Modem-HOWTO
David S.Lawyer
<mailto:dave@lafn.org>
v0.38, June 2005
Help with selecting, connecting, configuring, trouble-shooting, and
understanding analog modems for a PC.
______________________________________________________________________
Table of Contents
1. Introduction
1.1 DSL, Cable, and ISDN Modems in other HOWTOs
1.2 Also not well covered: PCMCIA Modems, PPP
1.3 Copyright, Disclaimer, Trademarks, & Credits
1.3.1 Copyright
1.3.2 Disclaimer
1.3.3 Trademarks.
1.3.4 Credits
1.4 Contacting the Author
1.5 New Versions of this HOWTO
1.6 New in Recent Versions
1.7 What is a Modem ?
1.8 Does My Computer Contain an Internal Modem ?
1.9 Quick Install
1.9.1 Very Quick Install
1.9.2 Will my modem work under Linux?
1.9.3 External Serial Modem Install
1.9.4 Internal Modems (ISA, PCI and AMR)
1.9.5 Internal Modems: Manual configuration
1.9.5.1 Old ISA Modems
1.9.5.2 Both PCI and ISA: Use setserial to tell the serial driver
1.9.5.3 Use MS Windows to set the BIOS (A last resort method)
1.9.6 All Modems
1.10 dev/modem
2. Modems for a Linux PC
2.1 Many Winmodems Will Not Work with Linux
2.2 External vs. Internal
2.3 Is a Driver Needed ?
2.4 External Modems
2.4.1 Do they all work under Linux?
2.4.2 PnP External Modems
2.4.3 Cabling & Installation
2.4.4 What the Lights (LED's) Mean (for some external modems)
2.5 Internal Modems
2.6 Software-based Modems (winmodems, linmodems)
2.6.1 Introduction to software modems (winmodems)
2.6.2 Linmodems
2.6.3 Linmodem sites and documentation
2.6.4 Software-based modem types
2.6.5 Is this modem a software modem?
2.6.6 Should I get a software modem?
2.7 PCI Modems
2.8 AMR Modems
2.9 USB Modems
2.10 Which Internal Modems might not work with Linux
2.10.1 MWave and some DSP Modems
2.10.2 Old Rockwell (RPI) Drivers
3. Modem Pools, RAS
3.1 Introduction
3.2 Analog Modem Pools, Multi-modem Cards
3.3 Digital Modems, RAS
4. Serial Port and Modem Basics
4.1 Modem Converts Digital to Analog (and conversely)
4.2 What is a Serial Port ?
4.2.1 Intro to Serial
4.2.2 Pins and Wires
4.2.3 Internal Modem Contains Serial Port
4.3 IO Address & IRQ
4.4 Names: ttyS0, ttyS1, etc.
4.5 Interrupts
4.6 Data Compression (by the Modem)
4.7 Error Correction
4.8 Data Flow (Speeds)
4.9 Flow Control
4.9.1 Example of Flow Control
4.9.2 Hardware vs. Software Flow Control
4.9.3 Symptoms of No Flow Control
4.9.4 Modem-to-Modem Flow Control
4.10 Data Flow Path; Buffers
4.11 Modem Commands
4.12 Serial Driver Module
5. Configuring Overview
6. Locating the Serial Port: IO address, IRQs
6.1 What Bus is my Serial Port On?
6.2 IO & IRQ Overview
6.3 PCI Bus Support
6.3.1 Introduction
6.3.2 More info on PCI
6.4 Common mistakes made re low-level configuring
6.5 IRQ & IO Address Must be Correct
6.6 What is the IO Address and IRQ per the driver ?
6.6.1 Introduction
6.6.2 I/O Address & IRQ: Boot-time messages
6.6.3 The /proc directory and setserial
6.7 What is the IO Address & IRQ of my Serial Port Hardware?
6.7.1 Introduction
6.7.2 PCI: What IOs and IRQs have been set?
6.7.3 PCI: Enabling a disabled port
6.7.4 ISA PnP ports
6.7.5 Finding a port that is not disabled (ISA, PCI, PnP, non-PnP)
6.7.6 Exploring via MS Windows (a last resort)
6.8 Choosing Serial IRQs
6.8.1 IRQ 0 is not an IRQ
6.8.2 Interrupt sharing, Kernels 2.2+
6.8.3 What IRQs to choose?
6.9 Choosing Addresses --Video card conflict with ttyS3
6.10 Set IO Address & IRQ in the hardware (mostly for PnP)
6.10.1 Using a PnP BIOS to I0-IRQ Configure
6.11 Giving the IRQ and IO Address to Setserial
7. Configuring the Serial Driver (high-level) "stty"
7.1 Introduction
7.2 Hardware flow control (RTS/CTS)
7.3 Speed Settings
7.4 Ignore CD Setting: clocal
7.5 What is stty ?
8. Modem Configuration (excluding serial port)
8.1 Finding Your Modem
8.2 AT Commands
8.3 Init Strings: Saving and Recalling
8.3.1 Where is my "init string" so I can modify it ?
8.4 Other AT Modem Commands
8.5 Blacklisting
8.6 What AT Commands are Now Set in my Modem?
8.7 Modem States (or Modes)
9. Serial Port Devices /dev/ttyS4, (or /dev/ttys/4) etc.
9.1 Serial Port Names: ttyS4, tts/2, etc.
9.2 The PCI Bus
9.3 Devfs (The Device File System)
9.4 Legacy Serial Port Device Names & Numbers
9.5 More on Serial Port Names
9.6 USB (Universal Serial Bus) Serial Ports
9.7 Link ttySN to /dev/modem
9.8 cua Device Obsolete
10. Interesting Programs You Should Know About
10.1 What is setserial ?
10.1.1 Important information
10.1.2 Introduction
10.1.3 Serial module unload
10.1.4 Giving the setserial command
10.1.5 Configuration file
10.1.6 Probing
10.1.7 Boot-time Configuration
10.1.8 Edit a script (required prior to version 2.15)
10.1.9 Configuration method using /etc/serial.conf, etc.
10.1.10 IRQs
10.1.11 Laptops: PCMCIA
10.2 What is isapnp ?
10.3 What is wvdialconf ?
11. Trying Out Your Modem (Dialing Out)
11.1 Are You Ready to Dial Out ?
11.2 Dialing Out with wvdial
11.3 Dialing Out with Minicom
11.4 Dialing Out with Kermit
12. Dial-In
12.1 Dial-In Overview
12.2 What Happens when Someone Dials In ?
12.3 56k Doesn't Work for Dialin
12.4 Getty
12.4.1 Introduction to Getty
12.4.2 How getty respawns
12.4.3 About mgetty
12.4.4 About uugetty
12.4.5 About getty_em
12.4.6 About agetty
12.4.7 About mingetty, and fbgetty
12.5 Why "Manual" Answer is Best
12.6 Dialing Out while Waiting for an Incoming Call
12.7 Ending a Dial-in Call
12.7.1 Caller logs out
12.7.2 When DTR drops (is negated)
12.7.3 Caller hangs up
12.8 Dial-in Modem Configuration
12.9 Callback
12.10 Distinctive Ring
12.11 Voice Mail
12.12 Simple Manual Dial-In
12.13 Complex GUI Dial-In, VNC
12.14 Interoperability with MS Windows
13. Uugetty for Dial-In (from the old Serial-HOWTO)
13.1 Installing getty_ps
13.2 Setting up uugetty
13.2.1 Modern Modems
13.2.2 Old slow modems
13.2.3 Login Banner
13.3 Customizing uugetty
14. What Speed Should I Use with My Modem?
14.1 Speed and Data Compression
14.2 Where do I Set Speed ?
14.3 Can't Set a High Enough Speed
14.3.1 Speeds over 115.2k
14.3.2 How speed is set in hardware: the divisor and baud_base
14.3.3 Setting the divisor, speed accounting
14.3.4 Crystal frequency is higher than baud_base
14.4 Speed Table
15. Communications Programs And Utilities
15.1 Minicom vs. Kermit
15.2 List of Communication Software
15.2.1 Least Popular Dialout
15.2.2 Most Popular Dialout
15.2.3 Fax
15.2.4 Voicemail Software
15.2.5 Dial-in (uses getty)
15.2.6 Network Connection
15.2.7 Other
15.3 SLiRP and term
15.4 MS Windows
16. Two Modems (Modem Doubling)
16.1 Introduction
16.2 Modem Bonding
16.2.1 EQL
16.2.2 Multilink
17. ISDN "Modems"
17.1 External ISDN "Modems"
17.2 Internal ISDN "Modems"
18. Troubleshooting
18.1 My Modem is Physically There but Can't be Found
18.1.1 Case 1: Winmodem
18.1.2 Cases 2-3
18.1.3 Case 4: Wrong ttySx number
18.1.4 wvdial
18.1.5 minicom (test modem)
18.2 "Modem is busy"
18.3 "You are already online! Hang up first." (from minicom)
18.4 I can't get near 56k on my 56k modem
18.5 Uploading (downloading) files is broken/slow
18.6 For Dial-in I Keep Getting "line NNN of inittab invalid"
18.7 I Keep Getting: ``Id "S4" respawning too fast: disabled for 5 minutes''
18.8 Dial-in: When remote user hangs up, getty doesn't respawn
18.9 NO DIALTONE
18.10 NO CARRIER
18.11 uugetty Still Doesn't Work
18.12 (The following subsections are in both the Serial and Modem HOWTOs)
18.13 Serial Port Can't be Found
18.13.1 Scanning/probing legacy ports
18.14 Linux Creates an Interrupt Conflict (your PC has an ISA slot)
18.15 Extremely Slow: Text appears on the screen slowly after long delays
18.16 Somewhat Slow: I expected it to be a few times faster
18.17 The Startup Screen Shows Wrong IRQs for the Serial Ports.
18.18 "Cannot open /dev/ttyS?: Permission denied"
18.19 "Cannot open /dev/ttyS?"
18.20 "Operation not supported by device" for ttyS?
18.21 "Cannot create lockfile. Sorry"
18.22 "Device /dev/ttyS? is locked."
18.23 "/dev/tty? Device or resource busy"
18.24 "Input/output error" from setserial, stty, pppd, etc.
18.25 "LSR safety check engaged"
18.26 Overrun errors on serial port
18.27 Modem doesn't pick up incoming calls
18.28 Port gets characters only sporadically
18.29 Troubleshooting Tools
19. Flash Upgrades
20. Other Sources of Information
20.1 Misc
20.2 Books
20.3 HOWTOs
20.4 Usenet newsgroups
20.5 Web Sites
21. Appendix A: How Analog Modems Work (technical) (unfinished)
21.1 Modulation Details
21.1.1 Intro to Modulation
21.1.2 Frequency Modulation
21.1.3 Amplitude Modulation
21.1.4 Phase Modulation
21.1.5 Combination Modulation
21.2 56k Modems (V.90, V.92)
21.3 Full Duplex on One Circuit
21.4 Echo Cancellation
22. Appendix B: Analog Voice Infeasible Over Non-Voice Modem
23. Appendix C: "baud" vs. "bps"
23.1 A simple example
23.2 Real examples
24. Appendix D: Terminal Server Connection
25. Appendix E: Cable and DSL modems
25.1 Introduction
25.2 Digital Subscriber Line (DSL)
25.3 Cable Modems
26. Appendix F: Connecting 2 Modems Directly Back-to-Back (Leased Lines).
27. Appendix G: Fax pixels (dots)
28. Appendix H: Stty Hanging Problem (prior to 2000)
29. Appendix G: Antique Modems
29.1 Introduction
29.2 Old CCITT U) and Bell Protocols
29.3 Historical Overview
29.3.1 Teletypes and dumb terminals
29.3.2 PCs and BBSs
29.3.3 The Internet
29.3.4 Speeds
29.4 Proprietary protocols, etc.
29.5 Autobauding
29.6 Modem-to-modem Speed
29.7 Modem-to-serial_port Speed
29.7.1 Same speed required
29.7.2 Equalizing speed
29.7.3 Use "CONNECT" message to set speed
29.7.4 Setting modem-to-modem speeds by the serial speed
29.7.5 Manual bauding
29.7.6 Unsupported speeds
29.7.7 Modern modems, speed buffering
29.8 Before AT Commands
29.9 Acoustic-Coupling
29.10 Data Compression and Error Correction
______________________________________________________________________
[1m1. Introduction[0m
[1m1.1. DSL, Cable, and ISDN Modems in other HOWTOs[0m
This HOWTO covers conventional analog modems for PCs on the PCI, USB,
LPC, and ISA buses. USB and ISDN coverage is weak. For other types
of modems see:
· DSL-HOWTO
· ADSL-Bandwidth-Management-HOWTO
· Cable-Modems-HOWTO (same as Cable Modem Providers HOWTO)
· SuSE ISDN Howto (not a LDP Howto)
<http://brenner.chemietechnik.uni-
dortmund.de/doc/sdb/en/html/isdn.html>
· <http://public.swbell.net/ISDN/overview.html> tutorial on ISDN
· ISDN docs in the kernel documentation subdirectory: "isdn".
· <http://www.isdn4linux.de>
· ``Appendix D: Other Types of Modems''
[1m1.2. Also not well covered: PCMCIA Modems, PPP[0m
For modems on the PCMCIA bus see the PCMCIA-HOWTO: PCMCIA serial and
modem devices. This HOWTO also doesn't cover the details of PPP (used
to connect to the Internet via a modem) or communication programs. If
you want to use a modem to connect to the Internet then you need to
use a program that will automatically set up PPP for you (such as
wvdial). More documentation on ppp should be found in /usr/doc/ppp,
/usr/share/doc/ppp or the like.
[1m1.3. Copyright, Disclaimer, Trademarks, & Credits[0m
[1m1.3.1. Copyright[0m
Copyright (c) 1998-2005 by David S. Lawyer <mailto:dave@lafn.org>
Please freely copy and distribute (sell or give away) this document in
any format. Send any corrections and comments to the document
maintainer. You may create a derivative work and distribute it
provided that you:
1. If it's not a translation: Email a copy of your derivative work (in
a format LDP accepts) to the author(s) and maintainer (could be the
same person). If you don't get a response then email the LDP
(Linux Documentation Project): submit@en.tldp.org.
2. License the derivative work in the spirit of this license or use
GPL. Include a copyright notice and at least a pointer to the
license used.
3. Give due credit to previous authors and major contributors.
If you're considering making a derived work other than a translation,
it's requested that you discuss your plans with the current
maintainer.
[1m1.3.2. Disclaimer[0m
While I haven't intentionally tried to mislead you, there are likely a
number of errors in this document. Please let me know about them.
Since this is free documentation, it should be obvious that I cannot
be held legally responsible for any errors.
[1m1.3.3. Trademarks.[0m
Any brand names (starts with a capital letter such as MS Windows)
should be assumed to be a trademark). Such trademarks belong to their
respective owners.
"Hayes" is a trademark of Microcomputer Products Inc. I use
"winmodem" to mean any modem which originally required MS-Windows and
not in the trademark sense. All other trademarks belong to their
respective owners.
[1m1.3.4. Credits[0m
The following is only a rough approximation of how this this document
was created in the year 2000: About 1/4 of the material here was
lifted directly from Serial-HOWTO v. 1.11 (1997) by Greg Hankins.
<mailto:gregh@twoguys.org> (with his permission). About another 1/4
was taken from that Serial-HOWTO and revised. The remaining 1/2 is
newly created by the new author: David S. Lawyer
<mailto:dave@lafn.org>. Since 2000 much more has been added by the
current author so that little remains of the modem coverage in the old
Serial-HOWTO.
[1m1.4. Contacting the Author[0m
Since I don't follow the many different brands/models of modems please
don't email me with questions about them (or suggestions of which one
to buy). If you are interested in a certain model (to find out if it
works under Linux, etc.) see the huge list at ``Web Sites''. Also,
please don't ask me how to configure a modem unless you've looked over
this HOWTO and still can't do it. I've no personal experience with
software-based modems.
Please let me know of any errors in facts, opinions, logic, spelling,
grammar, clarity, links, etc. But first, if the date is over a month
or two old, check to see that you have the latest version. Please
send me any other info that you think belongs in this document.
[1m1.5. New Versions of this HOWTO[0m
New versions of this Modem-HOWTO should come out every few months.
Your problem might be solved in the latest version. It will be
available to browse and/or download at LDP mirror sites. For a list
of such sites see: <http://www.tldp.org/mirrors.html> If you only
want to quickly compare the date of this the version v0.38, June 2005
with the date of the latest version go to:
<http://www.tldp.org/HOWTO/Modem-HOWTO.html>
[1m1.6. New in Recent Versions[0m
For a full revision history going back to the first version see the
source file (in linuxdoc format) at
<http://www.ibiblio.org/pub/linux/docs/HOWTO/other-formats/sgml/Modem-
HOWTO.sgml.gz>.
