall remain nameless, feel 2 GB is sufficient to claim ISP
status. In this case news expires so fast I feel the spelling IsP is
barely justified. A full newsfeed means a traffic of a few GB every
day and this is an ever growing number.

10.2.6. Others

There are many services available on the net and even though many have
been put somewhat in the shadows by the web. Nevertheless, services
like archie, gopher and wais just to name a few, still exist and
remain valuable tools on the net. If you are serious about starting a
major server you should also consider these services. Determining the
required volumes is hard, it all depends on popularity and demand.
Providing good service inevitably has its costs, disk space is just
one of them.

10.2.7. Server Recommendations

Servers today require large numbers of large disks to function
satisfactorily in commercial settings. As mean time between failure
(MTBF) decreases rapidly as the number of components increase it is
advisable to look into using RAID for protection and use a number of
medium sized drives rather than one single huge disk. Also look into
the High Availability (HA) project for more information. More
information is available at

High Availability HOWTO <http://www.ibiblio.org/pub/Linux/ALPHA/linux-
ha/High-Availability-HOWTO.html> and also at related web pages
<http://www.henge.com/~alanr/ha/index.html>.

There is also an article in Byte called How Big Does Your Unix Server
Have To Be?
<http://www.byte.com/columns/servinglinux/1999/06/0607servinglinux.html>
with many points that are relevant to Linux.

10.3. Pitfalls

The dangers of splitting up everything into separate partitions are
briefly mentioned in the section about volume management. Still,
several people have asked me to emphasize this point more strongly:
when one partition fills up it cannot grow any further, no matter if
there is plenty of space in other partitions.

In particular look out for explosive growth in the news spool
(/var/spool/news). For multi user machines with quotas keep an eye on
/tmp and /var/tmp as some people try to hide their files there, just
look out for filenames ending in gif or jpeg...

In fact, for single physical drives this scheme offers very little
gains at all, other than making file growth monitoring easier (using
'df') and physical track positioning. Most importantly there is no
scope for parallel disk access. A freely available volume management
system would solve this but this is still some time in the future.
However, when more specialised file systems become available even a
single disk could benefit from being divided into several partitions.

For more information see section ``Troubleshooting''.

11. Disk Layout

With all this in mind we are now ready to embark on the layout. I have
based this on my own method developed when I got hold of 3 old SCSI
disks and boggled over the possibilities.

The tables in the appendices are designed to simplify the mapping
process. They have been designed to help you go through the process of
optimizations as well as making an useful log in case of system
repair. A few examples are also given.

11.1. Selection for Partitioning

Determine your needs and set up a list of all the parts of the file
system you want to be on separate partitions and sort them in
descending order of speed requirement and how much space you want to
give each partition.

The table in ``Appendix A'' section is a useful tool to select what
directories you should put on different partitions. It is sorted in a
logical order with space for your own additions and notes about
mounting points and additional systems. It is therefore NOT sorted in
order of speed, instead the speed requirements are indicated by
bullets ('o').

If you plan to RAID make a note of the disks you want to use and what
partitions you want to RAID. Remember various RAID solutions offers
different speeds and degrees of reliability.

(Just to make it simple I'll assume we have a set of identical SCSI
disks and no RAID)

11.2. Mapping Partitions to Drives

Then we want to place the partitions onto physical disks. The point of
the following algorithm is to maximise parallelizing and bus capacity.
In this example the drives are A, B and C and the partitions are
987654321 where 9 is the partition with the highest speed requirement.
Starting at one drive we 'meander' the partition line over and over
the drives in this way:

A : 9 4 3
B : 8 5 2
C : 7 6 1

This makes the 'sum of speed requirements' the most equal across each
drive.

Use the table in ``Appendix B'' section to select what drives to use
for each partition in order to optimize for paralellicity.

Note the speed characteristics of your drives and note each directory
under the appropriate column. Be prepared to shuffle directories,
partitions and drives around a few times before you are satisfied.

11.3. Sorting Partitions on Drives

After that it is recommended to select partition numbering for each
drive.

Use the table in ``Appendix C'' section to select partition numbers in
order to optimize for track characteristics. At the end of this you
should have a table sorted in ascending partition number. Fill these
numbers back into the tables in appendix A and B.

You will find these tables useful when running the partitioning
program (fdisk or cfdisk) and when doing the installation.

11.4. Optimizing

After this there are usually a few partitions that have to be
'shuffled' over the drives either to make them fit or if there are
special considerations regarding speed, reliability, special file
systems etc. Nevertheless this gives what this author believes is a
good starting point for the complete setup of the drives and the
partitions. In the end it is actual use that will determine the real
needs after we have made so many assumptions. After commencing
operations one should assume a time comes when a repartitioning will
be beneficial.

For instance if one of the 3 drives in the above mentioned example is
very slow compared to the two others a better plan would be as
follows:

A : 9 6 5
B : 8 7 4
C : 3 2 1

11.4.1. Optimizing by Characteristics

Often drives can be similar in apparent overall speed but some
advantage can be gained by matching drives to the file size
distribution and frequency of access. Thus binaries are suited to
drives with fast access that offer command queueing, and libraries are
better suited to drives with larger transfer speeds where IDE offers
good performance for the money.

11.4.2. Optimizing by Drive Parallelising

Avoid drive contention by looking at tasks: for instance if you are
accessing /usr/local/bin chances are you will soon also need files
from /usr/local/lib so placing these at separate drives allows less
seeking and possible parallel operation and drive caching. It is quite
possible that choosing what may appear less than ideal drive
characteristics will still be advantageous if you can gain parallel
operations. Identify common tasks, what partitions they use and try to
keep these on separate physical drives.

Just to illustrate my point I will give a few examples of task
analysis here.

Office software
such as editing, word processing and spreadsheets are typical
examples of low intensity software both in terms of CPU and disk
intensity. However, should you have a single server for a huge
number of users you should not forget that most such software
have auto save facilities which cause extra traffic, usually on
the home directories. Splitting users over several drives would
reduce contention.

News
readers also feature auto save features on home directories so
ISPs should consider separating home directories

News spools are notorious for their deeply nested directories
and their large number of very small files. Loss of a news spool
partition is not a big problem for most people, too, so they are
good candidates for a RAID 0 setup with many small disks to
distribute the many seeks among multiple spindles. It is
recommended in the manuals and FAQs for the INN news server to
put news spool and .overview files on separate drives for larger
installations.

Some notes on INN optimising under Tru64 UNIX
<http://www.tru64unix.compaq.com/internet/inn-wp.html> also
applies to a wider audience, including Linux users.

Database
applications can be demanding both in terms of drive usage and
speed requirements. The details are naturally application
specific, read the documentation carefully with disk
requirements in mind. Also consider RAID both for performance
and reliability.

E-mail
reading and sending involves home directories as well as in- and
outgoing spool files. If possible keep home directories and
spool files on separate drives. If you are a mail server or a
mail hub consider putting in- and outgoing spool directories on
separate drives.

Losing mail is an extremely bad thing, if you are managing an
ISP or major hub. Think about RAIDing your mail spool and
consider frequent backups.

Software development
can require a large number of directories for binaries,
libraries, include files as well as source and project files. If
possible split as much as possible across separate drives. On
small systems you can place /usr/src and project files on the
same drive as the home directories.
Web browsing
is becoming more and more popular. Many browsers have a local
cache which can expand to rather large volumes. As this is used
when reloading pages or returning to the previous page, speed is
quite important here. If however you are connected via a well
configured proxy server you do not need more than typically a
few megabytes per user for a session. See also the sections on
``Home Directories'' and ``WWW''.

11.5. Compromises

One way to avoid the aforementioned ``pitfalls'' is to only set off
fixed partitions to directories with a fairly well known size such as
swap, /tmp and /var/tmp and group together the remainders into the
remaining partitions using symbolic links.

Example: a slow disk (slowdisk), a fast disk (fastdisk) and an
assortment of files. Having set up swap and tmp on fastdisk; and /home
and root on slowdisk we have (the fictitious) directories /a/slow,
/a/fast, /b/slow and /b/fast left to allocate on the partitions
/mnt.slowdisk and /mnt.fastdisk which represents the remaining
partitions of the two drives.

Putting /a or /b directly on either drive gives the same properties to
the subdirectories. We could make all 4 directories separate
partitions but would lose some flexibility in managing the size of
each directory. A better solution is to make these 4 directories
symbolic links to appropriate directories on the respective drives.

Thus we make

/a/fast point to /mnt.fastdisk/a/fast or /mnt.fastdisk/a.fast
/a/slow point to /mnt.slowdisk/a/slow or /mnt.slowdisk/a.slow
/b/fast point to /mnt.fastdisk/b/fast or /mnt.fastdisk/b.fast
/b/slow point to /mnt.slowdisk/b/slow or /mnt.slowdisk/b.slow

and we get all fast directories on the fast drive without having to
set up a partition for all 4 directories. The second (right hand)
alternative gives us a flatter files system which in this case can
make it simpler to keep an overview of the structure.