· v0.38 May 2005: Eliminated section on Digital Modems in appendix
since it's already covered elsewhere. More on cable modems. ISDN
serial modems. Troubleshooting: Can't find winmodems if no driver.
· v0.37 Feb. 2005: For AMR, codec is on motherboard. Fixed a few
typos. Better clarity for Dial-In. "NO CARRIER" likely not
displayed when remote hangs up.
· v0.36 Feb. 2005 Rewrote "Quick Install" oriented towards PCI. Some
external RS-232 modems are winmodems. /dev/modem.
· v0.35 Dec. 2004: send AT expect OK may not work, 2 modems back-to-
back work OK w/o a phone line
· v0.34 Nov. 2004: Sentence fragment: ... "use up" fixed. url tag
error. Distinctive ring workaround. LPC bus.
· v0.33 Aug. 2004: Modems use telco power, Some external serial
modems need Windows ?? Again: new gromitkc url
· v0.32 Dec. 2003: Still newer gromitkc url w/o pop ups; more on
devfs
· v0.31 Nov. 2003: Mgetty dial-in, setserial rewritten
[1m1.7. What is a Modem ?[0m
A modem (or analog modem) is a device that lets one send digital
signals over an ordinary telephone line not designed for digital
signals. If telephone lines were all digital then you wouldn't need a
modem. But sometimes, a substitute for an analog modem, connected to
a digital phone line, is imprecisely called a "digital modem". A
modem permits your computer to connect to and communicate with the
rest of the world. When you use a modem, you normally use a
communication program or web browser to utilize the modem and dial-out
on a telephone line. Advanced modem users can set things up so that
others may phone in to them and use the computer remotely. This is
called "dial-in".
Oversimplified, there are four basic types of analog modems for a PC:
external serial (RS-232), USB (= external USB), internal, and built-
in. The external serial and USB set on your desk outside the PC while
the other two types are not visible since they're inside the PC. The
external serial modem plugs into a connector on the back of the PC
known as a "serial port". The USB modem plugs into a USB cable. See
``USB Modems''. The internal modem is a card that is inserted inside
the computer. The built-in modem is a chip on the motherboard used
primarily in laptops. What is said in this HOWTO regarding internal
modems will generally apply also to built-in modems. Internal modems
are further subdivided into PCI, ISA, and AMR, depending on whether
they are designed for the PCI or ISA bus, or for an AMR slot.
For an external vs internal comparison see ``External vs. Internal''.
When you get an internal or built-in modem, you also get a dedicated
serial port (which can only be used with the modem and not with
anything else such as an external modem or console terminal). In
Linux, the common serial ports are named ttyS0, ttyS1, etc. (or tts/0,
tts/1 for the device file system (devfs). These ports usually
corresponding respectively to COM1, COM2, etc. in Dos/Windows). But
in special cases, the names are longer such as: ttySHCF0 is the 0th
serial port for a type of winmodem (HCF = Host Controlled Family).
New types of serial ports just add some more letter to ttyS.
See ``Modem & Serial Port Basics'' for more details on how modems and
serial ports work. With a USB modem, the driver simulates a serial
port at for example /dev/ttySHCFUSB or /dev/usb/asm/0 (for devfs).
Modems usually include the ability to send Faxes (Fax Modems). See
``Fax'' for a list of fax software. "Voice" modems can work like an
automatic answering machine and handle voicemail. See ``Voicemail
Software''.
The v.92 protocol can put the modem "on hold" when someone makes an
ordinary voice call to your telephone, provided that you have "call
waiting" from your telephone company. Thus you can get a phone call
while online. As of Jan. 2003 Linux doesn't seem to support it. If
this is the latest version of this HOWTO, let me know about any Linux
support for it. Some linmodem drivers may support it (but what if you
have a hardware modem that doesn't use any linmodem driver?).
[1m1.8. Does My Computer Contain an Internal Modem ?[0m
Internal modems usually have a pair of modular telephone jacks on the
back of the computer. They should be right next to each other and
each one looks like a jack on the interior wall of a building where a
telephone plugs in. One of the pair should be labeled "line" (or the
like) which is where you plug in the telephone line.
Network cards also have modular jacks, but they are seldom in pairs
and are slightly wider since they normally have 8 pins. Internal DSL
"modems" exist and also have modular telephone jacks, but I think they
are not very common (most DSL modems are external) as of 2002.
[1m1.9. Quick Install[0m
[1m1.9.1. Very Quick Install[0m
If you think your modem will work under Linux and needs no special
driver, then just physically install/connect it. Start you computer,
watch the boot-time messages for Linux to find the modem. Note it's
the serial port number such as ttyS2 (/dev/ttyS2). Connect a phone
line to it and dial out with say wvdial (after configuring wvdial).
If the above doesn't work, read on.
[1m1.9.2. Will my modem work under Linux?[0m
So called "winmodems" will work under Linux only if a driver for it
exists and gets installed. In this case it's called a "linmodem"
since it can be made to work under Linux. See modem list
<http://65.70.147.202:8080/gromitkc/winmodem.html> and ``Software-
based Modems (winmodems)''. There's no point of installing a modem
that will not work with Linux.
[1m1.9.3. External Serial Modem Install[0m
At one time (2002 ?) no external serial modem was a winmodem but
that's no longer the case. With a straight-thru or modem cable,
connect the modem to an unused serial port on the PC. Make sure you
know the name of the serial port: in most cases COM1 is ttyS0, COM2 is
ttyS1, etc. You may need to check the BIOS setup menu to determine
this. Plug in the power cord to provide power to the modem. See
``All Modems'' for further instructions.
[1m1.9.4. Internal Modems (ISA, PCI and AMR)[0m
If the modem is both PnP and directly supported by the serial driver
(kernel 2.4 +) or by a winmodem driver that you've installed, then
there is no configuring for you to do since the driver should
configure it.
To physically install a modem card, remove the cover of the PC by
/removing some screws. Find a matching vacant slot for the card next
to the other adapter cards. Before inserting the card in the slot,
remove a small cover plate on the back of the PC so that the telephone
jacks on the card will be accessible from the rear of the PC. Then
carefully align the card with the slot and push the card all the way
down into the slot. Attach the card with a mounting screw (usually
3mm, .5mm pitch --don't use the wrong size).
You may watch the boot-time messages to see if your modem is detected.
Use "dmesg" to see them or shift-page-up to scroll the screen back
after they have flashed by.
[1m1.9.5. Internal Modems: Manual configuration[0m
Normally, you don't need to do this manual configuration since the
modem's serial port may be detected and assigned a port at boot-time.
For example: ttyS14 at I/O 0x6450 (IRQ = 10). Otherwise (or if there
is some special reason to change the configuration) then you need to
configure it yourself (or perhaps update your kernel to increases the
likelihood that the modem gets detected). If your modem has no ttyS
number assigned to it, it can't be used until it gets a ttyS number
(like ttyS10). It thus can't be detected by application programs such
as dialers or minicom. But it might be found by using say "lspci -v"
if it's on the PCI bus.
Finding a lost modem may not be easy and you may need to read a lot
more of this HOWTO. Once found, you need to use the "setserial"
program to manually assign it to an available ttyS? port of your
choice . For this you need to know both it's IO address (such as
0x6450) and its IRQ (such as 10). In the worst case, the modem has
been disabled by a failing to be detected and enabled by the BIOS (or
Linux) and doesn't have any IO address nor IRQ number. But you may
still be able to find it. Older modems could be disabled by a jumper
on the card or in rare cases by MS software.
You may have some choice of IRQs and IO addresses (including the case
where you are able to change what the BIOS has set). See ``Choosing
Serial IRQs'' and ``Choosing Addresses''.
[1m1.9.5.1. Old ISA Modems[0m
ISA modems normally use ttyS0 - ttyS3. For old modems with jumpers
look at the modem manual or look for printing on the modem card that
tells you what the jumpers do. They have standard IO addresses
corresponding to the ttySx. For example you may find it feasible to
use /dev/ttyS2 at IO address 0x3e8 and IRQ 11.
If it has no jumpers then it's likely a Plug-and-Play modem which the
BIOS may configure when you power one your PC. Typing "pnpdump
--dumpregs" should find it. If you need to set or change them use
"isapnp". Use the "pnpdump" program to see what changes are possible.
[1m1.9.5.2. Both PCI and ISA: Use setserial to tell the serial driver[0m
You must find the file where "setserial" is run at boot-time and add a
line something like: "setserial /dev/ttyS2 irq 5 port 0x0b8". For
setserial v2.15 and later the results of running "setserial" on the
command line may (or may not) be saved to file named serial.conf or
autoserial.conf. It might be in say the /etc directory or in the
/var/lib/setserial directory (use "locate to find it). it runs each
time you boot. See ``What is Setserial'' for more info. See the next
subsection ``All Modems'' for further instructions on quick
installation.
[1m1.9.5.3. Use MS Windows to set the BIOS (A last resort method)[0m
If you are using the BIOS to configure you may attempt to use MS
Windows9x to "force" the BIOS to set a certain IRQ and/or IO. It can
set them into the PnP BIOS's flash memory where they will be used to
configure for Linux as well as Windows. See "Plug-and-Play-HOWTO and
search for "forced" (occurs in several places). For Windows3.x you
can do the same thing using the ICU under Windows 3.x. A few modems
have a way to disable PnP in the modem hardware using software (under
Windows) that came with the modem.
[1m1.9.6. All Modems[0m
Plug the modem into a telephone line. Then configure a dialing
program. If you have an Internet Service Provider (ISP) you might
configure one of these : wvdial, pppconfig, gnome-ppp, modem lights
(Gnome) or kppp. They not only dial out but start PPP, which you need
to connect to the Internet. Otherwise, you might try configuring the
minicom dialer which isn't designed for connecting to the Internet,
but is good for testing. Whether it's minicom or a dialer that starts
PPP, set the serial port speed to a baud rate a few times higher than
the bit rate of your modem. See ``Speed Table'' for more details on
the "best" speeds to use. Tell it the full name of your serial port
such as /dev/ttyS1 (or /dev/ttys/1).
Minicom is one way to set up and test your modem. Set hardware flow
control (RTS/CTS). With minicom you may check to see if your modem is
there (and ready to dial). Once you've set up minicom, type the
command: AT, hit enter and you should see an "OK" response which comes
directly from the modem. See ``Dialing Out with Minicom''.
[1m1.10. dev/modem[0m
If your modem is on say /dev/ttyS2, you may want to link that to
/dev/modem. It's not really necessary to do this since you can write
down (or remember) say ttyS2 and tell it to programs that use the
modem. It may be simpler to just link it. To link it, type say ln -s
/dev/ttyS2 /dev/modem . Note "ttyS2" is just for example. It might
actually be ttyS14, etc. Or use Red Hat's modemtool (or the like) to
link it. But once you link it, be sure that all programs that use the
modem use /dev/modem and not /dev/ttyS2, otherwise two programs may
try to use the modem at the same time without knowing they are doing
this. System software was written around 2000 to fix this problem but
it may not be in recent kernels (like 2.6).
[1m2. Modems for a Linux PC[0m
[1m2.1. Many Winmodems Will Not Work with Linux[0m
Unfortunately, some software modems (winmodems) will not work with
Linux due to lack of Linux drivers. Configuring the software modems
that can be made to work with Linux ranges from very easy
(automatically) to difficult, depending on both the modem, your
skills, and how easy it is to find info about your modem --info that
is not all in this HOWTO. If you buy a new one that you're not sure
will work under Linux, try to get an agreement that you can return it
for a refund if it doesn't work out.
Even if your modem works with Linux it can't be used until the serial
port it's located on is enabled and made known to the operating
system. For a detailed explanation of this (or if boot-time messages
don't show your modem's serial port) study this HOWTO or see Plug-and-
Play-HOWTO.
[1m2.2. External vs. Internal[0m
A modem for a PC may be either internal, external serial, or external
USB. The internal one is installed inside of your PC (you must remove
screws, etc. to install it). An external one just plugs in to a
cable: USB cable (USB modem) or to the serial port (RS-232 serial
modem). As compared to external serial modems, the internal modems
are less expensive, are less likely to to suffer data loss due to
buffer overrun, and usually use less electricity. An internal modem
obviously doesn't use up any desk space.
External serial modems are usually easier to install and usually has
less configuration problems provided the serial port you'll connect it
to is configured OK. External USB modems are more likely to be
winmodems and are reportedly usually more difficult to deal with than
external serial modems. External modems have lights which may give
you a clue as to what is happening and aid in troubleshooting. The
fact that the serial port and modem can be physically separated also
aids in troubleshooting. External modems are easy to move to another
computer. If you need to turn the power off to reset your modem (this
is seldom necessary) then with an external you don't have to power
down the entire PC.
Unfortunately, most external serial modems have no switch to turn off
the power supply when not in use and thus are likely to consume a
little electricity even when turned off (unless you unplug the power
supply from the wall). Each watt they draw usually costs you over
$1/yr. Another possible disadvantage of an external is that you will
be forced to use an existing serial port which may not support a speed
of over 115,200 bps (although as of late 2000 most new internal modems
don't either --but some do). For details ``Can't Set a High Enough
Speed''
[1m2.3. Is a Driver Needed ?[0m
Any modem, of course, needs the serial driver that comes with Linux
(either built into the kernel or as a module). For PCI, this driver
should also detect the modem but it's not really a modem driver since
it just detects which serial port the modem is on.
But what about modem drivers? Any software modem (winmodem, linmodem)
must have a modem driver (if it exists for Linux). Hardware modems
don't really need any modem driver unless you want to use special
features such as voice and "modem on hold".
Software modems require software to run them and obviously do need a
driver. The drivers for MS Windows are *.exe programs which will not
run under Linux. So you must use a Linux driver (if it exists). See
``Software-based Modems (winmodems, linmodems)''
[1m2.4. External Modems[0m
[1m2.4.1. Do they all work under Linux?[0m
At one time (2002 ?) all external modems would work under Linux. But
then came the controllerless external modem which wouldn't. If the
box says it requires Windows with no mention of Linux it could mean
just that. Could it be that Windows software is provided for "modem
on hold" and for use as an answering machine, etc., but that otherwise
it will work under Linux? Linux may not support these features very
well if at all. If this is a recent version of Modem-HOWTO, let me
know of your experience with this.
[1m2.4.2. PnP External Modems[0m
Many external modems are labeled "Plug and Play" (PnP). If they are
hardware modems, they should all work as non-PnP modems. While the
serial port itself may need to be configured (IRQ number and IO
address) unless the default configuration is OK, an external modem
uses no such IRQ/IO configuration. You just plug the modem into the
serial port.
The PnP modem has a special PnP identification built into it that can
be read (thru the serial port) by a PnP operating system. Such an
operating system would then know that you have a modem on a certain
port and would also know the id number. If it's a controllerless
modem, it could try to locate a driver for it. It could also tell
application programs what port your modem is on (such as /dev/ttyS2 or
COM3). But Linux may not be able to do this. Thus you may need to
configure your application program manually by giving it the ttyS
number (such as /dev/ttyS2). Some programs like wvdial can probe for
a modem on various ports.
[1m2.4.3. Cabling & Installation[0m
Connecting an external modem is simple compared to connecting most
other devices to a serial port that require various types of "null
modem" cables (which will not work for modems). Modems use a straight
through cable, with no pins crossed over. Most computer stores should
have one. Make sure you get the correct gender and number of pins.
Hook up your modem to one of your serial ports. If you are willing to
accept the default IRQ and IO address of the port you connect it to,
then you are ready to start your communication program and configure
the modem itself.
[1m2.4.4. What the Lights (LED's) Mean (for some external modems)[0m
· TM Test Modem
· AA Auto Answer (If on, your modem will answer an incoming call)
· RD Receive Data line = RxD
· SD Send Data line = TxD
· TR data Terminal Ready = DTR (set by your PC)
· RI Ring Indicator (If on, someone is "ringing" your modem)
· OH Off Hook (If off, your modem has hung up the phone line)
· MR Modem Ready = DSR ??
· EC Error Correction
· DC Data Compression
· HS High Speed (for this modem)
[1m2.5. Internal Modems[0m
An internal modem is installed in a PC by taking off the cover of the
PC and inserting the modem card into a vacant slot on the motherboard.
There are modems for PCI slots, other modems for the older ISA slots,
and ARM software "modems" for the new small AMR slot. Only some newer
PCs will have ARM slots. While external modems plug into the serial
port (via a short cable) the internal modems have the serial port
built into the modem. In other words, the modem card is both a serial
port and a modem.
Setting the IO address and IRQ for a serial port was formerly done by
jumpers on the card. These are little black rectangular "cubes" about
5x4x2 mm in size which push in over pins on the card. Plug-and-Play
modems (actually the serial port part of the modems) don't use jumpers
for setting these but instead are configured by sending configuration
commands to them over the bus inside the computer. Such configuration
commands can be sent by a PnP BIOS, by the isapnp program (for the ISA
bus only), by setpci (for the PCI bus), or by newer serial device
drivers for certain modems. Under Linux you may have a choice of how
to configure the ones that don't get io-irq configured by the serial
driver.
1. ISA bus: Use "isapnp" which may be run automatically at every boot-
time
2. Let a PnP BIOS do it, and then maybe tell setserial the IO and IRQ
3. PCI bus: Use lspci -vv to look at it and setpci to configure.
See ``Quick Install'' for more details, especially for the PCI bus.
[1m2.6. Software-based Modems (winmodems, linmodems)[0m
[1m2.6.1. Introduction to software modems (winmodems)[0m
Software modems turn over some (or even almost all) of the work of the
modem to the main processor (CPU) chip of your computer (such as a
Pentium chip). This requires special software (a modem driver) to do
the job. Until late 1999, such software was released only for MS
Windows and wouldn't work with Linux. Even worse was that the maker
of the modem kept the interface to the modem secret so that no one
could write a Linux driver for it (even though a few volunteers were
willing to write Linux drivers).
But things have improved some since then so that today (late 2001)
many such modems do have a linux driver. There is no standard
interface so that different brands/models of software-modems need
different drivers (unless the different brands/models happen to use
the same chipset internally). But some drivers may not work perfectly
nor have all the features that a MS Windows driver has.
Another name for a software modem (used by MS) is "driver-based
modem". The conventional hardware-based modem (that works with Linux)
doesn't need a modem driver (but does use the Linux serial driver)
After about mid-1998 most new internal modems were software modems.
Software modems fall into 2 categories: linmodems and winmodems.
Winmodems will only work under MS Windows. Linmodems will work under
Linux. They formerly were mostly winmodems so some also call them
"winmodems". The term "Winmodem" is also a trademark for a certain
model of "winmodem" but that's not the meaning of it in this document.
[1m2.6.2. Linmodems[0m
In late 1999, two software-based modems appeared that could work under
Linux and were thus called "linmodems". Lucent Technologies (LT)
unofficially released a Linux binary-only code to support most of its
PCI modems. PC-TEL (includes "Zoltrix") introduced a new software-
based modem for Linux. After that, interest increased for getting
winmodems to work under linux. There is a GPL'ed driver for Intel's
(Modem Silicon Operations) MD563x HaM chipset (nee Ambient division of
Cirrus Logic). As of mid-2001 there are also drivers for: Conexant
HSF and HCF, Motorola SM56 (support terminated), ESS (ISA only), and
IBM's Mwave for Thinkpads 600+. See <http://linmodems.org>.
What percent of software modems now (2001) work under Linux? Well,
there's a number of modem chips not supported: Lucent/Agere ARM
(Scorpio), 3COM/US Robotics, some SmartLink (3 different chipsets),
Ambient HSP, and possibly others. So it seems that over half the
software modem chips were supported as of late 2001. As of 2005 it
seems that the situation hasn't improved and may even have
deteriorated some. Why? Well, Linux on the Desktop didn't grow as
fast as expected and many PC users went for higher speed cable modems
and DSL.
There's also the problem that many of the drivers will only work with
older versions of the Linux kernels.
Be warned in advance that determining if your modem is a linmodem may
not be easy. You may need to first find out what chipset you have and
who makes it. Just knowing the brand and model number of your modem
may not be sufficient. One method is to download the scanModem tool
from <http://linmodems.org> but the results may be hard to decipher
and you may need to ask for help from the linmodems mailing list.
Another way to find this out using say "lspci -v" and then looking up
the chip maker using the long modem number. This requires checking a
database or searching the Internet. Still another way is to look at
the fine print on the chips on the modem card. All this is not always
simple. It could happen that you will put a lot of effort into this
only to get the bad news that your modem isn't supported. But even if
it is supported, support may only be for an old version of the kernel.
See Linmodem-HOWTO for more details.
[1m2.6.3. Linmodem sites and documentation[0m
· Linmodem-HOWTO
· Winmodems-and-Linux-HOWTO (not as well written as Linmodem-HOWTO)
· <http://linmodems.org> is a project to turn winmodems into
linmodems. Has a mailing list.
· Conexant+Rockwell-modem-HOWTO
· modem list <http://65.70.147.202:8080/gromitkc/winmodem.html> Has
links to linmodem info.
· PCTel-HSP-MicroModem-Configuration-mini-HOWTO
[1m2.6.4. Software-based modem types[0m
There are two basic types of software modems. In one type the
software does almost all of the work. The other is where the software
only does the "control" operations (which is everything except
processing the digital waveshapes --to be explained later). Since the
hardware doesn't do the control it's called a "controllerless" modem.
The first type is an all-software modem (sometimes just called a
software modem).
For both of these types there must be analog hardware in the modem to
generate an electrical waveshape to send out the phone line. It's
generated from a digital signal (which is sort of a "digital
waveshape"). It's something like the digital electronics creates a
lot of discrete points on graph paper and then the modem draws a
smooth curve thru them. There must also be hardware to convert the
incoming waveshape to digital. This is just analog-to-digital
conversion (and conversely). It's done by a codec (coder-decoder).
The incoming digital waveshape must be converted to a data byte
stream. This is part of the demodulation process, while turning data
bytes into a digital waveshape is part of the modulation process. The
modem can't just send the incoming data byte stream to the PC but must
first do decompression, error correction, and convert from serial to
the parallel bus of the computer. It's the reverse sequence for an
outgoing data byte stream.
The difference between the two types of software-based modems is where
the digital modulation takes place. In the all-software modem this
modulation is done in the CPU using a Host Signal Processor (HSP). In
the controllerless modem it's done in the modem but all other digital
work is done by the CPU. This other digital work consists of dealing
with AT-commands, data compression, error correction, and simulating a
serial port. In the all-software modem, there are still two items
handled by hardware: the A/D conversion of waveshapes by the codec and
echo cancellation.
[1m2.6.5. Is this modem a software modem?[0m
How do you determine if an internal modem is a software modem? First
see if the name, description of it, or even the name of the MS Windows
driver for it indicates it's a software modem: HSP (Host Signal
Processor) , HCF (Host Controlled Family), HSF (Host Signal Family),
controllerless, host-controlled, host-based, and soft-... modem. If
it's one of these modem it will only work for the cases where a Linux
driver is available. Since software modems cost less, a low price is
a clue that it's a software modem.
If you don't know the model of the modem and you also have Windows on
your Linux PC, click on the "Modem" icon in the "Control Panel". Then
see the modem list <http://65.70.147.202:8080/gromitkc/winmodem.html>.
If the above doesn't work (or isn't feasible), you can look at the
package the modem came in (or a manual). Read the section on the
package that says something like "Minimum System Requirements" or just
"System Requirements".
A hardware modem will work fine on old CPUs (such as the 386 or
better). So if it requires a modern CPU (such as a Pentium or other
"high speed" CPU of say over 150 MHz) this is a clue that it's a all-
software modem. If it only requires a 486 CPU (or better) then it's
likely a host-controlled software modem. Saying that it only works
with Windows is also bad news. However, even in this case there may
be a Linux driver for it or it could be a mistake in labeling.
Otherwise, it may be a hardware modem if it fails to state explicitly
that you must have Windows. By saying it's "designed for Windows" it
may only mean that it fully supports Microsoft's plug-and-play which
is OK since Linux uses the same plug-and-play specs (but it's harder
to configure under Linux). Being "designed for Windows" thus gives no
clue as to whether or not it will work under Linux. You might check
the Website of the manufacturer or inquire via email. Some
manufacturers are specifically stating that certain models work under
Linux. Sometimes they are linmodems that require you to obtain and
install a certain linmodem driver.
[1m2.6.6. Should I get a software modem?[0m
Only if you know there is a Linux driver for it that works OK. But
there may be a problem if the driver isn't being maintained and as a
result doesn't work with future versions of the kernel. Also, the
driver may not have full functionality. Besides the problems of
getting a satisfactory driver, what are the pros and cons of software
modems? Since the software modem uses the CPU to do some (or all) of
its work, the software modem requires less on-board electronics on the
modem card and thus costs less. At the same time, the CPU work load
is increased by the modem which may result in slower operation.
The percentage of loading of the CPU by the modem depends on both what
CPU you have and whether or not it's an all-software modem. For a
modern CPU and a modem that only uses the CPU as a controller, there's
little loss of performance. Even if it's an all-software modem, you
will not suffer a loss of performance if there are no other CPU-
intensive tasks are running at the same time. Of course, when you're
not using the software modem there is no degradation in performance at
all.
Is the modem cost savings worth it? In many cases yes, especially if
you don't use the modem much and/or are not running any other CPU
intensive tasks when the modem is in use. The savings in modem cost
could be used for a better CPU which would speed things up a little.
But the on-board electronics of a hardware modem can do the job more
efficiently than a general purpose CPU (except that it's not efficient
at all when it's not in use). So if you use the modem a lot it's
probably better to avoid all-software modems.
[1m2.7. PCI Modems[0m
A PCI modem card is one which inserts into a PCI-bus slot on the
motherboard of a PC. While many PCI winmodems will not work under
Linux (no driver available) other PCI modems will work under Linux.
The Linux serial driver has been modified to support certain PCI
hardware modem cards (but not winmodems/linmodems). If it's a
linmodem, it will work only if you install a certain linmodem driver.
If the Linux serial driver supports your hardware modem then the
driver will set up the PnP configuration for you. See ``PCI Bus
Support Underway''. If no special support for your PCI hardware modem
is in the Linux serial driver it may still work OK but you have to do
some work to configure it.
[1m2.8. AMR Modems[0m
These are mainly used in laptops. They are all winmodems that insert
into a special AMR (Audio Modem Riser) slot on the motherboard. Audio
cards or combined audio-modem cards are sometimes used in this slot.
The slot's main use is for HSF type modems where the CPU does almost
all of the work. This results in a small "modem" card and thus a
short AMR slot. The motherboard has a codec which takes digital
output from the the CPU and generates analog voltage waves at the ARM
slot (and conversely). Thus the "modem" that plugs into the slot has
little to do except to interface the telephone line with the codec.
Linux supports at least one AMR modem. lspci -v should display it.
[1m2.9. USB Modems[0m
USB = Universal Serial Bus. Most USB modems are winmodems, so many
will not work with Linux. Linux has support for modems that conform
to the USB Communication Device Class Abstract Control Model (= USB
CDC ACM). There's a module for ACM named acm.o. See the /usb/acm.txt
document in the kernel documentation directory (/usr/share/doc/kernel-
doc-2.6.x in Debian, perhaps /usr/doc/kernel... in some
distributions). The ACM "serial port" for the first (0th) such modem
is: /dev/usb/acm/0 or possibly /dev/usb/ttyACM0. This should be the
case regardless of whether or not you use the new "device file
system". It's not really a serial port, but the driver makes it look
like a serial port to software which uses the modem.
Since the bandwidth on the USB is high it's possible to send a lot
more that just data to a USB modem. This means that it's feasible to
create a USB winmodem where the driver does most of the modem's work
on the CPU and sends the results to the modem. So beware of USB
winmodems (unless they have Linux support).
[1m2.10. Which Internal Modems might not work with Linux[0m
· ``Software-based Modems (winmodems, linmodems)'' Only about half
have a Linux driver available.
· ``MWave and DSP Modems'' might work, but only if you first start
Windows/Dos each time you power on your PC.
· Modems with ``Old Rockwell (RPI) Drivers'' work but with reduced
performance.
[1m2.10.1. MWave and some DSP Modems[0m
Note that there's now a Linux driver for the ACP (Mwave) modem used in
IBM Thinkpads 600+. See the mini-HOWTO: ACP-Modem.
While hardware modems used use DSPs (Digital Signal Processors) some
of these DSPs are programmed by a driver which must be downloaded from
the hard disk to the DSPs memory just before using the modem.
Unfortunately, such downloading is normally done by Dos/Windows
programs (which doesn't work for Linux). But there has been
substantial success in getting some of these modems to work with
Linux. For example, there is a Linux driver available to run a Lucent
(DSP) modem.
Ordinary modems that work fine with Linux (without needing a driver
for the modem) often have a DSP too (and may mention this on the
packaging), but the program that runs the DSP is stored inside the
modem. These work fine under Linux. An example of a DSP modem that
has problems working under Linux is the old IBM's Aptiva MWAVE.
One way to get some DSP modems to work with Linux is to boot from DOS
(if you have it on your Linux PC). You first install the driver under
DOS (using DOS and not Window drivers). Then start Dos/Windows and
start the driver for the modem so as to program the DSP. Then without
turning off the computer, start Linux.
One may write a "batch" file (actually a script) to do this. Here is
an example but you must modify it to suit your situation.
rem mwave is a batch file supplied by the modem maker
call c:\mww\dll\mwave start
rem loadlin.exe is a DOS program that will boot Linux from DOS (See
rem Config-HOWTO).
c:\linux\loadlin f:\vmlinuz root=/dev/hda3 ro
One may create an icon for the Window's desktop which points to such a
batch file and set the icon properties to "Run in MSDOS Mode". Then
by clicking on this icon one sets up the modem and goes to Linux.
Another possible way to boot Linux from DOS is to press CTRL-ALT-DEL
and tell it to reboot (assuming that you have set things up so that
you can boot directly into Linux). The modem remains on the same com
port (same IO address) that it used under DOS.
The Newcom ifx modem needs a small kernel patch to work correctly
since its simulation of a serial port is non-standard. The patch and
other info for using this modem with Linux is at
<http://quinine.pharmacy.ohio-state.edu/~ejolson/linux/newcom.html>.
[1m2.10.2. Old Rockwell (RPI) Drivers[0m
Some older Rockwell chips need Rockwell RPI (Rockwell Protocol
Interface) drivers for compression and error correction. They can
still be used with Linux even though the driver software works only
under MS Windows. This is because the MS Windows software (which you
don't have) does only compression and error correction. If you are
willing to operate the modem without compression and error correction
then it's feasible to use it with Linux. To do this you will need to
disable RPI by sending the modem (via the initialization string) a
"RPI disable" command each time you power on your modem. On my old
modem this command was +H0. Not having data compression available
makes it slower to get webpages but is just as fast when downloading
files that are already compressed.
[1m3. Modem Pools, RAS[0m
[1m3.1. Introduction[0m
A "modem pool" is a group of modems which are normally used to receive
incoming calls. Today, many such modems may be on a single card.
ISPs once used modem pools so that customers could call in to the ISP,
but today, the RAS (Remote Access Server) has replaced modem pools for
ISPs. RAS works for incoming calls at near 56k (V.90 and V.92) and
uses what amounts to "digital modems". Modem pools use the older
analog modems and can only go to 33.6 kbps for incoming calls. Thus
analog modem pools are more likely to be used by small organizations
that don't want to use the more expensive RAS. A RAS is in a sense a
digital modem pool.
An analog modem pool may be provided by an analog multi-port modem
card. In olden days it was many modems in an external chassis
(something like an external modem). Such modems could be analog
modems similar to modems used for home/office PCs (can't send above
33.6k even if they are labeled "56k modems"). A RAS will use "digital
modems" which can send at nearly 56k (if you have a good line). The
"digital modems" require a digital connection to the telephone line
and don't use any serial ports at all. All of these modem pools (or
RAS's) will require that you install special drivers for them.
[1m3.2. Analog Modem Pools, Multi-modem Cards[0m
A "multimodem card" is short for "multiport modem card". Some put a
hyphen after "multi": multi-modem or multi-port. An analog modem pool
is just many analog modems (the common home/office modem) provided
either on an internal plug-in card or in an external chassis. Each
modem comes with a built-in serial port. There is usually a system of
sharing interrupts or of handling interrupts by their own electronics,
thus removing much of this burden from the CPU. Note that these
modems are not "digital modems" and will thus not be able to use 56k
for people who dial-in.
Here is a list of some companies that make analog multiport modem
cards which plug into slots in a PC. 8 modems/card is common. The
cards listed claim to work with Linux and the websites should point
you to a driver for them.
Multi-modem Cards (analog, not digital):
· Equinox SST Multi-modem. PCI, 56k, 4 or 8 ports
<http://www.equinox.com/product/multi-modem.htm>
· MultiModemISI by Multi-Tech Systems. 56k or 33.6k, PCI, 4 or 8
ports. ISDN/56k hybrids.
<http://www.multitech.com/PRODUCTS/MultiModemISI/>
· PCI-RAS cards by Perle. 56k, 4 or 8 ports.