The disadvantage is that it is a complicated scheme to set up and plan
in the first place and that all mount points and partitions have to be
defined before the system installation.

Important: note that the /usr partition must be mounted directly onto
root and not via an indirect link as described above. The reason for
this are the long backward links used extensively in X11 that go from
deep within /usr all the way to root and then down into /etc
directories.

12. Implementation

Having done the layout you should now have a detailed description on
what goes where. Most likely this will be on paper but hopefully
someone will make a more automated system that can deal with
everything from the design, through partitioning to formatting and
installation. This is the route one will have to take to realise the
design.

Modern distributions come with installation tools that will guide you
through partitioning and formatting and also set up /etc/fstab for you
automatically. For later modifications, however, you will need to
understand the underlying mechanisms.

12.1. Checklist

Before starting make sure you have the following:

· Written notes of what goes where, your design

· A functioning, tested rescue disk

· A fresh backup of your precious data

· At least two formatted, tested and empty floppies

· Read and understood the man page for fdisk or equivalent

· Patience, concentration and elbow grease

12.2. Drives and Partitions

When you start DOS or the like you will find all partitions labeled C:
and onwards, with no differentiation on IDE, SCSI, network or whatever
type of media you have. In the world of Linux this is rather
different. During booting you will see partitions described like this:

______________________________________________________________________
Dec 6 23:45:18 demos kernel: Partition check:
Dec 6 23:45:18 demos kernel: sda: sda1
Dec 6 23:45:18 demos kernel: hda: hda1 hda2
______________________________________________________________________

SCSI drives are labelled sda, sdb, sdc etc, and (E)IDE drives are
labelled hda, hdb, hdc etc. There are also standard names for all
devices, full information can be found in /dev/MAKEDEV and
/usr/src/linux/Documentation/devices.txt.

Partitions are labelled numerically for each drive hda1, hda2 and so
on. On SCSI drives there can be 15 partitions per drive, on EIDE
drives there can be 63 partitions per drive. Both limits exceed what
is currently useful for most disks.

These are then mounted according to the file /etc/fstab before they
appear as a part of the file system.

12.3. Partitioning

It feels so good / It's a marginal risk / when I clear off / windows
with fdisk! (the Dustbunny in an issue
<http://www.userfriendly.org/cartoons/archives/99feb/19990221.html> of
User Friendly <http://www.userfriendly.org/> in the song "Refund
this")

First you have to partition each drive into a number of separate
partitions. Under Linux there are two main methods, fdisk and the
more screen oriented cfdisk. These are complex programs, read the
manual very carefully. For the experts there is now also sfdisk.

Partitions come in 3 flavours, primary, extended and logical. You
have to use primary partitions for booting, but there is a maximum of
4 primary partitions. If you want more you have to define an extended
partition within which you define your logical partitions.

Each partition has an identifier number which tells the operating
system what it is, for Linux the types swap(82) and ext2fs(83) are the
ones you will need to know. If you want to use RAID with autostart
you have to check the documentation for the appropriate type number
for the RAID partition.

There is a readme file that comes with fdisk that gives more in-depth
information on partitioning.

Someone has just made a Partitioning HOWTO which contains excellent,
in depth information on the nitty-gritty of partitioning. Rather than
repeating it here and bloating this document further, I will instead
refer you to it instead.

Redhat has written a screen oriented utility called Disk Druid which
is supposed to be a user friendly alternative to fdisk and cfdisk and
also automates a few other things. Unfortunately this product is not
quite mature so if you use it and cannot get it to work you are well
advised to try fdisk or cfdisk.

Not to be outdone, Mandrakesoft has made an even more graphic
alternative called Diskdrake <http://www.linux-
mandrake.com/diskdrake/> that also offers numerous features.

Also the GNU project offers a partitioning tool called GNU Parted
<http://www.gnu.org/software/parted/>

The Ranish Partition Manager
<http://www.users.intercom.com/~ranish/part/> is another free
alternative, while Partition Magic <http://www.powerquest.com> is a
popular commercial alternative which also offers some support for
resizing ext2fs partitions.

Note that Windows will complain if it finds more than one primary
partition on a drive. Also it appears to assign drive letters to
primary partitions as it finds disks before starting over from the
first disk to assign subsequent drive names to logical partitions.

If you want DOS/Windows on your system you should make that partition
first, a primary one to boot to, made with the DOS fdisk program.
Then if you want NT you put that one in. Finally, for Linux, you
create those partitions with the Linux fdisk program or equivalents.
Linux is flexible enough to boot from both primary as well as logical
partitions.

In depth information on DOS fdisk can be found at Fdisk.com
<http://www.fdisk.com/fdisk/> and MS-DOS 5.00 - 7.10 Undocumented,
Secret + Hidden Features <http://members.aol.com/axcel216/secrets.htm>
which details even more bugs and pitfalls.

12.4. Repartitioning

Sometimes it is necessary to change the sizes of existing partitions
while keeping the contents intact. One way is of course to back up
everything, recreate new partitions and then restore the old contents,
and while this gives your back up system a good test it is also rather
time consuming.

Partition resizing is a simpler alternative where a file system is
first shrunk to desired volume and then the partition table is updated
to reflect the new end of partition position. This process is
therefore very file system sensitive.

Repartitioning requires there to be free space at the end of the file
space so to ensure you are able to shrink the size you should first
defragment your drive and empty any wastebaskets.

Using fips <http://www.igd.fhg.de/~aschaefe/fips/> you can resize a
fat partition, and the latest version 1.6 of fips or fips 2.0 are also
able to resize fat32 partition. Note that these programs actually run
under DOS.

Resizing other file systems are much more complicated but one popular
commercial system Partition Magic <http://www.powerquest.com> is able
to resize more file system types, including ext2fs using the resize2fs
program. Make sure you get the latest updates to this program as
recent versions had problems with large disks.

In order to get the most out of fips you should first delete
unnecessary files, empty wastebaskets etc. before defragmenting your
drive. This way you can allocate more space to other partitions. If
the program complains there are still files at the end of your drive
it is probably hidden files generated by Microsoft Mirror or Norton
Image. These are probably called image.idx and image.dat and contain
backups of some system files.

There are reports that in some Windows defragmentation programs you
should make sure the box "allow Windows to move files around" is not
checked, otherwise you will end up with some files in the last
cylinder of the partition which will prevent FIPS from reclaiming
space.

If you still have unmovable files at the end of your DOS partition you
should get the DOS program showfat
<http://www8.pair.com/dmurdoch/programs/showfat.htm> version 3.0 or
higher. This shows you what files are where so you can deal with them
directly.

A freeware alternative is Partition Resizer
<http://members.nbci.com/Zeleps/> which can shrink, grow and move
partitions.

Some versions of DOS / Windows have a hidden flag for defrag, "/P that
causes defrag to move even hidden files. Use at own risk.

Repartitioning is as dangerous process as any other partitioning so
you are advised to have a fresh backup handy.

12.5. Microsoft Partition Bug

In Microsoft products all the way up to Win 98 there is a tricky bug
that can cause you a bit of trouble: if you have several primary fat
partitions and the last extended partition is not a fat partition the
Microsoft system will try to mount the last partition as if it were a
FAT partition in place of the last primary FAT partition.

There is more information <http://www.v-com.com/> available on the net
on this.

To avoid this you can place a small logical fat partition at the very
end of your disk.

More information on multi OS installations are available at V
Communications <http://www.v-com.com/> but they keep rearranging the
links continuously so no direct links can be offered here.

Since some hardware comes with setup software that is available under
DOS only this could come in handy anyway. Notable examples are RAID
controllers from DPT and a number of networking cards.

12.6. Multiple Devices ( md )

Being in a state of flux you should make sure to read the latest
documentation on this kernel feature. It is not yet stable, beware.

Briefly explained it works by adding partitions together into new
devices md0, md1 etc. using mdadd before you activate them using
mdrun. This process can be automated using the file /etc/mdtab.

The latest md system uses a /etc/raidtab and a different syntax. Make
sure your RAID-tools package matches the md version as the internal
protocol has changed.

Then you then treat these like any other partition on a drive. Proceed
with formatting etc. as described below using these new devices.

There is now also a HOWTO in development for RAID using md you should
read.

12.7. Formatting

Next comes partition formatting, putting down the data structures that
will describe the files and where they are located. If this is the
first time it is recommended you use formatting with verify. Strictly
speaking it should not be necessary but this exercises the I/O hard
enough that it can uncover potential problems, such as incorrect
termination, before you store your precious data. Look up the command
mkfs for more details.

Linux can support a great number of file systems, rather than
repeating the details you can read the man page for fs which describes
them in some details. Note that your kernel has to have the drivers
compiled in or made as modules in order to be able to use these
features. When the time comes for kernel compiling you should read
carefully through the file system feature list. If you use make
menuconfig you can get online help for each file system type.

Note that some rescue disk systems require minix, msdos and ext2fs to
be compiled into the kernel.

Also swap partitions have to be prepared, and for this you use mkswap.

Some important notes on formatting with DOS and Windows can be found
in MS-DOS 5.00 - 7.10 Undocumented, Secret + Hidden Features
<http://members.aol.com/axcel216/secrets.htm>.

Note that this formatting is high level formatting, that writes the
file system to the disk, as opposed to low level formatting that lays
down tracks and sectors. The latter is hardly ever needed these days.

12.8. Mounting

Data on a partition is not available to the file system until it is
mounted on a mount point. This can be done manually using mount or
automatically during booting by adding appropriate lines to
/etc/fstab. Read the manual for mount and pay close attention to the
tabulation.

12.9. fstab

During the booting process the system mounts all partitions as
described in the fstab file which can look something like this:

# <file system> <mount point> <type> <options> <dump> <pass>
/dev/hda2 / ext2 defaults 0 1
None none swap sw 0 0
proc /proc proc defaults 0 0
/dev/hda1 /dosc vfat defaults 0 1

This file is somewhat sensitive to the formatting used so it is best
and also most convenient to edit it using one of the editing tools
made for this purpose, such as on the netfstool
<http://www.bit.net.au/~bhepple/fstool/>, a Tcl/Tk-based file system
mounter, and kfstab <http://kfstab.purespace.de/kfstab/>, an editing
tool for KDE.

Briefly, the fields are partition name, where to mount the partition,
type of file system, mount options, when to dump for backup and when
to do fsck.

Linux offers the possibility of parallel file checking (fsck) but to
be efficient it is important not to fsck more than one partition on a
drive at a time.

12.10. Mount options

Mounting, either by hand or using the fstab, allows for a number of
options that offers extra protection. Below are some of the more
useful options.

nodev
Do not interpret character or block special devices on the file
system.

noexec
This disallows execution of any binaries on the mounted file
system. Useful in spool areas.
nosuid
This disallows set-user-identifier or set-group-identifier on
the mounted file system. Useful in home directories.

For more information and cautions refer to the man page for mount and
fstab.

12.11. Recommendations

Having constructed and implemented your clever scheme you are well
advised to make a complete record of it all, on paper. After all
having all the necessary information on disk is no use if the machine
is down.

Partition tables can be damaged or lost, in which case it is
excruciatingly important that you enter the exact same numbers into
fdisk so you can rescue your system. You can use the program printpar
to make a clear record of the tables. Also write down the SCSI numbers
or IDE names for each disk so you can put the system together again in
the right order.

There is also a small script in appendix ``Appendix M: Disk System
Documenter'' which will generate a summary of your disk
configurations.

For checking your hard disks you can use the Disk Advisor boot disk
available on the net <http://www.ontrack.com/>. The disk builder
required Windows to run. This system is useful to diagnose failed
disks.

You are strongly recommended to make a rescue disk and test it. Most
distributions make on available and is often part of the installation
disks. For some, such as the one for Redhat 6.1 the way to invoke the
disk as a rescue disk is to type linux rescue at the boot prompt.

There are also specialised rescue disk distributions available on the
net.

When need for it comes you will need to know where your root and boot
partitions reside which you need to write down and keep safe.

Note: the difference between a boot disk and a rescue disk is that a
boot disk will fail if it cannot mount the file system, typically on
your hard disk. A rescue disk is self contained and will work even if
there are no hard disks.

13. Maintenance

It is the duty of the system manager to keep an eye on the drives and
partitions. Should any of the partitions overflow, the system is
likely to stop working properly, no matter how much space is available
on other partitions, until space is reclaimed.

Partitions and disks are easily monitored using df and should be done
frequently, perhaps using a cron job or some other general system
management tool.

Do not forget the swap partitions, these are best monitored using one
of the memory statistics programs such as free, procinfo or top.

Drive usage monitoring is more difficult but it is important for the
sake of performance to avoid contention - placing too much demand on a
single drive if others are available and idle.

It is important when installing software packages to have a clear idea
where the various files go. As previously mentioned GCC keeps binaries
in a library directory and there are also other programs that for
historical reasons are hard to figure out, X11 for instance has an
unusually complex structure.

When your system is about to fill up it is about time to check and
prune old logging messages as well as hunt down core files. Proper use
of ulimit in global shell settings can help saving you from having
core files littered around the system.

13.1. Backup

The observant reader might have noticed a few hints about the
usefulness of making backups. Horror stories are legio about accidents
and what happened to the person responsible when the backup turned out
to be non-functional or even non existent. You might find it simpler
to invest in proper backups than a second, secret identity.

There are many options and also a mini-HOWTO ( Backup-With-MSDOS )
detailling what you need to know. In addition to the DOS specifics it
also contains general information and further leads.

In addition to making these backups you should also make sure you can
restore the data. Not all systems verify that the data written is
correct and many administrators have started restoring the system
after an accident happy in the belief that everything is working, only
to discover to their horror that the backups were useless. Be careful.

There are both free and commercial backup systems available for Linux.
One commercial example is the disk image level backup system from
QuickStart <http://www.estinc.com/> offering a full function 30 day
Linux demo available online.

13.2. Defragmentation

This is very dependent on the file system design, some suffer fast and
nearly debilitating fragmentation. Fortunately for us, ext2fs does not
belong to this group and therefore there has been very little talk
about defragmentation tools. It does in fact exist but is hardly ever
needed.

If for some reason you feel this is necessary, the quick and easy
solution is to do a backup and a restore. If only a small area is
affected, for instance the home directories, you could tar it over to
a temporary area on another partition, verify the archive, delete the
original and then untar it back again.

13.3. Deletions

Quite often disk space shortages can be remedied simply by deleting
unnecessary files that accumulate around the system. Quite often
programs that terminate abnormally cause all kinds of mess lying
around the oddest places. Normally a core dump results after such an
incident and unless you are going to debug it you can simply delete
it. These can be found everywhere so you are advised to do a global
search for them now and then. The locate command is useful for this.

Unexpected termination can also cause all sorts of temporary files
remaining in places like /tmp or /var/tmp, files that are
automatically removed when the program ends normally. Rebooting cleans
up some of these areas but not necessary all and if you have a long
uptime you could end up with a lot of old junk. If space is short you
have to delete with care, make sure the file is not in active use
first. Utilities like file can often tell you what kind of file you
are looking at.

Many things are logged when the system is running, mostly to files in
the /var/log area. In particular the file /var/log/messages tends to
grow until deleted. It is a good idea to keep a small archive of old
log files around for comparison should the system start to behave
oddly.

If the mail or news system is not working properly you could have
excessive growth in their spool areas, /var/spool/mail and
/var/spool/news respectively. Beware of the overview files as these
have a leading dot which makes them invisible to ls -l, it is always
better to use ls -Al which will reveal them.

User space overflow is a particularly tricky topic. Wars have been
waged between system administrators and users. Tact, diplomacy and a
generous budget for new drives is what is needed. Make use of the
message-of-the-day feature, information displayed during login from
the /etc/motd file to tell users when space is short. Setting the
default shell settings to prevent core files being dumped can save you
a lot of work too.

Certain kinds of people try to hide files around the system, usually
trying to take advantage of the fact that files with a leading dot in
the name are invisible to the ls command. One common example are
files that look like ... that normally either are not seen, or, when
using ls -al disappear in the noise of normal files like . or .. that
are in every directory. There is however a countermeasure to this,
use ls -Al that suppresses . or .. but shows all other dot-files.

13.4. Upgrades

No matter how large your drives, time will come when you will find you
need more. As technology progresses you can get ever more for your
money. At the time of writing this, it appears that 6.4 GB drives
gives you the most bang for your bucks.

Note that with IDE drives you might have to remove an old drive, as
the maximum number supported on your mother board is normally only 2
or some times 4. With SCSI you can have up to 7 for narrow (8-bit)
SCSI or up to 15 for wide (15 bit) SCSI, per channel. Some host
adapters can support more than a single channel and in any case you
can have more than one host adapter per system. My personal
recommendation is that you will most likely be better off with SCSI in
the long run.

The question comes, where should you put this new drive? In many cases
the reason for expansion is that you want a larger spool area, and in
that case the fast, simple solution is to mount the drive somewhere
under /var/spool. On the other hand newer drives are likely to be
faster than older ones so in the long run you might find it worth your
time to do a full reorganizing, possibly using your old design sheets.

If the upgrade is forced by running out of space in partitions used
for things like /usr or /var the upgrade is a little more involved.
You might consider the option of a full re-installation from your
favourite (and hopefully upgraded) distribution. In this case you will
have to be careful not to overwrite your essential setups. Usually
these things are in the /etc directory. Proceed with care, fresh
backups and working rescue disks. The other possibility is to simply
copy the old directory over to the new directory which is mounted on a
temporary mount point, edit your /etc/fstab file, reboot with your new
partition in place and check that it works. Should it fail you can
reboot with your rescue disk, re-edit /etc/fstab and try again.

Until volume management becomes available to Linux this is both
complicated and dangerous. Do not get too surprised if you discover
you need to restore your system from a backup.