<http://www.perle.com/solutions/app_notes/multi_modem/pci_ras_fax.html>
· RocketModem by Comtrol. ISA 33.6k, 4 or 8 port.
<http://www.comtrol.com/sales/specs/rm.htm>
· RocketModem II by Comtrol. PCI 56k, 4 or 6 port
<http://www.comtrol.com/sales/specs/rmii.htm>
· RockForce. 56k, 2 or 4 port Two port V.92/V.44
<http://www.mainpine.com/> #RockForce+ Two port V.90
(www.mainpine.com/prodrockplus.html) #RockForceDUO Two port
V.92/V.44 (www.mainpine.com/prodduo.html) #RockForceQUATRO Four
port V.92/V.44 (www.mainpine.com/prodquatro.html) #RockForceDUO+
Two port V.92/V.44/V.34 SuperG3 Fax =
#(www.mainpine.com/prodduoplus.html) #RockForceQUATRO+ Four port
V.92/V.44/V.34 SuperG3 Fax =
#(www.mainpine.com/prodquatroplus.html) #
· Multi-modem communication adapters by Digi.
<http:/www.dgii.com/solutions/mmcommadapters/index.html>
[1m3.3. Digital Modems, RAS[0m
"Digital modems" are much different than the analog modems that most
people use in their PCs. But they can communicate with analog modems
at the other end of the phone line. ISP's use "digital modems" to send
out data at almost 56k bps to 56k modems in homes and offices. The
"digital modem" requires a digital connection to the telephone line
(such as T1, EI, ISDN PRI, etc.). Except for some serial ISDN
"modems", they don't use serial ports for the interface to the
computer. Instead, they interface directly to a computer bus via a
special card(s) (which may also contain the "digital modems"). They
are often a component of "remote access servers" (RASs) or "digital
modem pools"
You may already know that each time you make a telephone call from an
analog device (a telephone or a modem) it gets converted by the
telephone company to a digital signal. Then it's transmitted to near
its destination as a digital signal and finally converted back into an
analog signal just before it reaches it's destination. But it's also
possible to receive this digital signal directly from the telephone
company if you have what is called a "T1" line, etc.
The cables from the phone company that carry digital signals have been
designed for high bandwidth so that the same cable carries many
telephone calls. It's done by what's called "time-division
multiplexing". A single phone call in a cable is carried on two
different channels, one for each direction. So the RAS must connect
each such channel-pair to the appropriate "digital modem" that
services that phone call. Such tasks are done by what is sometimes
called a "... concentrator".
Now the digital signal received by a "digital modem" may really
represent an analog signal which has been sent to it by an analog
modem. This is because when you send an analog signal (including
ordinary voice) to the telephone company, it gets converted into
digital by the phone company. One way for the digital modem to deal
with this digital signal would be to convert it to an analog signal
and then put that thru an analog modem to get the digital data sent by
the analog modem. But why do all this work? Since the signal is
already in digital form, why not process it digitally? That's how
it's done. The digital signal is processed and converted to another
digital stream of bytes which represents data bytes sent by the analog
modem. A "digital signal processor" (DSP) is commonly used for this
task. A CPU could also handle it but it would be heavily loaded.
Likewise, a "digital modem" must handle sending digital signals in the
opposite direction from a RAS to a digital telephone line. Thus it
only makes digital-to-digital conversions and doesn't deal in analog
at all. It thus is not really a modem at all since it doesn't
modulate any analog carrier. So the name "digital modem" is a
misnomer but it does do the job formerly done by modems. Thus some
"digital modems" call themselves "digital signal processors", or
"remote access servers", etc. and may not even mention the word
"modem".
Such a RAS system may be a stand-alone proprietary server, a chassis
containing digital modems that connects to a PC via a special
interface card, or just a card itself. Digi calls one such card a
"remote access server concentrator adapter". One incomplete
description of what is needed to become an ISP is: See What do I need
to be an ISP?
</http://www.cyclades.com/solutions/techtalk/techtalk0l.php>.
Cyclades promotes their own products here so please do comparison
shopping before buying anything.
[1m4. Serial Port and Modem Basics[0m
You don't have to understand the basics to use and install a modem.
But understanding it may help to determine what is wrong if you run
into problems. After reading this section, if you want to understand
it even better you may want to see ``How Modems Work'' in this
document (not yet complete). More details on the serial port
(including much of this section) will be found in Serial-HOWTO.
[1m4.1. Modem Converts Digital to Analog (and conversely)[0m
Most all telephone main lines are digital already but the lines
leading to your house (or business) are usually analog which means
that they were designed to transmit a voltage wave which is an exact
replica of the sound wave coming out of your mouth. Such a voltage
wave is called "analog". If viewed on an oscilloscope it looks like a
sine wave of varying frequency and amplitude. A digital signal is
like a square wave. For example 3 v (volts) might be a 1-bit and 0 v
could be a 0-bit. For most serial ports (used by external modems) +12
v is a 0-bit and -12 v is a 1-bit (some are + or - 5 v).
To send data from your computer over the phone line, the modem takes
the digital signal from your computer and converts it to "analog". It
does this by both creating an analog sine wave and then "MODulating"
it. Since the result still represents digital data, it could also be
called a digital signal instead of analog. But it looks something
like an analog signal and almost everyone calls it analog. At the
other end of the phone line another modem "DEModulates" this signal
and the pure digital signal is recovered. Put together the "mod" and
"dem" parts of the two words above and you get "modem" (if you drop
one of the two d's). A "modem" is thus a MODulator-DEModulator. Just
what modulation is may be found in the section ``Modulation Details''.
[1m4.2. What is a Serial Port ?[0m
[1m4.2.1. Intro to Serial[0m
The UART serial port (or just "serial port for short" is an I/O
(Input/Output) device. Since modems have a serial port between them
and the computer, it's necessary to understand the serial port as well
as the modem.
Most PC's have one or two serial ports. Each has a 9-pin connector
(sometimes 25-pin) on the back of the computer. Computer programs can
send data (bytes) to the transmit pin (output) and receive bytes from
the receive pin (input). The other pins are for control purposes and
ground.
The serial port is much more than just a connector. It converts the
data from parallel to serial and changes the electrical representation
of the data. Inside the computer, data bits flow in parallel (using
many wires at the same time). Serial flow is a stream of bits over a
single wire (such as on the transmit or receive pin of the serial
connector). For the serial port to create such a flow, it must
convert data from parallel (inside the computer) to serial on the
transmit pin (and conversely).
Most of the electronics of the serial port is found in a computer chip
(or a part of a chip) known as a UART. For more details on UARTs see
the section "What are UARTS" in the Serial-HOWTO.
But you may want to finish this section first so that you will
hopefully understand how the UART fits into the overall scheme of
things.
[1m4.2.2. Pins and Wires[0m
Old PC's used 25 pin connectors but only about 9 pins were actually
used so today most connectors are only 9-pin. Each of the 9 pins
usually connects to a wire. Besides the two wires used for
transmitting and receiving data, another pin (wire) is signal ground.
The voltage on any wire is measured with respect to this ground. Thus
the minimum number of wires to use for 2-way transmission of data is
3. Except that it has been known to work with no signal ground wire
but with degraded performance and sometimes with errors.
There are still more wires which are for control purposes (signalling)
only and not for sending bytes. All of these signals could have been
shared on a single wire, but instead, there is a separate dedicated
wire for every type of signal. Some (or all) of these control wires
are called "modem control lines". Modem control wires are either in
the asserted state (on) of +12 volts or in the negated state (off) of
-12 volts. One of these wires is to signal the computer to stop
sending bytes out the serial port cable. Conversely, another wire
signals the device attached to the serial port to stop sending bytes
to the computer. If the attached device is a modem, other wires may
tell the modem to hang up the telephone line or tell the computer that
a connection has been made or that the telephone line is ringing
(someone is attempting to call in). See the Serial-HOWTO: Pinout and
Signals for more details.
[1m4.2.3. Internal Modem Contains Serial Port[0m
For an internal modem there is no 9-pin connector but the behavior is
almost exactly as if the above mentioned cable wires existed. Instead
of a a 12 volt signal in a wire giving the state of a modem control
line, the internal modem may just use a status bit in its own memory
(a register) to determine the state of this non-existent "wire". The
internal modem's serial port looks just like a real serial port to the
computer. It even includes the speed limits that one may set at
ordinary serial ports such as 115200 bits/sec.
Unfortunately for Linux, many internal modems today use software
(running on the CPU) to do much of the modem's work. Unfortunately,
such software may be only available for the MS Windows OS (it hasn't
been ported to Linux). Thus you can't use some of these modems with
Linux See ``Software-based Modems (winmodems)''.
[1m4.3. IO Address & IRQ[0m
Since the computer needs to communicate with each serial port, the
operating system must know that each serial port exists and where it
is (its I/O address). It also needs to know which wire (IRQ number)
the serial port must use to request service from the computer's CPU.
It requests service by sending an interrupt voltage on this wire.
Thus every serial port device must store in its non-volatile memory
both its I/O address and its Interrupt ReQuest number: IRQ. See
``Interrupts''. The PCI bus has its own system of interrupts. But
since the PCI-aware BIOS sets up these PCI interrupts to map to IRQs,
it seemingly behaves just as described above. Except that sharing of
PCI interrupts is allowed (2 or more devices may use the same IRQ
number).
I/O addresses are not the same as memory addresses. When an I/O
addresses is put onto the computer's address bus, another wire is
energized. This both tells main memory to ignore the address and
tells all devices which have I/O addresses (such as the serial port)
to listen to the address sent on the bus to see if it matches the
device's. If the address matches, then the I/O device reads the data
on the data bus.
The I/O address of a certain device (such as ttyS2) will actually be a
range of addresses. The lower address in this range is the base
address. "address" usually means just the "base address".
[1m4.4. Names: ttyS0, ttyS1, etc.[0m
The serial ports are named ttyS0, ttyS1, etc. (and usually correspond
respectively to COM1, COM2, etc. in DOS/Windows). The /dev directory
has a special file for each port. Type "ls /dev/ttyS*" to see them.
Just because there may be (for example) a ttyS3 file, doesn't
necessarily mean that there exists a physical serial port there.
Which one of these names (ttyS0, ttyS1, etc.) refers to which physical
serial port is determined as follows. The serial driver (software)
maintains a table showing which I/O address corresponds to which ttyS.
This mapping of names (such as ttyS1) to I/O addresses (and IRQ's) may
be both set and viewed by the "setserial" command. See ``What is
Setserial''. This does not set the I/O address and IRQ in the
hardware itself (which is set by jumpers or by plug-and-play
software). Thus which physical port corresponds to say ttyS1 depends
both on what the serial driver thinks (per setserial) and what is set
in the hardware. If a mistake has been made, the physical port may
not correspond to any name (such as ttyS2) and thus it can't be used.
See ``Serial Port Devices /dev/ttyS2, etc.'' for more details>
[1m4.5. Interrupts[0m
Bytes come in over the phone line to the modem, are converted from
analog to digital by the modem and passed along to the serial port on
their way to their destination inside your computer. When the serial
port receives a number of bytes (may be set to 1, 4, 8, or 14) into
its FIFO buffer, it signals the CPU to fetch them by sending an
electrical signal known as an interrupt on a certain wire normally
used only by that port. Thus the FIFO waits until it has received a
number of bytes and then issues an interrupt.
However, this interrupt will also be sent if there is an unexpected
delay while waiting for the next byte to arrive (known as a timeout).
Thus if the bytes are being received slowly (such as from someone
typing on a terminal keyboard) there may be an interrupt issued for
every byte received. For some UART chips the rule is like this: If 4
bytes in a row could have been received in an interval of time, but
none of these 4 show up, then the port gives up waiting for more bytes
and issues an interrupt to fetch the bytes currently in the FIFO. Of
course, if the FIFO is empty, no interrupt will be issued.
Each interrupt conductor (inside the computer) has a number (IRQ) and
the serial port must know which conductor to use to signal on. For
example, ttyS0 normally uses IRQ number 4 known as IRQ4 (or IRQ 4). A
list of them and more will be found in "man setserial" (search for
"Configuring Serial Ports"). Interrupts are issued whenever the
serial port needs to get the CPU's attention. It's important to do
this in a timely manner since the buffer inside the serial port can
hold only 16 incoming bytes. If the CPU fails to remove such received
bytes promptly, then there will not be any space left for any more
incoming bytes and the small buffer may overflow (overrun) resulting
in a loss of data bytes.
For an external modem, there may be no way (such as flow control) to
stop the flow rapidly enough to prevent such an overrun. For an
internal modem, the 16-byte FIFO buffer is on the same card and most
modems will not write to it if it's full. Thus it will not overrun
the 16-byte buffers but it may need to use ``Modem-to-Modem Flow
Control'' to prevent the modem itself from being overrun. This is one
advantage of internal modems over an external.
Interrupts are also issued when the serial port has just sent out all
of its bytes from its small transmit FIFO buffer out the external
cable. It then has space for 16 more outgoing bytes. The interrupt
is to notify the CPU of that fact so that it may put more bytes in the
small transmit buffer to be transmitted. Also, when a modem control
line changes state, an interrupt is issued.
The buffers mentioned above are all hardware buffers. The serial port
also has large buffers in main memory. This will be explained later
Interrupts convey a lot of information but only indirectly. The
interrupt itself just tells a chip called the interrupt controller
that a certain serial port needs attention. The interrupt controller
then signals the CPU. The CPU then runs a special program to service
the serial port. That program is called an interrupt service routine
(part of the serial driver software). It tries to find out what has
happened at the serial port and then deals with the problem such a
transferring bytes from (or to) the serial port's hardware buffer.
This program can easily find out what has happened since the serial
port has registers at IO addresses known to the the serial driver
software. These registers contain status information about the serial
port. The software reads these registers and by inspecting the
contents, finds out what has happened and takes appropriate action.
[1m4.6. Data Compression (by the Modem)[0m
Before continuing with the basics of the serial port, one needs to
understand about something done by the modem: data compression. In
some cases this task is actually done by software run on the
computer's CPU but unfortunately at present, such software only works
for MS Windows. The discussion here will be for the case where the
modem itself does the compression since this is what must happen in
order for the modem to work under Linux.
In order to send data faster over the phone line, one may compress
(encode it) using a custom encoding scheme which itself depends on the
data. The encoded data is smaller than the original (less bytes) and
can be sent over the Internet in less time. This process is called
"data compression".
If you download files from the Internet, they are likely already
compressed and it is not feasible for the modem to try to compress
them further. Your modem may sense that what is passing thru has
already been compressed and refrain from trying a compress it any
more. If you are receiving data which has been compressed by the
other modem, your modem will decompress it and create many more bytes
than were sent over the phone line. Thus the flow of data from your
modem into your computer will be higher than the flow over the phone
line to you. The ratio of this flow is called the compression ratio.
Compression ratios as high as 4 are possible, but not very likely.
[1m4.7. Error Correction[0m
Similar to data compression, modems may be set to do error correction.
While there is some overhead cost involved which slows down the
byte/sec flow rate, the fact that error correction strips off start
and stop bits actually increases the data byte/sec flow rate.
For the serial port's interface with the external world, each 8-bit
byte has 2 extra bits added to it: a start-bit and a stop-bit.
Without error correction, these extra start and stop bits usually go
right thru the modem and out over the phone lines. But when error
correction is enabled, these extra bits are stripped off and the 8-bit
bytes are put into packets. This is more efficient and results in
higher byte/sec flow in spite of the fact that there are a few more
bytes added for packet headers and error correction purposes.
[1m4.8. Data Flow (Speeds)[0m
Data (bytes representing letters, pictures, etc.) flows from your
computer to your modem and then out on the telephone line (and
conversely). Flow rates (such as 56k (56000) bits/sec) are
(incorrectly) called "speed". But almost everyone says "speed"
instead of "flow rate". If there were no data compression the flow
rate from the computer to the modem would be about the same as the
flow rate over the telephone line.
Actually there are two different speeds to consider at your end of the
phone line:
· The speed on the phone line itself (DCE speed) modem-to-modem
· The speed from your computer's serial port to your modem (DTE
speed)
When you dial out and connect to another modem on the other end of the
phone line, your modem often sends you a message like "CONNECT 28800"
or "CONNECT 115200". What do these mean? Well, its either the DCE
speed or the DTE speed. If it's higher than the advertised modem speed
it must be the DTE modem-to-computer speed. This is the case for the
115200 speed shown above. The 28800 must be a DCE (modem-to-modem)
speed since the serial port has no such speed. One may configure the
modem to report either speed. Some modems report both speeds and
report the modem-to-modem speed as (for example): CARRIER 28800.
If you have an internal modem you would not expect that there would be
any speed limit on the DTE speed from your modem to your computer
since you modem is inside your computer and is almost part of your
computer. But there usually is since the modem contains a dedicated
serial port within it. On some software modems there is no such speed
limit.
It's important to understand that the average speed is often less than
the specified speed, especially on the short DTE computer-to-modem
line. Waits (or idle time) result in a lower average speed. These
waits may include long waits of perhaps a second due to ``Flow
Control''. At the other extreme there may be very short waits (idle
time) of several micro-seconds separating the end of one byte and the
start of the next byte. In addition, modems will fallback to lower
speeds if the telephone line conditions are less than pristine.
For a discussion of what DTE speed is best to use see section ``What
Speed Should I Use''.
[1m4.9. Flow Control[0m
Flow control means the ability to slow down the flow of bytes in a
wire. For serial ports this means the ability to stop and then
restart the flow without any loss of bytes. Flow control is needed
for modems and other hardware to allow a jump in instantaneous flow
rates.
[1m4.9.1. Example of Flow Control[0m
For example, consider the case where you connect a 33.6k external
modem via a short cable to your serial port. The modem sends and
receives bytes over the phone line at 33.6k bits per second (bps).
Assume it's not doing any data compression or error correction. You
have set the serial port speed to 115,200 bits/sec (bps), and you are
sending data from your computer to the phone line. Then the flow from
the your computer to your modem over the short cable is at 115.2k bps.
However the flow from your modem out the phone line is only 33.6k bps.
Since a faster flow (115.2k) is going into your modem than is coming
out of it, the modem is storing the excess flow (115.2k -33.6k = 81.6k
bps) in one of its buffers. This buffer would soon overrun (run out
of free storage space) unless the high 115.2k flow is stopped.
But now flow control comes to the rescue. When the modem's buffer is
almost full, the modem sends a stop signal to the serial port. The
serial port passes on the stop signal on to the device driver and the
115.2k bps flow is halted. Then the modem continues to send out data
at 33.6k bps drawing on the data it previous accumulated in its
buffer. Since nothing is coming into this buffer, the number of bytes
in it starts to drop. When almost no bytes are left in the buffer,
the modem sends a start signal to the serial port and the 115.2k flow
from the computer to the modem resumes. In effect, flow control
creates an average flow rate in the short cable (in this case 33.6k)
which is significantly less than the "on" flow rate of 115.2k bps.
This is "start-stop" flow control.
In the above simple example it was assumed that the modem did no data
compression. This could happen when the modem is sending a file which
is already compressed and can't be compressed further. Now let's
consider the opposite extreme where the modem is compressing the data
with a high compression ratio. In such a case the modem might need an
input flow rate of say 115.2k bps to provide an output (to the phone
line) of 33.6k bps (compressed data). This compression ratio is 3.43
(115.2/33.6). In this case the modem is able to compress the 115.2
bps PC-to-modem flow and send the same data (in compressed form) out
the phone line at 33.6bps. There's no need for flow control here so
long as the compression ratio remains higher than 3.43. But the
compression ratio varies from second to second and if it should drop
below 3.43, flow control will be needed
In the above example, the modem was an external modem. But the same
situation exists (as of early 2003) for most internal modems. There
is still a speed limit on the PC-to-modem speed even though this flow
doesn't take place over an external cable. This makes the internal
modems compatible with the external modems.
In the above example of flow control, the flow was from the computer
to a modem. But there is also flow control which is used for the
opposite direction of flow: from a modem (or other device) to a
computer. Each direction of flow involves 3 buffers: 1. in the modem
2. in the UART chip (called FIFOs) and 3. in main memory managed by
the serial driver. Flow control protects all buffers (except the
FIFOs) from overflowing.
Under Linux, the small UART FIFO buffers are not protected by flow
control but instead rely on a fast response to the interrupts they
issue. Some UART chips can be set to do hardware flow control to
protect their FIFOs but Linux (as of early 2003) doesn't seem to
support it. FIFO stand for "First In, First Out" which is the way it
handles bytes in a queue. All the 3 buffers use the FIFO rule but
only the one in the UART is named "FIFO". This is the essence of
flow control but there are still some more details.
If you have set the highest PC-to-modem speed, you may not need flow
control in the direction from the modem to a PC. For a complex
example of a case where it's needed see "Complex Flow Control Example"
in the Serial-HOWTO. To slow down this incoming flow, your modem must
tell the other modem to stop sending. See ``'' name="Modem-to-Modem
Flow Control">.
[1m4.9.2. Hardware vs. Software Flow Control[0m
If feasible, it's best to use "hardware" flow control that uses two
dedicated "modem control" wires to send the "stop" and "start"
signals. Hardware flow control at the serial port works like this:
The two pins, RTS (Request to send) and CTS (Clear to send) are used.
When the computer is ready to receive date it asserts RTS by putting a
positive voltage on the RTS pin (meaning "Request To Send to me").
When the computer is not able to receive any more bytes, it negates
RTS by putting a negative voltage on the pin saying: "stop sending to
me". The RTS pin is connected by the serial cable to another pin on
the modem, printer, terminal, etc. This other pin's only function is
to receive this signal.
For the case of a modem, this "other" pin will be the modem's RTS pin.
But for a printer, another PC, or a non-modem device, it's usually a
CTS pin so a "crossover" or "null modem" cable is required. This
cable connects the CTS pin at one end with the RTS pin at the other
end (two wires since each end of the cable has a CTS pin). For a
modem, a straight-thru cable is used.
For the opposite direction of flow a similar scheme is used. For a
modem, the CTS pin is used to send the flow control signal to the CTS
pin on the PC. For a non-modem, the RTS pin sends the signal. Thus
modems and non-modems have the roles of their RTS and CTS pins
interchanged. Some non-modems such as dumb terminals may use other
pins for flow control such as the DTR pin instead of RTS.
Software flow control uses the main receive and transmit data wires to
send the start and stop signals. It uses the ASCII control characters
DC1 (start) and DC3 (stop) for this purpose. They are just inserted
into the regular stream of data. Software flow control is not only
slower in reacting but also does not allow the sending of binary data
unless special precautions are taken. Since binary data will likely
contain DC1 and DC3 characters, special means must be taken to
distinguish between a DC3 that means a flow control stop and a DC3
that is part of the binary code. Likewise for DC1. To get software
flow control to work for binary data requires both modem (hardware)
and software support.
[1m4.9.3. Symptoms of No Flow Control[0m
Understanding flow-control theory can be of practical use. For
example I used my modem to access the Internet and it seemed to work
fine. But after a few months, I tried to send out long files from my
PC and a huge amount of retries and errors resulted but it finally
succeeded. Receiving in the other direction (from my ISP to me)
worked fine. The problem turned out to be a modem with flow control
disabled. My modem's buffer was overflowing (overrunning) on long
outgoing files since no "stop" signal was ever sent to my computer to
halt sending to the modem. There was no problem in the direction from
the modem to my computer since the capacity (say 115.2 kbps) of the
serial port was always higher than the flow from the telephone line.
But it was a problem in the other direction where the PC would send at
115.2 kbps and the modem couldn't handle this high flow resulting in
overruns of the modem's buffer. The fix was to enable flow control by
putting into the modem's init string an enable-flow-control command.
[1m4.9.4. Modem-to-Modem Flow Control[0m
This is the flow control of the data sent over the telephone lines
between two modems. It works as long as error correction is enabled.
Actually, even without error correction it's possible to enable
software flow control between modems but it may interfere with sending
binary data so it's not often used.
[1m4.10. Data Flow Path; Buffers[0m
It's been mentioned that there are 3 buffers for each direction of
flow (3 pairs altogether): 16-byte FIFO buffers (in the UART), a pair
of larger buffers inside a device connected to the serial port (such
as a modem), and a pair of buffers (say 8k) in main memory. When an
application program sends bytes to the serial port they first get
stashed in the transmit serial port buffer in main memory. The other
member of this pair consists of a receive buffer for the opposite
direction of byte-flow. Here's an example diagram for the case of
browsing the Internet with a browser. Transmit data flow is left to
right while receive flow is right to left. There is a separate buffer
for each direction of flow.
application 8k-byte 16-byte 1k-byte tele-
BROWSER ------- MEMORY -------- FIFO --------- MODEM -------- phone
program buffer buffer buffer line
For the transmit case, the serial device driver takes out say 15 bytes
from this transmit buffer (in main memory), one byte at a time and
puts them into the 16-byte transmit buffer in the serial UART for
transmission. Once in that transmit buffer, there is no way to stop
them from being transmitted. They are then transmitted to the modem
or (other device connected to the serial port) which also has a fair
sized (say 1k) buffer. When the device driver (on orders from flow
control sent from the modem) stops the flow of outgoing bytes from the
computer, what it actually stops is the flow of outgoing bytes from
the large transmit buffer in main memory. Even after this has
happened and the flow to the modem has stopped, an application program
may keep sending bytes to the 8k transmit buffer until it becomes
fill. At the same time, the bytes stored in the FIFO and continue to
be sent out. Bytes stored in the modem will continue to be sent out
the phone line unless the modem has gotten a modem-to-modem flow
control stop from the modem at the other end of the phone line.
When the memory buffer gets fill, the application program can't send
any more bytes to it (a "write" statement in a C-program blocks) and
the application program temporarily stops running and waits until some
buffer space becomes available. Thus a flow control "stop" is
ultimately able to stop the program that is sending the bytes. Even
though this program stops, the computer does not necessarily stop
computing since it may switch to running other processes while it's
waiting at a flow control stop.
The above was a little oversimplified in three ways. First, some
UARTs can do automatic hardware flow control which can stop the
transmission out of the FIFO buffers if needed (not yet supported by
Linux). Second, while an application process is waiting to write to
the transmit buffer, it could possibly perform other tasks. Third,
the serial driver (located between the memory buffer and the FIFO) has
it's own small buffer (in main memory) used to process characters.
[1m4.11. Modem Commands[0m
Commands to the modem are sent to it from the communication software
over the same conductor as used to send data. The commands are short
ASCII strings. Examples are "AT&K3" for enabling hardware flow
control (RTS/CTS) between your computer and modem; and "ATDT5393401
for Dialing the number 5393401. Note all commands are prefaced by
"AT". Some commands such as enabling flow control help configure the
modem. Other commands such as dialing a number actually do something.
There are about a hundred or so different possible commands. When
your communication software starts running, it first sends an "init"
string of commands to the modem to configure it. All commands are
sent on the ordinary data line before the modem dials (or receives a
call).
Once the modem is connected to another modem (on-line mode),
everything that is sent from your computer to your modem goes directly
to the other modem and is not interpreted by the modem as a command.
There is a way to "escape" from this mode of operation and go back to
command mode where everything sent to the modem will be interpreted as
a command. The computer just sends "+++" with a specified time
spacing before and after it. If this time spacing is correct, the
modem reverts to command mode. Another way to do this is by a signal
on a certain modem control line.
There are a number of lists of modem commands on the Internet. The
section ``Web Sites'' has links to a couple of such web-sites.
Different models and brands of modems do not use exactly the same set
of such commands. So what works for one modem might not work for
another. Some common commands (not guaranteed to work on all modems)
are listed in this HOWTO in the section ``Modem Configuration''
[1m4.12. Serial Driver Module[0m
The device driver for the serial port is the software that operates
the serial port. It is now provided as a serial module. From kernel
2.2 on, this module will normally get loaded automatically if it's
needed. In earlier kernels, you had to have kerneld running in order
to do auto-load modules on demand. Otherwise the serial module needed
to be explicitly listed in /etc/modules. Before modules became
popular with Linux, the serial driver was usually built into the
kernel (and sometimes still is). If it's built-in don't let the
serial module load or else you will have two serial drivers running at
the same time. With 2 drivers there are all sorts of errors including
a possible "I/O error" when attempting to open a serial port. Use
"lsmod" to see if the module is loaded.
When the serial module is loaded it displays a message on the screen
about the existing serial ports (often showing a wrong IRQ). But once
the module is used by setserial to tell the device driver the
(hopefully) correct IRQ then you should see a second display similar
to the first but with the correct IRQ, etc. See "Serial Module" in
the Serial-HOWTO. See ``What is Setserial'' for more info on
setserial.
[1m5. Configuring Overview[0m
Since each modem has an associated serial port and the port has both
hardware and software, there are three parts to configuring a modem:
· Locate the serial port hardware: IO address, IRQ; Done by PnP
methods or jumpers, setserial. See ``Locating the Serial Port: IO
address IRQs'' ``What is Setserial''
· Configure the serial port driver (high-level): Done by the
communication program (stty-like). Sets speed, flow control, etc.
See ``Configuring the Serial Driver (high-level)'' See ``What is
stty ?''
· Configure the modem itself: Done by the communication program See
``Modem Configuration''
The above omits a few other things that "setserial" can do besides
locating the serial ports. But normally you don't need to use them.
Setserial may be used in the future to enable super-high speed.
Communication programs include minicom, seyon, or wvdial (for PPP) and
mgetty for dial-in. Such communication programs require that you
configure them, although the default configuration they come with may
only need a little tweaking.
Unfortunately the communication program doesn't locate the serial
port. This "locating" is the low-level PnP configuring of the serial
port: setting its IO address and IRQ in both the hardware and the
driver. If you are lucky, this will happen automatically when you
boot Linux. Setting these in the hardware was formerly done by
jumpers and then running "setserial" but today it's done by "Plug-and-
Play" software. You may still need "setserial". So if Linux (or the
wvdial program, etc.) doesn't report what serial port your modem is
on, then you can try to find it yourself per the next section but it
may not be easy.
[1m6. Locating the Serial Port: IO address, IRQs[0m
[1m6.1. What Bus is my Serial Port On?[0m
If you need to find a serial port it often helps if you know what bus
it's on. If the serial port is on a card, you may know what bus the
card inserts into (usually a PCI slot). But if the serial port is
built into the motherboard it may not be clear what bus it's on. For
old motherboards that have ISA bus slots, it's likely on the ISA bus
and may not even be Plug-and-Play. But even if all your slots are
PCI, the serial port is likely to be on either the ISA bus or LPC bus
(also called a "LPC interface"). LPC is common on laptop computers.
Type "lspci" to see if it shows "LPC". Unfortunately, the LPC bus has
no standard Plug-and-Play method for low-level configuring devices on
it. One way to deal with it is to hope that the BIOS can configure
them using ACPI. Some Linux developers are aware of the problem (in
late 2004) and Linux may support the LPC bus better in the future. To
see if you have a LCP bus, type "lspci" and look for a LPC bridge.
[1m6.2. IO & IRQ Overview[0m
For a serial port to work properly it first must be given both an IO
address and an IRQ. For old hardware (of mid 1990s), jumpers on a
card or the a saved BIOS setting does it. For newer hardware the BIOS
or Linux must set them at boot-time, and the new hardware doesn't
remember how it was set once it's powered Enabling hardware it gives
it both an IRQ and an IO address. Without an IO address, it can't be
used. Without an IRQ it will need to use inefficient polling methods
for which one must set the IRQ to 0 in the serial driver. In olden
days IRQs and IO addresses were set by jumpers or switches on a serial
port card. Today these are set by digital signals sent to the
hardware by the BIOS or Linux. It all should get configured
automatically (provided the BIOS has not been previously set up to
disable it) so that you only need to read this if you're having
problems or if you want to understand how it works.
The driver must of course know both the IO address and IRQ so that it
can talk to the serial port chip. Modern serial port drivers (kernel
2.4) try to determine this by PnP methods so one doesn't normally need
to tell the driver (by using "setserial"). A driver may also set an
IO address or IRQ in the hardware. But unfortunately, there is some
PCI serial port hardware that the driver doesn't recognize so you
might need to enable the port yourself. See ``PCI: Enabling a
disabled port''
For the old ISA bus, the driver also probes likely serial port
addresses to see if there are any serial ports there. This works for
the case of jumpers and sometimes works for a ISA PnP port when the
driver doesn't do ISA PnP (prior to kernel 2.4).
Locating the serial port by giving it an IRQ and IO address is low-
level configuring. It's often automatically done by the serial driver
but sometimes you have to do it yourself. What follows repeats what
was said above but in more detail.
The low-level configuring consists of assigning an IO address, IRQ,
and names (such as ttyS2 = tts/2). This IO-IRQ pair must be set in
both the hardware and told to the serial driver. And the driver needs
to call this pair a name (such as ttyS2). We could call this "io-irq"
configuring for short. The "setserial" program is one way to tell the
driver. The other way is for the driver to use PnP methods to
detect/set the IO/IRQ and then remember what it did. For jumpers,
there is no PnP but the driver might detect the port if the jumpers
are set to the usual I0/IRQ. If you need to configure but don't
understand certain details it's easy to get into trouble.