The Tips-HOWTO gives the following example on how to move an entire
directory structure across:

______________________________________________________________________
(cd /source/directory; tar cf - . ) | (cd /dest/directory; tar xvfp -)
______________________________________________________________________

While this approach to moving directory trees is portable among many
Unix systems, it is inconvenient to remember. Also, it fails for
deeply nested directory trees when pathnames become to long to handle
for tar (GNU tar has special provisions to deal with long pathnames).

If you have access to GNU cp (which is always the case on Linux
systems), you could as well use

______________________________________________________________________
cp -av /source/directory /dest/directory
______________________________________________________________________

GNU cp knows specifically about symbolic links, hard links, FIFOs and
device files and will copy them correctly.

Remember that it might not be a good idea to try to transfer /dev or
/proc.

There is also a Hard Disk Upgrade mini-HOWTO
<http://www.storm.ca/~yan/Hard-Disk-Upgrade.html> that gives you a
step by step guide on migrating an entire Linux system, including
LILO, form one hard disk to another.

13.5. Recovery

System crashes come in many and entertaining flavours, and partition
table corruption always guarantees plenty of excitement. A recent and
undoubtedly useful tool for those of us who are happy with the normal
level of excitement, is gpart <http://www.stud.uni-
hannover.de/user/76201/gpart/> which means "Guess PC-Type hard disk
partitions". Useful.

In addition there are some partition utilities
<http://inet.uni2.dk/~svolaf/utilities.htm> available under DOS.

13.6. Rescue Disk

Upgrades of kernel and hardware is not uncommon in the Linux world and
it is therefore important that you prepare an updated rescue disk
especially when you use special drivers to access your hardware.
Rescue disks can be gotten off the net, from your distribution or you
can put one together yourself. Do make sure the boot and root
parameters are set so the kernel will know where to find your system.

If you don't have a recovery floppy you can use the GRUB
<http://www.gnu.org/software/grub/> boot loader to load from a Linux
kernel somewhere on disk, with arguments.

14. Advanced Issues

Linux and related systems offer plenty of possibilities for fast,
efficient and devastating destruction. This document is no exception.
With power comes dangers and the following sections describe a few
more esoteric issues that should not be attempted before reading and
understanding the documentation, the issues and the dangers. You
should also make a backup. Also remember to try to restore the system
from scratch from your backup at least once. Otherwise you might not
be the first to be found with a perfect backup of your system and no
tools available to reinstall it (or, even more embarrassing, some
critical files missing on tape).

The techniques described here are rarely necessary but can be used for
very specific setups. Think very clearly through what you wish to
accomplish before playing around with this.

14.1. Hard Disk Tuning

The hard drive parameters can be tuned using the hdparms utility. Here
the most interesting parameter is probably the read-ahead parameter
which determines how much prefetch should be done in sequential
reading.

If you want to try this out it makes most sense to tune for the
characteristic file size on your drive but remember that this tuning
is for the entire drive which makes it a bit more difficult. Probably
this is only of use on large servers using dedicated news drives etc.

For safety the default hdparm settings are rather conservative. The
disadvantage is that this mean you can get lost interrupts if you have
a high frequency of IRQs as you would when using the serial port and
an IDE disk as IRQs from the latter would mask other IRQs. This would
be noticeable as less then ideal performance when downloading data
from the net to disk. Setting hdparm -u1 device would prevent this
masking and either improve your performance or, depending on hardware,
corrupt the data on your disk. Experiment with caution and fresh
backups.

For more information read the article The Need For Speed
<http://www.linuxforum.com/plug/articles/needforspeed.html> on tuning
with hdparm.

14.2. File System Tuning

Most file systems come with a tuning utility and for ext2fs there is
the tune2fs utility. Several parameters can be modified but perhaps
the most useful parameter here is what size should be reserved and who
should be able to take advantage of this which could help you getting
more useful space out of your drives, possibly at the cost of less
room for repairing a system should it crash.

14.3. Spindle Synchronizing

This should not in itself be dangerous, other than the peculiar fact
that the exact details of the connections remain unclear for many
drives. The theory is simple: keeping a fixed phase difference between
the different drives in a RAID setup makes for less waiting for the
right track to come into position for the read/write head. In practice
it now seems that with large read-ahead buffers in the drives the
effect is negligible.

Spindle synchronisation should not be used on RAID0 or RAID 0/1 as you
would then lose the benefit of having the read heads over different
areas of the mirrored sectors.

15. Troubleshooting

Much can go wrong and this is the start of a growing list of symptoms,
problems and solutions:

15.1. During Installation

15.1.1. Locating Disks

Symptoms
Cannot find disk

Problem
How to find what drive letter corresponds to what disk/partition

Solution
Remember Linux does not use drive letters but device names. More
information can be found in ``Drive names''.

Symptoms
Cannot partition disk

Problem
Most likely wrong input to the command line for fdisk or similar
tool.

Solution
Remember to use /dev/hda rather than just hda. Also do not use
numbers behind hda, those indicate partitions.

15.1.2. Formatting

Symptoms
Cannot format disk.

Problem
Strictly speaking you format partitions not disks.

Solution
Make sure you add the partition number after the device name of
the disk, for instance /dev/hda1 to the command line.

15.2. During Booting

15.2.1. Booting fails

Symptoms
Number keep scrolling up the screen.

Problem
Possibly corrupt disk.

Solution
Try another disk, you might have to reinstall. Check for loose
cables and possible data corruption.

Symptoms
Get LI and then it hangs.

Problem
You use LILO to load Linux but LILO cannot find your root.

Solution
Read the LILO HOWTO.

Symptoms
Kernel panics, something about missing root file system.

Problem
The kernel does not know where the root partition is.

Solution
Use rdev or (if applicable) LILO to add information to the
kernel image where your root is.

15.2.2. Getting into Single User Mode

Symptoms
System boots but get into a root shell in single user mode.

Problem
Something went wrong in the later stages of booting and the
system has come far enough to let you open a shell to repair the
system.

Solution
Locate the problems from the boot log. Note that file system can
be in read-only mode. Remount read-write if you have to. Often
the reason is that the /etc/fstab contained an entry that was
mismapped such as trying to mount a swap partition as your
normal file space.

15.3. During Running

15.3.1. Swap

Symptoms
Short on memory

Problem
Swap space is not available

Solution
Type free and check the output. If you get

total used free shared buffers cached
Mem: 46920 30136 16784 7480 11788 5764
-/+ buffers/cache: 12584 34336
Swap: 128484 9176 119308

then system is running normal. If the line with Swap: contains
zeros you have either not mounted the swap space (partition or swap
file) (see swapon(8)) or not formatted the swap space (see
mkswap(8)).

15.3.2. Partitions

Symptoms
No room amidst plenty 1

Problem
Partitionitis:Underdimensioned partition sizes has caused
overflow in some areas

Solution
Examine your partition usage using df(1) and locate problem
areas. Normally the problem can be solved by removing old junk
but you might have to repartition your system, see section
``Repartitioning''.

Symptoms
No room amidst plenty 2

Problem
Running out of i-nodes has caused overflow in some ares, often
in areas with many small files such as news spool.

Solution
Examine your partition usage using df -i and locate problem
areas. Normally the problem is solved by reformatting using a
higher number of i-nodes, see mkfs(8) and related man pages.

16. Further Information

There is wealth of information one should go through when setting up a
major system, for instance for a news or general Internet service
provider. The FAQs in the following groups are useful:

16.1. News groups

Some of the most interesting news groups are:

· Storage <news:comp.arch.storage>.

· PC storage <news:comp.sys.ibm.pc.hardware.storage>.

· AFS <news:alt.filesystems.afs>.

· SCSI <news:comp.periphs.scsi>.

· Linux setup <news:comp.os.linux.setup>.

Most newsgroups have their own FAQ that are designed to answer most of
your questions, as the name Frequently Asked Questions indicate. Fresh
versions should be posted regularly to the relevant newsgroups. If you
cannot find it in your news spool you could go directly to the FAQ
main archive FTP site <ftp://rtfm.mit.edu>. The WWW versions can be
browsed at FAQ main archive WWW site <http://www.faqs.org/faqs/FAQ-
List.html>.

Some FAQs have their own home site, of particular interest here are

· SCSI FAQ <http://www.scsifaq.org/> and

· comp.arch.storage FAQ <http://alumni.caltech.edu/~rdv/comp-arch-
storage/FAQ-1.html>.

16.2. Mailing Lists

These are low noise channels mainly for developers. Think twice before
asking questions there as noise delays the development. Some relevant
lists are linux-raid, linux-scsi and linux-ext2fs. Many of the most
useful mailing lists run on the vger.rutgers.edu server but this is
notoriously overloaded, so try to find a mirror. There are some lists
mirrored at The Redhat Home Page <http://www.redhat.com>. Many lists
are also accessible at linuxhq <http://www.linuxhq.com/lnxlists/>, and
the rest of the web site is a gold mine of useful information.

If you want to find out more about the lists available you can send a
message with the line lists to the list server at vger.rutgers.edu (
majordomo@vger.rutgers.edu). If you need help on how to use the mail
server just send the line help to the same address. Due to the
popularity of this server it is likely it takes a bit to time before
you get a reply or even get messages after you send a subscribe
command.

There is also a number of other majordomo list servers that can be of
interest such as the EATA driver list ( linux-eata@mail.uni-mainz.de)
and the Intelligent IO list linux-i2o@dpt.com.

Mailing lists are in a state of flux but you can find links to a
number of interesting lists from the Linux Documentation Homepage
<http://www.linuxdoc.org/>.

16.3. HOWTO

These are intended as the primary starting points to get the
background information as well as show you how to solve a specific
problem. Some relevant HOWTOs are Bootdisk, Installation, SCSI and
UMSDOS. The main site for these is the LDP archive
<http://www.linuxdoc.org/>.

There is a a new HOWTO out that deals with setting up a DPT RAID
system, check out the DPT RAID HOWTO homepage
<http://www.ram.org/computing/linux/dpt_raid.html>.

16.4. Mini-HOWTO

These are the smaller free text relatives to the HOWTOs. Some
relevant mini-HOWTOs are Backup-With-MSDOS, Diskless, LILO, Large
Disk, Linux+DOS+Win95+OS2, Linux+OS2+DOS, Linux+Win95, NFS-Root,
Win95+Win+Linux, ZIP Drive . You can find these at the same place as
the HOWTOs, usually in a sub directory called mini. Note that these
are scheduled to be converted into SGML and become proper HOWTOs in
the near future.

The old Linux Large IDE mini-HOWTO is no longer valid, instead read
/usr/src/linux/drivers/block/README.ide or
/usr/src/linux/Documentation/ide.txt.

16.5. Local Resources

In most distributions of Linux there is a document directory
installed, have a look in the /usr/doc directory. where most packages
store their main documentation and README files etc. Also you will
here find the HOWTO archive ( /usr/doc/HOWTO) of ready formatted
HOWTOs and also the mini-HOWTO archive ( /usr/doc/HOWTO/mini
<file:///usr/doc/HOWTO/mini>) of plain text documents.

Many of the configuration files mentioned earlier can be found in the
/etc directory. In particular you will want to work with the
/etc/fstab file that sets up the mounting of partitions and possibly
also /etc/mdtab file that is used for the md system to set up RAID.

The kernel source in /usr/src/linux <file:///usr/src/linux> is, of
course, the ultimate documentation. In other words, use the source,
Luke. It should also be pointed out that the kernel comes not only
with source code which is even commented (well, partially at least)
but also an informative documentation directory
<file:///usr/src/linux/Documentation>. If you are about to ask any
questions about the kernel you should read this first, it will save
you and many others a lot of time and possibly embarrassment.

Also have a look in your system log file ( /var/log/messages) to see
what is going on and in particular how the booting went if too much
scrolled off your screen. Using tail -f /var/log/messages in a
separate window or screen will give you a continuous update of what is
going on in your system.

You can also take advantage of the /proc file system that is a window
into the inner workings of your system. Use cat rather than more to
view the files as they are reported as being zero length. Reports are
that less works well here.

16.6. Web Pages

There is a huge number of informative web pages out there and by their
very nature they change quickly so don't be too surprised if these
links become quickly outdated.

A good starting point is of course the Linux Documentation Homepage
<http://www.linuxdoc.org/>. that is a information central for
documentation, project pages and much, much more.

· Mike Neuffer, the author of the DPT caching RAID controller
drivers, has some interesting pages on SCSI <http://www.uni-
mainz.de/~neuffer/scsi/> and DPT <http://www.uni-
mainz.de/~neuffer/scsi/dpt/>.

· Software RAID development information can be found at Linux Kernel
site <http://www.kernel.org/> along with patches and utilities.

· Disk related information on benchmarking, RAID, reliability and
much, much more can be found at Linas Vepstas <http://linas.org>
project page.

· There is also information available on how to RAID the root
partition <ftp://ftp.bizsystems.com/pub/raid/Root-RAID-HOWTO.html>
and what software packages are needed to achieve this.

· In depth documentation on ext2fs
<http://step.polymtl.ca/~ldd/ext2fs/ext2fs_toc.html> is also
available.

· People who looking for information on VFAT, FAT32 and Joliet could
have a look at the development page
<http://bmrc.berkeley.edu/people/chaffee/index.html>. These
drivers are in the 2.1.x kernel development series as well as in
2.0.34 and later.

For diagrams and information on all sorts of disk drives, controllers
etc. both for current and discontinued lines The Ref
<http://theref.aquascape.com/theref.html> is the site you need. There
is a lot of useful information here, a real treasure trove.

Please let me know if you have any other leads that can be of
interest.

16.7. Search Engines

When all fails try the internet search engines. There is a huge number
of them, all a little different from each other. It falls outside the
scope of this HOWTO to describe how best to use them. Instead you
could turn to the Troubleshooting on the Internet mini-HOWTO, and the
Updated mini-HOWTO.

If you have to ask for help you are most likely to get help in the
Linux Setup <news:comp.os.linux.setup> news group. Due to large
workload and a slow network connection I am not able to follow that
newsgroup so if you want to contact me you have to do so by e-mail.
17. Getting Help

In the end you might find yourself unable to solve your problems and
need help from someone else. The most efficient way is either to ask
someone local or in your nearest Linux user group, search the web for
the nearest one.

Another possibility is to ask on Usenet News in one of the many, many
newsgroups available. The problem is that these have such a high
volume and noise (called low signal-to-noise ratio) that your question
can easily fall through unanswered.

No matter where you ask it is important to ask well or you will not be
taken seriously. Saying just my disk does not work is not going to
help you and instead the noise level is increased even further and if
you are lucky someone will ask you to clarify.

Instead describe your problems in some detail that will enable people
to help you. The problem could lie somewhere you did not expect.
Therefore you are advised to list up the following information on your
system:

Hardware

· Processor

· DMA

· IRQ

· Chip set (LX, BX etc)

· Bus (ISA, VESA, PCI etc)

· Expansion cards used (Disk controllers, video, IO etc)

Software

· BIOS (On motherboard and possibly SCSI host adapters)

· LILO, if used

· Linux kernel version as well as possible modifications and
patches

· Kernel parameters, if any

· Software that shows the error (with version number or date)

Peripherals

· Type of disk drives with manufacturer name, version and type

· Other relevant peripherals connected to the same busses

As an example of how interrelated these problems are: an old chip set
caused problems with a certain combination of video controller and
SCSI host adapter.

Remember that booting text is logged to /var/log/messages which can
answer most of the questions above. Obviously if the drives fail you
might not be able to get the log saved to disk but you can at least
scroll back up the screen using the SHIFT and PAGE UP keys. It may
also be useful to include part of this in your request for help but do
not go overboard, keep it brief as a complete log file dumped to
Usenet News is more than a little annoying.

18. Concluding Remarks

Disk tuning and partition decisions are difficult to make, and there
are no hard rules here. Nevertheless it is a good idea to work more on
this as the payoffs can be considerable. Maximizing usage on one drive
only while the others are idle is unlikely to be optimal, watch the
drive light, they are not there just for decoration. For a properly
set up system the lights should look like Christmas in a disco. Linux
offers software RAID but also support for some hardware base SCSI RAID
controllers. Check what is available. As your system and experiences
evolve you are likely to repartition and you might look on this
document again. Additions are always welcome.

Finally I'd like to sum up my recommendations:

· Disks are cheap but the data they contain could be much more
valuable, use and test your backup system.

· Work is also expensive, make sure you get large enough disks as
refitting new or repartitioning old disks takes time.

· Think reliability, replace old disks before they fail.

· Keep a paper copy of your setup, having it all on disk when the
machine is down will not help you much.

· Start out with a simple design with a minimum of fancy technology
and rather fit it in later. In general adding is easier than
replacing, be it disks, technology or other features.

18.1. Coming Soon

There are a few more important things that are about to appear here.
In particular I will add more example tables as I am about to set up
two fairly large and general systems, one at work and one at home.
These should give some general feeling on how a system can be set up
for either of these two purposes. Examples of smooth running existing
systems are also welcome.

There is also a fair bit of work left to do on the various kinds of
file systems and utilities.

There will be a big addition on drive technologies coming soon as well
as a more in depth description on using fdisk, cfdisk and sfdisk. The
file systems will be beefed up as more features become available as
well as more on RAID and what directories can benefit from what RAID
level.

There is some minor overlapping with the Linux Filesystem Structure
Standard and FHS that I hope to integrate better soon, which will
probably mean a big reworking of all the tables at the end of this
document.

As more people start reading this I should get some more comments and
feedback. I am also thinking of making a program that can automate a
fair bit of this decision making process and although it is unlikely
to be optimum it should provide a simpler, more complete starting
point.

18.2. Request for Information

It has taken a fair bit of time to write this document and although
most pieces are beginning to come together there are still some
information needed before we are out of the beta stage.

· More information on swap sizing policies is needed as well as
information on the largest swap size possible under the various
kernel versions.

· How common is drive or file system corruption? So far I have only
heard of problems caused by flaky hardware.

· References to speed and drives is needed.

· Are any other Linux compatible RAID controllers available?

· What relevant monitoring, management and maintenance tools are
available?