When Linux starts, an effort is made to detect and configure (low-
level) the serial ports. Exactly what happens depends on your BIOS,
hardware, Linux distribution, kernel version, etc. If the serial
ports work OK, there may be no need for you to do any more low-level
configuring.
If you're having problems with the serial ports, then you may need to
do low-level configuring. If you have kernel 2.2 or lower, then you
need to do it if you:
· Plan to use more than 2 ISA serial ports
· Are installing a new serial port (such as an internal modem)
· One or more of your serial ports have non-standard IRQs or IO
addresses
Starting with kernel 2.2 you may be able to use more that 2 serial
ports without doing any low-level configuring by sharing interrupts.
All PCI ports should support this but for ISA, it only works for some
hardware. It may be just as easy to give each port a unique interrupt
if they is available. See ``Interrupt sharing and Kernels 2.2+''
The low-level configuring (setting the IRQ and IO address) seems to
cause people more trouble than the high-level stuff, although for many
it's fully automatic and there is no configuring to be done. Until
the port in enabled and the serial driver knows the correct IRQ and IO
address, the port will not usually not work at all.
A port may be disabled, either by the BIOS or by failure of Linux to
find and enable the port. For modern ports (provided the BIOS hasn't
disabled them) manual PnP tools such as lspci should be able to find
them. Applications, and utilities such as "setserial" and "scanport"
(Debian only ??) only probe I0 addresses, don't use PnP tools, and
thus can't detect disabled ports.
Even if an ISA port can be found by the probing done by the serial
driver it may work extremely slow if the IRQ is wrong. See
``Extremely Slow: Text appears on the screen slowly after long
delays''. PCI ports are less likely to get the IRQ wrong.
IO address, IRQs, etc. are called "resources" and we are thus
configuring certain resources. But there are many other types of
"resources" so the term has many other meanings. In summary, the low-
level configuring consists of enabling the device, giving it a name
(ttyS2 for example) and putting two values (an IRQ number and IO
address) into two places:
1. The device driver (done by PnP or "setserial")
2. Configuration registers of the serial port hardware itself, done by
PnP software (or jumpers on legacy hardware).
You may watch the start-up (= boot-time) messages. They are usually
correct. But if you're having problems, your serial port may not show
up at all or if you do see a message from "setserial" it may not show
the true configuration of the hardware (and it is not necessarily
supposed to). See ``I/O Address & IRQ: Boot-time messages''.
[1m6.3. PCI Bus Support[0m
[1m6.3.1. Introduction[0m
Although some PCI modems are "winmodems" without a Linux driver (and
will not work under Linux), other PCI modems will often work OK under
Linux. If it's a software modem, then you need to find a driver for
it since support for "winmodems" is not built into their serial
driver. See Linmodem-HOWTO.
If you have kernel 2.4 or better, then there should be support for PnP
for both the PCI and ISA buses (either built-in or by modules). Some
PCI serial ports can be automatically detected and low-level
configured by the serial driver. Others may not be.
While kernel 2.2 supported PCI in general, it had no support for PCI
serial ports (although some people got them working anyway). Starting
with kernel 2.4, the serial driver will read the id number digitally
stored in the serial hardware to determine how to support it (if it
knows how). It should assign an I/O address to it, determine it's
IRQ, etc. So you don't need to use "setserial" for it.
There is a possible problem if you don't use the device filesystem.
The driver may assign the port to say "ttyS04" per a boot-time message
(use dmesg to see it). But if you don't have a "file" dev/ttyS4 then
the port will not work. So you will then need to create it, using
cd /dev and then ./MAKEDEV ttyS4
For the device filesystem, the driver should create the device tts/1
[1m6.3.2. More info on PCI[0m
PCI ports are not well standardized. Some use main memory for
communication with the PC. Some require special enabling of the IRQ.
The output of "lspci -vv" can help determine if one can be supported.
If you see a 4-digit IO port, the port might work by just telling
"setserial" the IO port and the IRQ. Some people have gotten a 3COM
3CP5610 PCI Modem to work that way.For example, if lspci shows IRQ 10,
I/O at 0xecb8 and you decide to name it ttyS2 then the command is:
setserial /dev/ttyS2 irq 10 port 0xecb8 autoconfig
Note that the boot-time message "Probing PCI hardware" means reading
the PnP configuration registers in the PCI devices which detects info
about all PCI cards and on-board PCI devices This is different that
the probing of IO addresses by the serial driver which means reading
certain IO addresses to see if what's read looks like there's a serial
port at that address.
[1m6.4. Common mistakes made re low-level configuring[0m
Here are some common mistakes people make:
· setserial command: They run it (without the "autoconfig" and
auto_irq options) and think it has checked the hardware to see if
what it shows is correct (it hasn't).
· setserial messages: They see them displayed on the screen at boot-
time (or by giving the setserial command) and erroneously think
that the result always shows how their hardware is actually
configured.
· /proc/interrupts: When their serial device isn't in use they don't
see its interrupt there, and erroneously conclude that their serial
port can't be found (or doesn't have an interrupt set).
· /proc/ioports and /proc/tty/driver/serial: People think this shows
the actual hardware configuration when it only shows about the same
info (possibly erroneous) as setserial.
[1m6.5. IRQ & IO Address Must be Correct[0m
There are really two answers to the question "What is my IO and IRQ?"
1. What the device driver thinks has been set (This is what setserial
usually sets and shows.). 2. What is actually set in the hardware.
Both 1. and 2. above should be the same. If they're not it spells
trouble since the driver has incorrect info on the physical serial
port. In some cases the hardware is disabled so it has no IO address
or IRQ.
If the driver has the wrong IO address it will try to send data to a
non-existing serial port --or even worse, to some other device. If it
has the wrong IRQ the driver will not get interrupt service requests
from the serial port, resulting in a very slow or no response. See
``Extremely Slow: Text appears on the screen slowly after long
delays''. If it has the wrong model of UART there is also apt to be
trouble. To determine if both I0-IRQ pairs are identical you must
find out how they are set in both the driver and the hardware.
[1m6.6. What is the IO Address and IRQ per the driver ?[0m
[1m6.6.1. Introduction[0m
What the driver thinks is not necessarily how the hardware is actually
set. If everything works OK then what the driver thinks is likely
correct (set in the hardware) and you don't need to investigate
(unless you're curious or want to become a guru). Ways to determine
what the driver thinks include: boot-time messages ``I/O Address &
IRQ: Boot-time messages'', the /proc directory "files" ``The /proc
directory and setserial'', and the "setserial" command.
[1m6.6.2. I/O Address & IRQ: Boot-time messages[0m
In many cases your ports will automatically get low-level configured
at boot-time (but not always correctly). To see what is happening,
look at the start-up messages on the screen. Don't neglect to check
the messages from the BIOS before Linux is loaded (no examples shown
here). These BIOS messages may be frozen by pressing the Pause key
(while holding down shift). It's often tricky to freeze them and you
may need to hit Ctrl-Alt-Del while Linux is booting to start rebooting
and try again. What these messages display may change as booting
progresses and it's often tricky to freeze it at exactly the right
words.
Use Shift-PageUp to scroll back to the messages after they have
flashed by. Shift-PageDown will scroll in the opposite direction.
The dmesg command (or looking at logs in /var/log) will show only the
first of these two messages. Here's an example of the start-up
messages (as of 2004, almost the same as for 1999). Note that ttyS00
is the same as /dev/ttyS0, etc.
At first you see what was detected (but the irq is only a wild guess):
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
ttyS02 at 0x03e8 (irq = 4) is a 16550A
ttyS04 at port 0xeff0 (irq = 10) is a 16550A
Note that ttyS0-ttyS2 were detected by probing the standard addresses
while ttyS4 is a PCI port detected by probing the PCI configuration.
Later setserial shows you what was saved in a configuration file
(which you may edit), but it's not necessarily correct either:
Loading the saved-state of the serial devices...
/dev/ttyS1 at 0x02f8 (irq = 3) is a 16550A
/dev/ttyS2 at 0x03e8 (irq = 5) is a 16550A
Note that the configuration file only had ttyS1-2 in it so that ttyS0
and ttyS4 were not affected by it. There is also a slight
discrepancy: The first message shows ttyS2 at irq=4 while the second
shows it at irq=5. In most cases the second message is the correct
one. But if you're having trouble, it may be misleading. Before
reading the explanation of all of this complexity in the rest of this
section, you might just try using your serial port and see if it works
OK. If so it may not be essential to read further.
The second message is from the setserial program being run at boot-
time from a script in the /etc directory tree. It shows what the
device driver thinks is the correct configuration. But this too could
be wrong. For example, the irq could actually be set to irq=8 in the
hardware (both messages wrong). The irq=5 could be there because the
configuration file is incorrect.
With old jumper-set serial ports Linux sometimes gets IRQs wrong
because it doesn't by default probe for IRQs. It just assumes the
"standard" ones (first message) or accepts what is in a configuration
file (second message). Neither of these is necessarily correct. If
the serial driver has the wrong IRQ, the serial port is very slow or
doesn't seem to work at all.
The first message is a result of Linux probing the ISA serial port
addresses but it doesn't probe for IRQs. If a port shows up here it
exists but the IRQ may be wrong. Linux doesn't check IRQs because
doing so is not foolproof. It just assumes the IRQs are as shown
because they are the "standard" values. Your may check them manually
with setserial using the autoconfig and auto_irq options but this
isn't guaranteed to be correct either.
The data shown by the BIOS messages (which you see at first before
Linux is booted) is what is initially set in the hardware. If your
serial port is Plug-and-Play (PnP) then it's possible that "isapnp" or
"setpci" will run and change these settings. Look for messages about
this after Linux starts. The last serial port message shown in the
example above should agree with the BIOS messages (as possibly
modified by isapnp or setpci). If they don't agree then you either
need to change the setting in the port hardware or use setserial to
tell the driver what is actually set in the hardware.
Also, if you have Plug-and-Play (PnP) serial ports, they can only be
found by PnP software unless the IRQ and IO has been set inside the
hardware by Plug-and-Play software. Prior to kernel 2.4 this was a
common reason why the start-up messages did not show a serial port
that physically exists. A PnP BIOS may automatically low-level
configure them. PnP configuring will be explained later.
[1m6.6.3. The /proc directory and setserial[0m
Type "setserial -g /dev/ttyS*". There are some other ways to find
this info by looking at "files" in the /proc directory. Be warned
that there is no guarantee that the same is set in the hardware.
/proc/ioports will show the IO addresses that the drivers are using.
/proc/interrupts shows the IRQs that are used by drivers of currently
running processes (that have devices open). It shows how many
interrupts have actually be issued. /proc/tty/driver/serial shows
much of the above, plus the number of bytes that have been received
and sent (even if the device is not now open).
Note that for the IO addresses and IRQ assignments, you are only
seeing what the driver thinks and not necessarily what is actually set
in the hardware. The data on the actual number of interrupts issued
and bytes processed is real however. If you see a large number of
interrupts and/or bytes then it probably means that the device is (or
was) working. But the interrupts might be from another device. If
there are no bytes received (rx:0) but bytes were transmitted (tx:3749
for example), then only one direction of flow is working (or being
utilized).
Sometimes a showing of just a few interrupts doesn't mean that the
interrupt is actually being physically generated by any serial port.
Thus if you see almost no interrupts for a port that you're trying to
use, that interrupt might not be set in the hardware. To view
/proc/interrupts to check on a program that you're currently running
(such as "minicom") you need to keep the program running while you
view it.
[1m6.7. What is the IO Address & IRQ of my Serial Port Hardware?[0m
[1m6.7.1. Introduction[0m
If it's PCI or ISA PnP then what's set in the hardware has been done
by PnP methods. Even if nothing has been set or the port disabled,
PnP ports may still be found by using "lspci -v" or "isapnp
--dumpregs". Ports disabled by jumpers (or hardware failures) are
completely lost. See ``ISA PnP ports'', ``PCI: What IOs and IRQs have
been set?'', ``PCI: Enabling a disabled port''
PnP ports don't store their configuration in the hardware when the
power is turned off. This is in contrast to Jumpers (non-PnP) which
remain the same with the power off. That's why a PnP port is more
likely to be found in a disabled state than an old non-PnP one.
[1m6.7.2. PCI: What IOs and IRQs have been set?[0m
For PCI, the BIOS almost always sets the IRQ and may set the IO
address as well. To see how it's set use "lspci -vv" (best) or look
in /proc/bus/pci (or for kernels <2.2 /proc/pci). The modem's serial
port is often called a "Communication controller". Look for this. If
lspci shows "I/O ports at ... [disabled]" then the serial port is
disabled and the hardware has no IO address so it's lost and can't be
used. See ``PCI: Enabling a disabled port'' for how to enable it.
If more than one IO address is shown, the first one is more likely to
be it. You can't change the IRQ (at least not with "setpci") This
is because if one writes an IRQ it it's hardware register no action is
taken on it. It's the BIOS that should actually set up the IRQs and
then write the correct value to this register for lspci to view. If
you must, change the IO address with "setpci" by changing the
BASE_ADDRESS_0 or the like.
[1m6.7.3. PCI: Enabling a disabled port[0m
If the port communicates via an IO address then "lspci -vv" should
show "Control: I/O+ ..." with + meaning that the IO address is
enabled. If it shows "I/O-" (and "I/O ports at ... [disabled]") then
you may need to use the setpci command to enable it. For example
"setpci -d 151f:000 command=101". 151f is the vendor id, and 000 is
the device id both obtained from "lspci -n -v" or from /proc/bus/pci
or from "scanpci -v". The "command=101" means that 101 is put into
the command register which is the same as the "Control" register
displayed by "lspci". The 101h sets two bits: the 1 sets I/O to + and
the 100 part keeps SERR# set to +. In this case only the SERR# bit
of the Control register was initially observed to be + when the lspci
command was run. So we kept it enabled to + by setting bit 8 (where
bit 0 is I/O) to 1 by the first 1 in 101. Some serial cards don't use
SERR# so if you see SERR#- then there's no need to enable it so then
use: command=1. Then you'll need to set up "setserial" to tell the
driver the IO and IRQ.
Bit 8 is actually the 9th bit since we started counting bits from 0.
Don't be alarmed that lspci shows a lot of - signs showing that the
card doesn't have many features available (or enabled). Serial ports
are relatively slow and don't need these features.
Another way to enable it is to let the BIOS do it by telling the BIOS
that you don't have a plug-and-play operating system. Then the BIOS
should enable it when you start your PC. If you have MS Windows9x on
the same PC then doing this might cause problems with Windows (see
Plug-and-Play-HOWTO).
[1m6.7.4. ISA PnP ports[0m
For an ISA Plug-and-Play (PnP) port one may try the pnpdump program
(part of isapnptools). If you use the --dumpregs option then it
should tell you the actual IO address and IRQ set in the port. It
should also find an ISA PnP port that is disabled. The address it
"trys" is not the device's IO address, but a special address used for
communicating with PnP cards.
[1m6.7.5. Finding a port that is not disabled (ISA, PCI, PnP, non-PnP)[0m
Perhaps the BIOS messages will tell you some info before Linux starts
booting. Use the shift-PageUp key to step back thru the boot-time
messages and look at the very first ones which are from the BIOS.
This is how it was before Linux started. Setserial can't change it
but isapnp or setpci can. Starting with kernel 2.4, the serial driver
can make such changes for many (but not all) serial ports.
Using "scanport" (Debian only ??) will probe all I/O ports and will
indicate what it thinks may be serial port. After this you could try
probing with setserial using the "autoconfig" option. You'll need to
guess the addresses to probe at (using clues from "scanport"). See
``What is Setserial''.
For a port set with jumpers, the IO ports and IRQs are set per the
jumpers. If the port is not Plug-and-Play (PnP) but has been setup by
using a DOS program, then it's set at whatever the person who ran that
program set it to.
[1m6.7.6. Exploring via MS Windows (a last resort)[0m
For PnP ports, checking on how it's configured under DOS/Windows may
(or may not) imply how it's under Linux. MS Windows stores its
configuration info in its Registry which is not used by Linux so they
are not necessarily configured the same. If you let a PnP BIOS
automatically do the configuring when you start Linux (and have told
the BIOS that you don't have a PnP operating system when starting
Linux) then Linux should use whatever configuration is in the BIOS's
non-volatile memory. Windows also makes use of the same non-volatile
memory but doesn't necessarily configure it that way.
[1m6.8. Choosing Serial IRQs[0m
If you have Plug-and-Play ports then either a PnP BIOS or a serial
driver may configure all your devices for you so then you may not need
to choose any IRQs. PnP software determines what it thinks is best
and assigns them (but it's not always best). But if you directly use
isapnp (ISA bus) or jumpers then you have to choose. If you already
know what IRQ you want to use you could skip this section except that
you may want to know that IRQ 0 has a special use (see the following
paragraph).
[1m6.8.1. IRQ 0 is not an IRQ[0m
While IRQ 0 is actually the timer (in hardware) it has a special
meaning for setting a serial port with setserial. It tells the driver
that there is no interrupt for the port and the driver then will use
polling methods. Such polling puts more load on the CPU but can be
tried if there is an interrupt conflict or mis-set interrupt. The
advantage of assigning IRQ 0 is that you don't need to know what
interrupt is set in the hardware. It should be used only as a
temporary expedient until you are able to find a real interrupt to
use.
[1m6.8.2. Interrupt sharing, Kernels 2.2+[0m
Sharing of IRQs is where two devices use the same IRQ. As a general
rule, this wasn't allowed for the ISA bus. The PCI bus may share
IRQs but one can't share the same IRQ between the ISA and the PCI bus.
Most multi-port boards may share IRQs. Sharing is not as efficient
since every time a shared interrupt is given a check must be made to
determine where it came from. Thus if it's feasible, it's nicer to
allocate every device its own interrupt.
Prior to kernel 2.2, serial IRQs could not be shared with each other
except for most multiport boards. Starting with kernel 2.2 serial
IRQs may be sometimes shared between serial ports. In order for
sharing to work in 2.2 the kernel must have been compiled with
CONFIG_SERIAL_SHARE_IRQ, and the serial port hardware must support
sharing (so that if two serial cards put different voltages on the
same interrupt wire, only the voltage that means "this is an
interrupt" will prevail). Since the PCI bus specs permit sharing, any
PCI card should allow sharing.
[1m6.8.3. What IRQs to choose?[0m
The serial hardware often has only a limited number of IRQs. Also you
don't want IRQ conflicts. So there may not be much of a choice. Your
PC may normally come with ttyS0 and ttyS2 at IRQ 4, and ttyS1 and
ttyS3 at IRQ 3. Looking at /proc/interrupts will show which IRQs are
being used by programs currently running. You likely don't want to
use one of these. Before IRQ 5 was used for sound cards, it was often
used for a serial port.
Here is how Greg (original author of Serial-HOWTO) set his up in
/etc/rc.d/rc.serial. rc.serial is a file (shell script) which runs at
start-up (it may have a different name or location). For versions of
"setserial" after 2.15 it's not always done this way anymore but this
example does show the choice of IRQs.
/sbin/setserial /dev/ttyS0 irq 3 # my serial mouse
/sbin/setserial /dev/ttyS1 irq 4 # my Wyse dumb terminal
/sbin/setserial /dev/ttyS2 irq 5 # my Zoom modem
/sbin/setserial /dev/ttyS3 irq 9 # my USR modem
Standard IRQ assignments:
IRQ 0 Timer channel 0 (May mean "no interrupt". See below.)
IRQ 1 Keyboard
IRQ 2 Cascade for controller 2
IRQ 3 Serial port 2
IRQ 4 Serial port 1
IRQ 5 Parallel port 2, Sound card
IRQ 6 Floppy diskette
IRQ 7 Parallel port 1
IRQ 8 Real-time clock
IRQ 9 Redirected to IRQ2
IRQ 10 not assigned
IRQ 11 not assigned
IRQ 12 not assigned
IRQ 13 Math co-processor
IRQ 14 Hard disk controller 1
IRQ 15 Hard disk controller 2
There is really no Right Thing to do when choosing interrupts. Try to
find one that isn't being used by the motherboard, or any other
boards. 2, 3, 4, 5, 7, 10, 11, 12 or 15 are possible choices. Note
that IRQ 2 is the same as IRQ 9. You can call it either 2 or 9, the
serial driver is very understanding. If you have a very old serial
board it may not be able to use IRQs 8 and above.
Make sure you don't use IRQs 1, 6, 8, 13 or 14! These are used by
your motherboard. You will make her very unhappy by taking her IRQs.
When you are done you might want to double-check /proc/interrupts when
programs that use interrupts are being run and make sure there are no
conflicts.
[1m6.9. Choosing Addresses --Video card conflict with ttyS3[0m
Here's a problem with some old serial cards. The IO address of the
IBM 8514 video board (and others like it) is allegedly 0x?2e8 where ?
is 2, 4, 8, or 9. This may conflict with the IO address of ttyS3 at
0x02e8. Your may think that this shouldn't happen since the addresses
are different in the high order digit (the leading 0 in 02e8). You're
right, but a poorly designed serial port may ignore the high order
digit and respond to any address that ends in 2e8. That is bad news
if you try to use ttyS3 (ISA bus) at this IO address.
For the ISA bus you should try to use the default addresses shown
below. PCI cards use different addresses so as not to conflict with
ISA addresses. The addresses shown below represent the first address
of an 8-byte range. For example 3f8 is really the range 3f8-3ff.
Each serial device (as well as other types of devices that use IO
addresses) needs its own unique address range. There should be no
overlaps (conflicts). Here are the default addresses for commonly
used serial ports on the ISA bus:
ttyS0 address 0x3f8
ttyS1 address 0x2f8
ttyS2 address 0x3e8
ttyS3 address 0x2e8
Suppose there is an address conflict (as reported by setserial -g
/dev/ttyS*) between a real serial port and another port which does not
physically exist (and shows UART: unknown). Such a conflict shouldn't
cause problems but it sometimes does in older kernels. To avoid this
problem don't permit such address conflicts or delete /dev/ttySx if it
doesn't physically exist.
[1m6.10. Set IO Address & IRQ in the hardware (mostly for PnP)[0m
After it's set in the hardware don't forget to insure that it also
gets set in the driver by using setserial. For non-PnP serial ports
they are either set in hardware by jumpers or by running a DOS program
("jumperless") to set them (it may disable PnP). The rest of this
subsection is only for PnP serial ports. Here's a list of the
possible methods of configuring PnP serial ports:
· Using a PnP BIOS CMOS setup menu (usually only for external modems
on ttyS0 (Com1) and ttyS1 (Com2))
· Letting a PnP BIOS automatically configure a PnP serial port See
``Using a PnP BIOS to I0-IRQ Configure''
· Doing nothing if the serial driver recognized your card OK
· Using isapnp for a PnP serial port non-PCI)
· Using setpci (pciutils or pcitools) for the PCI bus
The IO address and IRQ must be set (by PnP) in their registers each
time the system is powered on since PnP hardware doesn't remember how
it was set when the power is shut off. A simple way to do this is to
let a PnP BIOS know that you don't have a PnP OS and the BIOS will
automatically do this each time you start. This might cause problems
in Windows (which is a PnP OS) if you start Windows with the BIOS
thinking that Windows is not a PnP OS. See Plug-and-Play-HOWTO.
Plug-and-Play (PnP) was designed to automate this io-irq configuring,
but for Linux it initially made life much more complicated. In modern
Linux (2.4 kernels --partially in 2.2 kernels), each device driver has
to do it's own PnP (using supplied software which it may utilize).
There is unfortunately no centralized planning for assigning IO
addresses and IRQs as there is in MS Windows. But it usually works
out OK in Linux anyway.
[1m6.10.1. Using a PnP BIOS to I0-IRQ Configure[0m
While the explanation of how to use setpci or isapnp for io-irq
configuring should come with such software, this is not the case if
you want to let a PnP BIOS do such configuring. Not all PnP BIOS can
do this. The BIOS usually has a CMOS menu for setting up the first
two serial ports. This menu may be hard to find. For an "Award" BIOS
it was found under "chipset features setup" There is often little to
choose from. For ISA serial ports, the first two ports normally get
set at the standard IO addresses and IRQs. See ``More on Serial Port
Names''
Whether you like it or not, when you start up a PC, a PnP BIOS starts
to do PnP (io-irq) configuring of hardware devices. It may do the job
partially and turn the rest over to a PnP OS (which Linux is in some
sense) or if thinks you don't have a PnP OS it may fully configure all
the PnP devices but not configure the device drivers.
If you tell the BIOS that you don't have a PnP OS, then the PnP BIOS
should do the configuring of all PnP serial ports --not just the first
two. An indirect way to control what the BIOS does (if you have
Windows 9x on the same PC) is to "force" a configuration under
Windows. See Plug-and-Play-HOWTO and search for "forced". It's
easier to use the CMOS BIOS menu which may override what you "forced"
under Windows. There could be a BIOS option that can set or disable
this "override" capability.
If you add a new PnP device, the BIOS should PnP configure it. It
could even change the io-irq of existing devices if required to avoid
any conflicts. For this purpose, it keeps a list of non-PnP devices
provided that you have told the BIOS how these non-PnP devices are io-
irq configured. One way to tell the BIOS this is by running a program
called ICU under DOS/Windows.
But how do you find out what the BIOS has done so that you set up the
device drivers with this info? The BIOS itself may provide some info,
either in its setup menus of via messages on the screen when you turn
on your computer. See ``What is set in my serial port hardware?''.
Other ways of finding out is to use lspci for the PCI bus or isapnp
--dumpregs for the ISA bus. The cryptic results it shows you may not
be clear to a novice.
[1m6.11. Giving the IRQ and IO Address to Setserial[0m
Once you've set the IRQ and IO address in the hardware (or arranged
for it to be done by PnP) you also need to insure that the "setserial"
command is run each time you start Linux. See the subsection ``Boot-
time Configuration''
[1m7. Configuring the Serial Driver (high-level) "stty"[0m
[1m7.1. Introduction[0m
This configuring is normally done by your communications program such
as wvdial. It may do much of it without even letting you know what
it's done. In olden days it was done with the "stty" utility. If you
set something manually with stty, the communications program may
change the setting to something else so it's usually best to just let
the communications program handle it. See ``What is stty ?''
[1m7.2. Hardware flow control (RTS/CTS)[0m
See ``Flow Control'' for an explanation of it. You should always use
hardware flow control if possible. Your communication program or
"getty" should have an option for setting it (and hopefully it's
enabled by default). It needs to be set both inside your modem (by an
init string or default) and in the device driver. Your communication
program should set both of these (if you configure it right).
If none of the above will fully enable hardware flow control. Then
you must do it yourself. For the modem, make sure that it's either
done by the init string or is on by default. If you need to tell the
device driver to do it is best done on startup by putting it in a file
that runs at boot-time. See the subsection ``Boot-time
Configuration'' You need to add the following to such a file for each
serial port (example is ttyS2) you want to enable hardware flow
control on:
stty -F /dev/ttyS2 crtscts
or
stty crtscts < /dev/ttyS2
If you want to see if flow control is enabled do the following: In
minicom (or the like) type AT&V (or ATI4 on 3Com modems) to see how
the modem is configured and look for &K3 (or &H1 on 3Com modems) which
means hardware flow control. Then without exiting the communications
program (such as minicom) see if the device driver knows about it by
typing: stty -F /dev/ttyS2 -a. Look for "crtscts" (without a
disabling minus sign). Remember that communication programs change
these settings so you may want to check them after you have started up
your communication program.
[1m7.3. Speed Settings[0m
Besides flow control there is speed. See ``What Speed Should I Use
with My Modem''. There's also are parity and bits-per-byte settings.
Normally the port is set by the communications program at 8N1 (8-bits
per byte, No parity, and 1 stop bit). If you're running PPP then you
must use 8N1. So if you get a complaint that it's not 8-bit clean
then it's likely not 8N1 like it should be.
[1m7.4. Ignore CD Setting: clocal[0m
Normally a CD (Carrier Detect) signal (on the CD wire for an external
modem) is required before a serial port can be opened. But if stty
has negated clocal (-clocal), then the port requires CD raised for the
port to open and remain open. Actually, a skilled programmer can
write the program in such a way as to force the port to open even when
CD and clocal say not to. So if stty shows -clocal then there might
be a problem with opening the port. But for dial-in, in some cases
you may want -clocal so that when the remote modem stops sending a
carrier and CD drops, the port will close and terminate all processes
running on it.
One way to keep CD raised is to send "AT&C" to the modem so that CD
from the modem will always be on. CD always-on is fine for dial-out
but for dial-in, the CD signal is sometimes (but rarely) used to
detected an incoming call.
clocal may be asserted by default in recent serial drivers. Minicom
raises clocal automatically when it starts up so there is no problem
with it opening the port. But it restores the clocal setting to it's
original when you exit minicom. But version 6.0.192 of Kermit hung
when I set -clocal and tried to "set line ...".
[1m7.5. What is stty ?[0m
stty is something like setserial but it sets the speed (baud rate),
hardware flow control, and other parameters of a serial port. Typing
"stty -F /dev/ttyS2 -a" should show you how ttyS2 is configured. Most
of the stty settings are for things that you never need to use with
modems. Many of the setting are only needed for Text-Terminals (and
some are only needed for antique terminals of the 1970s). Your
communication package should automatically set up the several settings
needed for modems. For this reason you normally don't need to use
stty so it's not covered much in this Modem-HOWTO. But stty is
sometimes useful for trouble-shooting. More is said about stty in
the Serial-HOWTO or Text-Terminal-HOWTO..
[1m8. Modem Configuration (excluding serial port)[0m
[1m8.1. Finding Your Modem[0m
Before spending a lot of time deciding how to configure your modem,
you first need to make sure it can be found and that AT-commands and
the like can be sent to it. So I suggest you first give it a very
simple configuration using the communication program you will be using
on the port and see it it works. If this works you may then want to
improve on the configuration, If not then see ``My Modem is Physically
There but Can't be Found''. A winmodem may be hard to find and will
not work under Linux.
[1m8.2. AT Commands[0m
While the serial port on which a modem resides requires configuring,
so does the modem itself. The modem is configured by sending AT
commands (or the like) to it on the same serial line that is used to
send data.
Most modems use an AT command set. These are cryptic and short ASCII
commands where all command strings must be prefaced by the letters AT.
AT means: ATtention, expect a command to follow. For example:
ATZ&K3<return> This is an AT-command string with two commands here: Z
and &K3. Z is short for Z0 and a few modems require that you use Z0
instead of just Z. It's like this for other commands ending in 0.
The command string is terminated by a return character (use the
<enter> key if you are manually typing it). A string that's too long
(40 or more characters) may not work on older modems. You may use
either uppercase or lowercase letters.
Unfortunately there are many different variations of the AT command
set so that what works for one modem may or may not work for another
modem. Thus there is no guarantee that the AT commands given in this
section will work on your modem.
Such command strings are either automatically sent to the modem by
communication programs or are manually typed in by you. Most
communication programs provide a screen where you may change (edit)
and save the init string that the communication program will use. The
modem itself has a stored configuration (profile) which is like a long
init string. It represents the configuration of the modem when it's
first tuned on. You may change it to suit your taste. In most cases
there are a few different such configurations (profiles) and there are
ways to designate one of them to be active.
If you have a manual for your modem (either on paper or on floppy
disk) you might find AT-commands there. 3Com modems (and others ??)
have AT-Command help files built into the modem so if you type say
"AT$" to the modem it will display some "online help".
You can also find info on AT commands on the Internet. You should
first try a site for your modem manufacturer. If this doesn't work
out then you can search the Internet using terms that are from AT
commands such as &C1, &D3, etc. This will tend to find sites that
actually list AT-Commands instead of sites that just talk about them
in general. You might also try a few of the sites listed in the
subsection ``Web Sites''. Be warned that the AT-commands for a
different brand of modem may be somewhat different.
[1m8.3. Init Strings: Saving and Recalling[0m
The examples given in this subsection are from the Hayes AT modem
command set. All command strings must be prefaced by the two letters
AT. For example: AT&C1&D3^M (^M is the return character). When a
modem is powered on, it automatically configures itself with one of
the configurations it has stored in its non-volatile memory. If this
configuration is satisfactory there is nothing further to do.
If it's not satisfactory, then one may either alter the stored
configuration or configure the modem each time you use it by sending
it a string of commands known as an "init string" (= initialization
string). Normally, a communication program does this. What it sends
will depend on how you configured the communications program. Your
communication program should allow you to edit the init string and
change it to whatever you want. Sometimes the communications program
will let you select the model of your modem and then it will use an
init string that it thinks is best for that modem.
The configuration of the modem when it's first powered on may be
expressed by an init string. You might think of this as the default
"string" (called a profile). If your communications program sends the
modem another string (the init string), then this string will modify
the default configuration. For example, if the init string only
contains two commands, then only those two items will be changed.
However, some commands will recall a stored profile from inside the
modem so a single such command in the init string can thereby change
everything in the configuration.