· General references to information sources are needed, perhaps this
should be a separate document?

· Usage of /tmp and /var/tmp has been hard to determine, in fact what
programs use which directory is not well defined and more
information here is required. Still, it seems at least clear that
these should reside on different physical drives in order to
increase paralellicity.

18.3. Suggested Project Work

Now and then people post on comp.os.linux.*, looking for good project
ideas. Here I will list a few that comes to mind that are relevant to
this document. Plans about big projects such as new file systems
should still be posted in order to either find co-workers or see if
someone is already working on it.

Planning tools
that can automate the design process outlines earlier would
probably make a medium sized project, perhaps as an exercise in
constraint based programming.

Partitioning tools
that take the output of the previously mentioned program and
format drives in parallel and apply the appropriate symbolic
links to the directory structure. It would probably be best if
this were integrated in existing system installation software.
The drive partitioning setup used in Solaris is an example of
what it can look like.

Surveillance tools
that keep an eye on the partition sizes and warn before a
partition overflows.

Migration tools
that safely lets you move old structures to new (for instance
RAID) systems. This could probably be done as a shell script
controlling a back up program and would be rather simple. Still,
be sure it is safe and that the changes can be undone.

19. Questions and Answers

This is just a collection of what I believe are the most common
questions people might have. Give me more feedback and I will turn
this section into a proper FAQ.

· Q:How many physical disk drives (spindles) does a Linux system
need?

A: Linux can run just fine on one drive (spindle). Having enough
RAM (around 32 MB, and up to 64 MB) to support swapping is a better
price/performance choice than getting a second disk. (E)IDE disk
is usually cheaper (but a little slower) than SCSI.

· Q: I have a single drive, will this HOWTO help me?

A: Yes, although only to a minor degree. Still, section ``Physical
Track Positioning'' will offer you some gains.

· Q: Are there any disadvantages in this scheme?

A: There is only a minor snag: if even a single partition overflows
the system might stop working properly. The severity depends of
course on what partition is affected. Still this is not hard to
monitor, the command df gives you a good overview of the situation.
Also check the swap partition(s) using free to make sure you are
not about to run out of virtual memory.

· Q: OK, so should I split the system into as many partitions as
possible for a single drive?

A: No, there are several disadvantages to that. First of all
maintenance becomes needlessly complex and you gain very little in
this. In fact if your partitions are too big you will seek across
larger areas than needed. This is a balance and dependent on the
number of physical drives you have.

· Q: Does that mean more drives allows more partitions?

A: To some degree, yes. Still, some directories should not be split
off from root, check out the file system standards for more
details.

· Q: What if I have many drives I want to use?

A: If you have more than 3-4 drives you should consider using RAID
of some form. Still, it is a good idea to keep your root partition
on a simple partition without RAID, see section ``RAID'' for more
details.

· Q: I have installed the latest Windows95 but cannot access this
partition from within the Linux system, what is wrong?

A: Most likely you are using FAT32 in your windows partition. It
seems that Microsoft decided we needed yet another format, and this
was introduced in their latest version of Windows95, called OSR2.
The advantage is that this format is better suited to large drives.

You might also be interested to hear that Microsoft NT 4.0 does not
support it yet either.

· Q: I cannot get the disk size and partition sizes to match,
something is missing. What has happened?

A:It is possible you have mounted a partition onto a mount point
that was not an empty directory. Mount points are directories and
if it is not empty the mounting will mask the contents. If you do
the sums you will see the amount of disk space used in this
directory is missing from the observed total.

To solve this you can boot from a rescue disk and see what is
hiding behind your mount points and remove or transfer the contents
by mounting the offending partition on a temporary mounting point.
You might find it useful to have "spare" emergency mounting points
ready made.

· Q: It doesn't look like my swap partition is in use, how come?

A: It is possible that it has not been necessary to swap out,
especially if you have plenty of RAM. Check your log files to see
if you ran out of memory at one point or another, in that case your
swap space should have been put to use. If not it is possible that
either the swap partition was not assigned the right number, that
you did not prepare it with mkswap or that you have not done swapon
or added it to your /etc/fstab file.

· Q: What is this Nyx that is mentioned several times here?

A: It is a large free Unix system with currently about 10000 users.
I use it for my web pages for this HOWTO as well as a source of
ideas for a setup of large Unix systems. It has been running for
many years and has a quite stable setup. For more information you
can view the Nyx homepage <http://www.nyx.net> which also gives you
information on how to get your own free account.

20. Bits and Pieces

This is basically a section where I stuff all the bits I have not yet
decided where should go, yet that I feel is worth knowing about. It is
a kind of transient area.

20.1. Swap Partition: to Use or Not to Use

In many cases you do not need a swap partition, for instance if you
have plenty of RAM, say, more than 64 MB, and you are the sole user of
the machine. In this case you can experiment running without a swap
partition and check the system logs to see if you ran out of virtual
memory at any point.

Removing swap partitions have two advantages:

· you save disk space (rather obvious really)

· you save seek time as swap partitions otherwise would lie in the
middle of your disk space.

In the end, having a swap partition is like having a heated toilet:
you do not use it very often, but you sure appreciate it when you
require it.

20.2. Mount Point and /mnt

In an earlier version of this document I proposed to put all
permanently mounted partitions under /mnt. That, however, is not such
a good idea as this itself can be used as a mount point, which leads
to all mounted partitions becoming unavailable. Instead I will propose
mounting straight from root using a meaningful name like
/mnt.descriptive-name.

Lately I have become aware that some Linux distributions use mount
points at subdirectories under /mnt, such as /mnt/floppy and
/mnt/cdrom, which just shows how confused the whole issue is.
Hopefully FHS should clarify this.

20.3. Power and Heating

Not many years ago a machine with the equivalent power of a modern PC
required 3-phase power and cooling, usually by air conditioning the
machine room, some times also by water cooling. Technology has
progressed very quickly giving not only high speed but also low power
components. Still, there is a definite limit to the technology,
something one should keep in mind as the system is expanded with yet
another disk drive or PCI card. When the power supply is running at
full rated power, keep in mind that all this energy is going
somewhere, mostly into heat. Unless this is dissipated using fans you
will get a serious heating inside the cabinet followed by a reduced
reliability and also life time of the electronics. Manufacturers
state minimum cooling requirements for their drives, usually in terms
of cubic feet per minute (CFM). You are well advised to take this
serious.

Keep air flow passages open, clean out dust and check the temperature
of your system running. If it is too hot to touch it is probably
running too hot.

If possible use sequential spin up for the drives. It is during spin
up, when the drive platters accelerate up to normal speed, that a
drive consumes maximum power and if all drives start up simultaneously
you could go beyond the rated power maximum of your power supply.

20.4. Deja

This is an Internet system that no doubt most of you are familiar
with. It searches and serves Usenet News articles from 1995 and to
the latest postings and also offers a web based reading and posting
interface. There is a lot more, check out Deja <http://www.deja.com>
for more information. It changed name from Dejanews.
What perhaps is less known, is that they use about 120 Linux SMP
computers many of which use the md module to manage between 4 and 24
Gig of disk space (over 1200 Gig altogether) for this service. The
system is continuously growing but at the time of writing they use
mostly dual Pentium Pro 200MHz and Pentium II 300 MHz systems with 256
MB RAM or more.

A production database machine normally has 1 disk for the operating
system and between 4 and 6 disks managed by the md module where the
articles are archived. The drives are connected to BusLogic Model
BT-946C and BT-958 PCI SCSI adapters, usually one to a machine.

For the production systems (which are up 365 days a year) the downtime
attributable to disk errors is less than 0.25 % (that is a quarter of
1%, not 25%).

Just in case: this is not an advertisement, it is stated as an example
of how much is required for what is a major Internet service.

20.5. Crash Recovery

Occationally hard disks crash. A crash causing data scrambling can
often be at least partially recovered from and there are already
HOWTOs describing this.

In case of hardware failure things are far more serious, and you have
two options: either send the drive to a professional data recovery
company, or try recovering yourself. The latter is of course high risk
and can cause more damage.

If a disk stops rotating or fails to spin up, the number one advice is
first to turn off the system as fast as safely possible.

Next you could try disconnecting the drives and power up the machine,
just to check power with a multimeter that power is present. Quite
often connectors can get unseated and cause all sorts of problems.

If you decide to risk trying it yourself you could check all
connectors and then reapply power and see if the drive spins up and
responds. If it still is dead turn off power quickly, preferrably
before the operating system boots. Make sure that delayed spinup is
not deceiving you here.

If you decide to progress even further (and take higher risks) you
could remove the drive, give it a firm tap on the side so that the
disk moves a little with respect to the casing. This can help in
unsticking the head from the surface, allowing the platter to move
freely as the motor power is not sufficient to unstick a stuck head on
its own.

Also if a drive has been turned off for a while after running for long
periods of time, or if it has overheated, the lubricant can harden of
drain out of the bearings. In this case warming the drive slowly and
gently up to normal operating temperature will possibly recover the
lubrication problems.

If after this the drive still does not respond the last possible and
the highest risk suggestion is to replace the circuit board of the
drive with a board from am identical model drive.

Often the contents of a drive is worth far more than the media itself,
so do consider professional help. These companies have advanced
equipment and know-how obtained from the manufacturers on how to
recover a damaged drive, far beyond that of a hobbyist.

21. Appendix A: Partitioning Layout Table: Mounting and Linking

The following table is designed to make layout a simpler paper and
pencil exercise. It is probably best to print it out (using NON
PROPORTIONAL fonts) and adjust the numbers until you are happy with
them.

Mount point is what directory you wish to mount a partition on or the
actual device. This is also a good place to note how you plan to use
symbolic links.

The size given corresponds to a fairly big Debian 1.2.6 installation.
Other examples are coming later.

Mainly you use this table to select what structure and drives you will
use, the partition numbers and letters will come from the next two
tables.

Directory Mount point speed seek transfer size SIZE

swap __________ ooooo ooooo ooooo 32 ____

/ __________ o o o 20 ____

/tmp __________ oooo oooo oooo ____

/var __________ oo oo oo 25 ____
/var/tmp __________ oooo oooo oooo ____
/var/spool __________ ____
/var/spool/mail __________ o o o ____
/var/spool/news __________ ooo ooo oo ____
/var/spool/____ __________ ____ ____ ____ ____

/home __________ oo oo oo ____

/usr __________ 500 ____
/usr/bin __________ o oo o 250 ____
/usr/lib __________ oo oo ooo 200 ____
/usr/local __________ ____
/usr/local/bin __________ o oo o ____
/usr/local/lib __________ oo oo ooo ____
/usr/local/____ __________ ____
/usr/src __________ o oo o 50 ____

DOS __________ o o o ____
Win __________ oo oo oo ____
NT __________ ooo ooo ooo ____

/mnt._________ __________ ____ ____ ____ ____
/mnt._________ __________ ____ ____ ____ ____
/mnt._________ __________ ____ ____ ____ ____
/_____________ __________ ____ ____ ____ ____
/_____________ __________ ____ ____ ____ ____
/_____________ __________ ____ ____ ____ ____

Total capacity:

22. Appendix B: Partitioning Layout Table: Numbering and Sizing

This table follows the same logical structure as the table above where
you decided what disk to use. Here you select the physical tracking,
keeping in mind the effect of track positioning mentioned earlier in
``Physical Track Positioning''.

The final partition number will come out of the table after this.

Drive sda sdb sdc hda hdb hdc ___

SCSI ID | __ | __ | __ |

/ | | | | | | |

/tmp | | | | | | |

DOS | | | | | | |
Win : : : : : : :
NT | | | | | | |

/mnt.___/_____ | | | | | | |
/mnt.___/_____ : : : : : : :
/mnt.___/_____ | | | | | | |
/_____________ : : : : : : :
/_____________ | | | | | | |
/_____________ : : : : : : :

Total capacity:

23. Appendix C: Partitioning Layout Table: Partition Placement

This is just to sort the partition numbers in ascending order ready to
input to fdisk or cfdisk. Here you take physical track positioning
into account when finalizing your design. Unless you get specific
information otherwise, you can assume track 0 is the outermost track.

These numbers and letters are then used to update the previous tables,
all of which you will find very useful in later maintenance.

In case of disk crash you might find it handy to know what SCSI id
belongs to which drive, consider keeping a paper copy of this.

Drive : sda sdb sdc hda hdb hdc ___

Total capacity: | ___ | ___ | ___ | ___ | ___ | ___ | ___
SCSI ID | __ | __ | __ |

Partition

1 | | | | | | |
2 : : : : : : :
3 | | | | | | |
4 : : : : : : :
5 | | | | | | |
6 : : : : : : :
7 | | | | | | |
8 : : : : : : :
9 | | | | | | |
10 : : : : : : :
11 | | | | | | |
12 : : : : : : :
13 | | | | | | |
14 : : : : : : :
15 | | | | | | |
16 : : : : : : :

24. Appendix D: Example: Multipurpose Server

The following table is from the setup of a medium sized multipurpose
server where I once worked. Aside from being a general Linux machine
it will also be a network related server (DNS, mail, FTP, news,
printers etc.) X server for various CAD programs, CD ROM burner and
many other things. The files reside on 3 SCSI drives with a capacity
of 600, 1000 and 1300 MB.

Some further speed could possibly be gained by splitting /usr/local
from the rest of the /usr system but we deemed the further added
complexity would not be worth it. With another couple of drives this
could be more worthwhile. In this setup drive sda is old and slow and
could just a well be replaced by an IDE drive. The other two drives
are both rather fast. Basically we split most of the load between
these two. To reduce dangers of imbalance in partition sizing we have
decided to keep /usr/bin and /usr/local/bin in one drive and /usr/lib
and /usr/local/lib on another separate drive which also affords us
some drive parallelizing.

Even more could be gained by using RAID but we felt that as a server
we needed more reliability than was then afforded by the md patch and
a dedicated RAID controller was out of our reach.

25. Appendix E: Example: Mounting and Linking

Directory Mount point speed seek transfer size SIZE

swap sdb2, sdc2 ooooo ooooo ooooo 32 2x64

/ sda2 o o o 20 100

/tmp sdb3 oooo oooo oooo 300

/var __________ oo oo oo ____
/var/tmp sdc3 oooo oooo oooo 300
/var/spool sdb1 436
/var/spool/mail __________ o o o ____
/var/spool/news __________ ooo ooo oo ____
/var/spool/____ __________ ____ ____ ____ ____

/home sda3 oo oo oo 400

/usr sdb4 230 200
/usr/bin __________ o oo o 30 ____
/usr/lib -> libdisk oo oo ooo 70 ____
/usr/local __________ ____
/usr/local/bin __________ o oo o ____
/usr/local/lib -> libdisk oo oo ooo ____
/usr/local/____ __________ ____
/usr/src ->/home/usr.src o oo o 10 ____

DOS sda1 o o o 100
Win __________ oo oo oo ____
NT __________ ooo ooo ooo ____

/mnt.libdisk sdc4 oo oo ooo 226
/mnt.cd sdc1 o o oo 710

Total capacity: 2900 MB

26. Appendix F: Example: Numbering and Sizing

Here we do the adjustment of sizes and positioning.

Directory sda sdb sdc

swap | | 64 | 64 |

/ | 100 | | |

/tmp | | 300 | |

/home | 400 | | |

DOS | 100 | | |
Win : : : :
NT | | | |

Total capacity: | 600 | 1000 | 1300 |

27. Appendix G: Example: Partition Placement

This is just to sort the partition numbers in ascending order ready to
input to fdisk or cfdisk. Remember to optimize for physical track
positioning (not done here).

Drive : sda sdb sdc

Total capacity: | 600 | 1000 | 1300 |

Partition

1 | 100 | 436 | 710 |
2 : 100 : 64 : 64 :
3 | 400 | 300 | 300 |
4 : : 200 : 226 :

28. Appendix H: Example II

The following is an example of a server setup in an academic setting,
and is contributed by nakano (at) apm.seikei.ac.jp. I have only done
minor editing to this section.

/var/spool/delegate is a directory for storing logs and cache files of
an WWW proxy server program, "delegated". Since I don't notice it
widely, there are 1000--1500 requests/day currently, and average disk
usage is 15--30% with expiration of caches each day.

/mnt.archive is used for data files which are big and not frequently
referenced such a s experimental data (especially graphic ones),
various source archives, and Win95 backups (growing very fast...).

/mnt.root is backup root file system containing rescue utilities. A
boot floppy is also prepared to boot with this partition.

=================================================
Directory sda sdb hda

swap | 64 | 64 | |
/ | | | 20 |
/tmp | | | 180 |

/var : 300 : : :
/var/tmp | | 300 | |
/var/spool/delegate | 300 | | |

/home | | | 850 |
/usr | 360 | | |
/usr/lib -> /mnt.lib/usr.lib
/usr/local/lib -> /mnt.lib/usr.local.lib

/mnt.lib | | 350 | |
/mnt.archive : : 1300 : :
/mnt.root | | 20 | |

Total capacity: 1024 2034 1050

=================================================
Drive : sda sdb hda
Total capacity: | 1024 | 2034 | 1050 |

Partition
1 | 300 | 20 | 20 |
2 : 64 : 1300 : 180 :
3 | 300 | 64 | 850 |
4 : 360 : ext : :
5 | | 300 | |
6 : : 350 : :

Filesystem 1024-blocks Used Available Capacity Mounted on
/dev/hda1 19485 10534 7945 57% /
/dev/hda2 178598 13 169362 0% /tmp
/dev/hda3 826640 440814 343138 56% /home
/dev/sda1 306088 33580 256700 12% /var
/dev/sda3 297925 47730 234807 17% /var/spool/delegate
/dev/sda4 363272 170872 173640 50% /usr
/dev/sdb5 297598 2 282228 0% /var/tmp
/dev/sdb2 1339248 302564 967520 24% /mnt.archive
/dev/sdb6 323716 78792 228208 26% /mnt.lib

Apparently /tmp and /var/tmp is too big. These directories shall be
packed together into one partition when disk space shortage comes.

/mnt.lib is also seemed to be, but I plan to install newer TeX and
ghostscript archives, so /usr/local/lib may grow about 100 MB or so
(since we must use Japanese fonts!).

Whole system is backed up by Seagate Tapestore 8000 (Travan TR-4,
4G/8G).

29. Appendix I: Example III: SPARC Solaris

The following section is the basic design used at work for a number of
Sun SPARC servers running Solaris 2.5.1 in an industrial development
environment. It serves a number of database and cad applications in
addition to the normal services such as mail.

Simplicity is emphasized here so /usr/lib has not been split off from
/usr.

This is the basic layout, planned for about 100 users.

Drive: SCSI 0 SCSI 1

Partition Size (MB) Mount point Size (MB) Mount point

0 160 swap 160 swap
1 100 /tmp 100 /var/tmp
2 400 /usr
3 100 /
4 50 /var
5
6 remainder /local0 remainder /local1

Due to specific requirements at this place it is at times necessary to
have large partitions available on a short notice. Therefore drive 0
is given as many tasks as feasible, leaving a large /local1 partition.

This setup has been in use for some time now and found satisfactorily.

For a more general and balanced system it would be better to swap /tmp
and /var/tmp and then move /var to drive 1.

30. Appendix J: Example IV: Server with 4 Drives

This gives an example of using all techniques described earlier, short
of RAID. It is admittedly rather complicated but offers in return high
performance from modest hardware. Dimensioning are skipped but
reasonable figures can be found in previous examples.

Partition sda sdb sdc sdd
---- ---- ---- ----
1 root overview lib news
2 swap swap swap swap
3 home /usr /var/tmp /tmp
4 spare root mail /var

Setup is optimised with respect to track positioning but also for
minimising drive seeks.

If you want DOS or Windows too you will have to use sda1 for this and
move the other partitions after that. It will be advantageous to use
the swap partitions on sdb2, sdc2 and sdd2 for Windows swap, TEMPDIR
and Windows temporary directory under these sessions. A number of
other HOWTOs describe how you can make several operating systems
coexist on your machine.

For completeness a 4 drive example using several types of RAID is also
given which is even more complex than the example above.

Partition sda sdb sdc sdd
---- ---- ---- ----
1 boot overview news news
2 overview swap swap swap
3 swap lib lib lib
4 lib overview /tmp /tmp
5 /var/tmp /var/tmp mail /usr
6 /home /usr /usr mail
7 /usr /home /var
8 / (root) spare root

Here all duplicates are parts of a RAID 0 set with two exceptions,
swap which is interleaved and home and mail which are implemented as
RAID 1 for safety.

Note that boot and root are separated: only the boot file with the
kernel has to reside within the 1023 cylinder limit. The rest of the
root files can be anywhere and here they are placed on the slowest
outermost partition. For simplicity and safety the root partition is
not on a RAID system.

With such a complicated comes an equally complicated fstab file. The
large number of partitions makes it important to do the fsck passes in
the right order, otherwise the process can take perhaps ten times as
long time to complete as the optimal solution.

/dev/sda8 / ? ? 1 1 (a)
/dev/sdb8 / ? noauto 1 2 (b)
/dev/sda1 boot ? ? 1 2 (a)
/dev/sdc7 /var ? ? 1 2 (c)
/dev/md1 news ? ? 1 3 (c+d)
/dev/md2 /var/tmp ? ? 1 3 (a+b)
/dev/md3 mail ? ? 1 4 (c+d)
/dev/md4 /home ? ? 1 4 (a+b)
/dev/md5 /tmp ? ? 1 5 (c+d)
/dev/md6 /usr ? ? 1 6 (a+b+c+d)
/dev/md7 /lib ? ? 1 7 (a+b+c+d)

The letters in the brackets indicate what drives will be active for
each fsck entry and pass. These letters are not present in a real
fstab file. All in all there are 7 passes.

31. Appendix K: Example V: Dual Drive System

A dual drive system offers less opportunity for clever schemes but the
following should provide a simple starting point.
Partition sda sdb
---- ----
1 boot lib
2 swap news
3 /tmp swap
4 /usr /var/tmp
5 /var /home
6 / (root)

If you use a dual OS system you have to keep in mind that many other
systems must boot from the first partition on the first drive. A
simple DOS / Linux system could look like this:

Partition sda sdb
---- ----
1 DOS lib
2 boot news
3 swap swap
4 /tmp /var/tmp
5 /usr /home
6 /var DOSTEMP
7 / (root)

Also remember that DOS and Windows prefer there to be just a single
primary partition which has to be the first one where it boots from.
As Linux can happily exist in logical partitions this is not a big
problem.

32. Appendix L: Example VI: Single Drive System

Although this falls somewhat outside the scope of this HOWTO it cannot
be denied that recently some rather large drives have become very
affordable. Drives with 10 - 20 GB are becoming common and the
question often is how best to partition such monsters. Interestingly
enough very few seem to have any problems in filling up such drives
and the future looks generally quite rosy for manufacturers planning
on even bigger drives.

Opportunities for optimisations are of course even smaller than for 2
drive systems but some tricks can still be used to optimise track
positions while minimising head movements.

Partition hda Size estimate (MB)
---- ------------------
1 DOS 500
2 boot 20
3 Winswap 200
4 data The bulk of the drive
5 lib 50 - 500
6 news 300+
7 swap 128 (Maximum size for 32-bit CPU)
8 tmp 300+ (/tmp and /var/tmp)
9 /usr 50 - 500
10 /home 300+
11 /var 50 - 300
12 mail 300+
13 / (root) 30
14 dosdata 10 ( Windows bug workaround!)

Remember that the dosdata partition is a DOS filesystem that must be
the very last partition on the drive, otherwise Windows gets confused.

33. Appendix M: Disk System Documenter

This shell script was very kindly provided by Steffen Hulegaard. Run
it as root (superuser) and it will generate a summary of your disk
setup. Run it after you have implemented your design and compare it
with what you designed to check for mistakes. Should your system
develop defects this document will also be a useful starting point for
recovery.

______________________________________________________________________

#!/bin/bash
#$Header: /cvsroot/LDP/howto/linuxdoc/Multi-Disk-HOWTO.sgml,v 1.5 2002/05/20 21:12:29 gferg Exp $
#
# makediskdoc Collects storage/disk info via df, mount,
# /etc/fstab and fdisk. Creates a single
# reference file -- /root/sysop/doc/README.diskdoc
# Especially good for documenting storage
# config/partioning
#
# 11/11/1999 SC Hulegaard Created just before RedHat 5.2 to
# RedHat 6.1 upgrade
# 12/31/1999 SC Hulegaard Added sfdisk -glx usage just prior to
# collapse of my Quantum Grand Prix (4.3 Gb)
#
# SEE ALSO Other /root/bin/make*doc commands to produce other /root/sysop/doc/README.*
# files. For example, /root/bin/makenetdoc.
#
FILE=/root/sysop/doc/README.diskdoc
echo Creating $FILE ...
echo ' ' > $FILE
echo $FILE >> $FILE
echo Produced By $0 >> $FILE
echo `date` >> $FILE
echo ' ' >> $FILE
echo $Header: /cvsroot/LDP/howto/linuxdoc/Multi-Disk-HOWTO.sgml,v 1.5 2002/05/20 21:12:29 gferg Exp $ >> $FILE
echo ' ' >> $FILE
echo DESCRIPTION: df -a >> $FILE
df -a >> $FILE 2>&1
echo ' ' >> $FILE
echo DESCRIPTION: df -ia >> $FILE
df -ia >> $FILE 2>&1
echo ' ' >> $FILE
echo DESCRIPTION: mount >> $FILE
mount >> $FILE 2>&1
echo ' ' >> $FILE
echo DESCRIPTION: /etc/fstab >> $FILE
cat /etc/fstab >> $FILE
echo ' ' >> $FILE
echo DESCRIPTION: sfdisk -s disk device size summary >> $FILE
sfdisk -s >> $FILE
echo ' ' >> $FILE
echo DESCRIPTION: sfdisk -glx info for all disks listed in /etc/fstab >> $FILE
for x in `cat /etc/fstab | egrep /dev/[sh] | cut -c 0-8 | uniq`; do
echo ' ' >> $FILE
echo $x ============================= >> $FILE
sfdisk -glx $x >> $FILE
done
echo ' ' >> $FILE
echo DESCRIPTION: fdisk -l info for all disks listed in /etc/fstab >> $FILE
for x in `cat /etc/fstab | egrep /dev/[sh] | cut -c 0-8 | uniq`; do
echo ' ' >> $FILE
echo $x ============================= >> $FILE
fdisk -l $x >> $FILE
done
echo ' ' >> $FILE
echo DESCRIPTION: dmesg info on both sd and hd drives >> $FILE
dmesg | egrep [hs]d[a-z] >> $FILE
echo '' >> $FILE
echo Done >> $FILE
echo Done
exit

______________________________________________________________________