Modern modems have a few different stored profiles to choose from that
are stored in the modem's non-volatile memory (it's still there when
you turn it off). In my modem there are two factory profiles (0 and
1, neither of which you can change) and two user defined profiles (0
and 1) that the user may set and store. Your modem may have more. To
view some of these profiles send the command &V. At power-up one of
the user-defined profiles is loaded. For example, if you type the
command &Y0 (just Y0 for a 3Com modem) then in the future profile 0
will be used at power-on.
There are also commands to load (activate) any of the stored profiles.
Such a load command may be put in an init string. Of course if it
loads the same profile that was automatically loaded at power-up,
nothing is changed (unless the active profile has been modified since
power-up). Since your profile could have thus been modified it's a
good idea to use some kind of an init string even if it does nothing
more than load a stored profile.
Examples of loading saved profiles:
Z0 loads user-defined profile 0 and resets (hangs up, etc.)
&F1 loads factory profile 1
Once you have sent commands to the modem to configure it the way you
want (such as loading a factory profile and modifying it a little) you
may save this as a user-defined profile:
&W0 saves the current configuration to user-profile 0.
Many people don't bother saving a good configuration in their modem,
but instead, send the modem a longer init string each time the modem
is used. Another method is to restore the factory default by &F1 at
the start of the init string and then modify it a little by adding a
few other commands to the end of the init string. Since there is no
way to modify the factory default this prevents anyone from changing
the configuration by modifying (and saving) the user-defined profile.
You may choose an init string supplied by someone else that they think
is right for your modem. Some communication programs have a library
of init strings to select from. The most difficult method (and one
which will teach you the most about modems) is to study the modem
manual and write one yourself. You could save this configuration
inside the modem so that you don't need an init string. A third
alternative is to start with an init string that someone else wrote,
but modify it to suit your purposes.
If you look at init strings used by communication programs you may see
symbols which are not valid modem commands. These symbols are
commands to the communication program itself and will not be sent to
the modem. For example, ~ may mean to pause briefly.
[1m8.3.1. Where is my "init string" so I can modify it ?[0m
This depends on your communication program (often a PPP program). If
this is the latest version of Modem-HOWTO send me info for other
cases.
· Gnome: run pppsetup
· wvdial: edit /etc/wvdial.conf
· minicom: hit ^Ao (or possibly ALT-o), then select "Modem and
Dialing"
[1m8.4. Other AT Modem Commands[0m
For dial-in see ``Dial-in Modem Configuration''. The rest of this
section is mostly what was in the old Serial-HOWTO. All strings must
start with AT. Here's a few Hayes AT codes that should be in the
string (if they are not set by using a factory default or by a saved
configuration).
· E1 command echo ON
· Q0 result codes are reported
· V1 result codes are verbose
· S0=0 never answer (uugetty does this with the WAITFOR option)
Here's some more AT commands for special purposes:
· &C1 CD is only on when you're connected
· &S0 DSR is always on
· X3 Dial even if there is no dialtone (Blind dial. Use where dial-
tones don't exist).
Note: to get his old USR Courier V.34 modem to reset correctly when
DTR drops, Greg Hankins had to set &D2 and S13=1 (this sets bit 0 of
register S13). This has been confirmed to work on USR Sportster V.34
modems as well.
Note: some old Supra modems treat CD differently than other modems.
If you are using a Supra, try setting &C0 and [4mnot[24m &C1. You must also
set &D2 to handle DTR correctly.
[1m8.5. Blacklisting[0m
If phone number is dialed a few times with no success, some modems may
blacklist a phone number. After a certain time you may try again.
Some countries require this to reduce needless repeated dialing. To
view the blacklist try %B. To delete the blacklist use these AT
commands:
· SR Robotics o 3COM: s40=2 or if NG try s40=7
· Lucent: %t21,18,0
· Rockwell: %tcb
· Cirrus Logic: *nc9
[1m8.6. What AT Commands are Now Set in my Modem?[0m
You may try to use minicom for viewing your modem profile. It's best
not to have any other process running on the modem port when you do
this. If you have set up minicom for your modem, then you may type on
the command line: minicom -o to start minicom without restoring the
saved modem profile. Then type at&v (or atI4 on 3Com modems) to
display the profile. To exit minicom without disturbing this profile,
use the q (quit) command for exiting without resetting.
The above may not work for various reasons. If the modem has been set
not to echo result codes it may not even display any profile. If
there is another process running on the modem port at the same time,
some of what the modem sends to you is likely to be read by the other
process so you will see only part of the profile. Is there some way
to temporarily stop the other process on the port so it will not
interfere? I tried the "stop" signal using the "kill" command but it
didn't work. If this is the latest version of this HOWTO, let me know
if you find a way to do it.
If you have at least one process running on the modem port and kill
them, the modem's profile may be reset so you will not observe what
the original profile was. This will happen if you kill getty (or it's
replacements: login or bash) and have &D3 set. The killing of getty
(or the like) will drop DTR and reset the modem's profile to the
power-on state. To keep getty from respawning when killed, comment
it out in /etc/inittab and do an "init q".
[1m8.7. Modem States (or Modes)[0m
Since the channel for sending AT commands to the modem is the same
channel that is used for the flow of data (files, packets, etc.) then
it's important to cleanly separate the AT commands from the data.
When the modem is first turned on it's in the command mode (also
called terminal mode, idle state or AT-command mode). Anything sent
to it from the PC is assumed to be an AT command and not data. Then
if a dial command is sent to it (ATD...), it dials and connects to
another modem. It's now in the on-line data mode (connected) and
sends and receives data (such as Internet pages). In this mode, any
AT command one trys to send it will not work but will be transmitted
to the other modem instead. Except for the escape command. This is
+++ with a minimum time delay both at the start and end. The time
delay allows the modem to determine that it is likely a real escape
and not just +++ in a file being transmitted.
So we have two states so far: AT-command and on-line data. But there
is a third important state which is sort of a combination of these
two. It's the on-line command mode. This is when the modem maintains
a connection (without sending/receiving data) but anything sent from
the PC is interpreted as an AT command. This is the state reached
with a +++ escape signal or by a DTR drop from the PC provided the &D1
has been set. Then one can send AT commands to the modem including
commands which will leave this state and go to one of the other two
states.
There are other states also: dialing state and handshaking state but
they normally lead to the connected (on-line) state. If they don't
then the modem should hang up, thereby returning to the initial AT-
command (or idle) state.
[1m9. Serial Port Devices /dev/ttyS4, (or /dev/ttys/4) etc.[0m
[1m9.1. Serial Port Names: ttyS4, tts/2, etc.[0m
Once upon a time the names of the serial ports were simple. Except
for some multiport serial cards they were named /dev/ttyS0,
/dev/ttyS1, etc. Then around the year 2000 came the USB bus with
names like /dev/ttyUSB0 and /dev/ttyACM1 (for the ACM modem on the USB
bus).
A little later with kernel 2.4 came the "device file system" (devfs)
with a whole new set of names for everything. The use of the device
file system was optional and many still continued using the old
system. Then in 2003-4, it was claimed that devfs had unsolvable
problems and will be replaced with what's called "udev". Although
udev doesn't provide all the functionality of devfs it does handle hot
plugging. With all this confusion, most distributions use neither
devfs nor udev.
If you use devfs or udev, ttyS1 becomes tts/1, ttyUSB1 becomes
/usb/tts/1, and ttyACM1 is /usb/acm/1. Note that the the number 1
above is just an example. It could be replaced by 0, 2, 3, 4, etc.
One may use devfs but have the conventional names linked (via
symlinks) to the new names. So they use the new system with the old
names but may also use some of the new names for some devices. It's
even possible ?? to use the new names for the old (non-devfs) system.
[1m9.2. The PCI Bus[0m
Since DOS provided for 4 serial ports on the old ISA bus: COM1-COM4,
ttyS0-ttyS3 (tts/0-tts/3) most serial ports on the newer PCI bus use
higher numbers such as ttyS4 (tts/4) or ttyS14 (tts/14) for kernel
2.6. This permits one to have both ISA serial ports and PCI serial
ports on the same PC with no name conflicts. 0-3 are reserved for the
old ISA bus and 4-upward (or 14-upward) are used for PCI. It's not
required to be this way but it often is. On-board serial ports on
motherboards which have both PCI and ISA slots are likely to still be
ISA ports. Even for all-PCI-slot motherboards, the serial ports are
often not PCI. They are either ISA, on an internal ISA bus or on a
LPC bus which is intended for slow legacy I/O devices: serial/parallel
ports and floppy drives.
[1m9.3. Devfs (The Device File System)[0m
In kernel 2.4 the devfs was created only to be obsoleted in favor of
udev in kernel 2.6. devfs creased a new system of device naming which
was continued with udev. The naming system makes it easier to deal
with a huge number of devices. But there's also a popular option to
continue using the old names. However, a new device may not have an
old-style name so then one must use the new name. For a detailed
description of devfs see:
<http://www.atnf.csiro.au/~rgooch/linux/docs/devfs.html> Also see the
kernel documentation tree: filesystems/devfs.
Some more examples of devfs names: ttyS2 becomes tts/2 (Serial port),
tty3 becomes vc/3 (Virtual Console), ptyp1 becomes pty/m1 (PTY
master), ttyp2 becomes pty/s2 (PTY slave). "tts" looks like a
directory which contains devices "files": 0, 1, 2, etc. All of these
new names should still be in the /dev directory although optionally
one may put them elsewhere.
For devfs, device names in the /dev directory are created
automatically by the corresponding driver. Thus, if serial support
comes from a module and that module isn't loaded yet, there will not
be any serial devices in the /dev directory. This can be confusing:
you physically have serial ports but don't see them in the /dev
directory. However, if a device name is told to a communication
program and the serial module isn't loaded, the kernel is supposed to
try to find a driver for it and create a name for it in the /dev
directory.
This is works OK if it finds a driver. But suppose there is no driver
found for it. For example, if you try to use "setserial" to configure
a port that the driver failed to detect, it claims there is no such
port. How does one create a devfs port in this case?
[1m9.4. Legacy Serial Port Device Names & Numbers[0m
Before the device file system, devices in Linux had major and minor
numbers. The serial port ttySx (x=0,1,2, etc.) was major number 4.
You could see this (and the minor numbers too) by typing: "ls -l
ttyS*" in the /dev directory. To find the old device names for
various devices, see the "devices" file in the kernel documentation.
There formerly was a "cua" name for each serial port and it behaved
just a little differently. For example, ttyS2 would correspond to
cua2. It was mainly used for modems. The cua major number was 5 and
minor numbers started at 64. You may still have the cua devices in
your /dev directory but they are now deprecated. For details see
Modem-HOWTO, section: cua Device Obsolete.
For creating the old devices in the device directory see: the Serial-
HOWTO: "Creating Devices In the /dev directory".
[1m9.5. More on Serial Port Names[0m
Dos/Windows use the COM name while the messages from the serial driver
use ttyS00, ttyS01, etc. Older serial drivers (2001 ?) used just
tty00, tty01, etc.
The tables below shows some examples of serial device names. The IO
addresses are the default addresses for the old ISA bus (not for the
newer PCI and USB buses). The major/minor numbers aren't needed for
the devfs, but they often exist anyway just in case the devfs method
of locating drivers can't be used.
dos devfs common IO
name name name major minor address
COM1 /dev/tts/0 /dev/ttyS0 4, 64; 3F8
COM2 /dev/tts/1 /dev/ttyS1 4, 65; 2F8
COM3 /dev/tts/2 /dev/ttyS2 4, 66; 3E8
COM4 /dev/tts/3 /dev/ttyS3 4, 67; 2E8
- /dev/tts/4 /dev/ttyS4 4, 68; various
DEVICES-ON-THE-USB-BUS (acm is a certain type of modem)
devfs common name devfs common name
/dev/usb/tts/0 /dev/ttyUSB0 | /dev/usb/acm/0 /dev/ttyACM0
/dev/usb/tts/1 /dev/ttyUSB1 | /dev/usb/acm/1 /dev/ttyACM1
/dev/usb/tts/2 /dev/ttyUSB2 | /dev/usb/acm/2 /dev/ttyACM2
/dev/usb/tts/3 /dev/ttyUSB3 | /dev/usb/acm/3 /dev/ttyACM3
[1m9.6. USB (Universal Serial Bus) Serial Ports[0m
For more info see the usb subdirectory in the kernel documentation
directory for files: usb-serial, acm, etc.
[1m9.7. Link ttySN to /dev/modem[0m
On some installations, two extra devices will be created, /dev/modem
for your modem and /dev/mouse for a mouse. Both of these are symbolic
links to the appropriate serial device in /dev which you specified
during the installation Except if you have a bus mouse, then
/dev/mouse will point to the bus mouse device).
Historical note: Formerly (in the 1990s) the use of /dev/modem was
discouraged since lock files might not realize that it was really say
/dev/ttyS2. The newer lock file system doesn't fall into this trap so
it's now OK to use such links.
[1m9.8. cua Device Obsolete[0m
Each ttyS device has a corresponding cua device. But the cua device
is deprecated so it's best to use ttyS (unless cua is required).
There is a difference between cua and ttyS but a savvy programmer can
make a ttyS port behave just like a cua port so there is no real need
for the cua anymore. Except that some older programs may need to use
the cua.
What's the difference? The main difference between cua and ttyS has
to do with what happens in a C-program when an ordinary "open" command
tries to open the port. If a cua port has been set to check modem
control signals, the port can be opened even if the CD modem control
signal says not to. Astute programming (by adding additional lines to
the program) can force a ttyS port to behave this way also. But a cua
port can be more easily programmed to open for dialing out on a modem
even when the modem fails to raise CD (since no one has called into it
and there's no carrier). That's why cua was once used for dial-out
and ttyS used for dial-in.
Starting with Linux kernel 2.2, a warning message is put in the kernel
log when one uses cua. This is an omen that cua is defunct and should
be avoided if possible.
[1m10. Interesting Programs You Should Know About[0m
[1m10.1. What is setserial ?[0m
This part is in 3 HOWTOs: Modem, Serial, and Text-Terminal. There are
some minor differences, depending on which HOWTO it appears in.
[1m10.1.1. Important information[0m
The setserial program doesn't seem to work if the serial port is for a
linmodem such as ttySHCF0. If you have a Laptop (PCMCIA) don't use
setserial until you read ``Laptops: PCMCIA''.
[1m10.1.2. Introduction[0m
setserial is a program which allows you (or a shell script) to talk to
the serial device driver software. But there's also another program
tt/stty/ that also deals with the serial port and is used for setting
the port speed, etc.
setserial deals with the lower-level configuring of the serial port,
such as dealing with IRQs (such as 5), port addresses (such as 3f8),
and the like. A major problem with it is that it can't set or
configure the serial port hardware: It can't set the IRQ or port
addresses into the hardware. Furthermore, when it reports the
configuration of the hardware, it's sometimes wrong since it doesn't
actually probe the hardware unless you specifically tell it to. Even
then, it doesn't do the modern type of bus probing and what's there
may never be found by it. Actually, what it shows is right most all
the time but if you're having trouble getting a serial port to work,
then there's a fair chance it's wrong.
In olden days, when the IRQ and port address was set by jumpers on the
serial card, one would use setserial to tell the driver how these
jumpers were set. Today, when plug-and-play methods detect how the
jumperless serial port is set, setserial is not really needed anymore
unless you're having problems or using old hardware. Furthermore, if
the configuration file used by setserial is wrong, then there's
trouble. In this case, if you use setserial to try to find out how
the port is configured, it may just repeat the incorrect information
in the configuration file.
setserial can sometimes be of help to find a serial port. But it's
only of use if you know the port address and use the right options.
For modern port's, there's usually better ways to look for them by
plug-and-play methods.
Thus the name setserial is somewhat of a misnomer since it doesn't set
the I/O address nor IRQ in the hardware, it just "sets" them in the
driver software. And the driver naively believes that what setserial
tells it, even if it conflicts with what the driver has found by using
plug-and-play methods. Too bad that it fails to at least issue a
warning message for such a conflict. Since the device driver is
considered to be part of the kernel, the word "kernel" is often used
in other documentation with no mention made of any "serial driver".
Some distributions (and versions) set things up so that setserial is
run at boot-time by an initialization shell script (in the /etc
directory tree). But the configuration file which this script uses
may be either in the /etc tree or the /var tree. In some cases, if
you want setserial to run at boot-time, you may have to take some
action. setserialwill not work without either serial support built
into the kernel or loaded as a module. The module may get loaded
automatically if you (or a script) attempt to use setserial.
While setserial can be made to probe the hardware I0 port addresses to
try to determine the UART type and IRQ, this has severe limitations.
See ``Probing''. It can't set the IRQ or the port address in the
hardware of PnP or PCI serial ports (but the plug-and-play features of
the serial driver may do this). It also can't directly read the PnP
data stored in configuration registers in the hardware. But since the
device driver can read these registers and setserial tells you what
the device driver thinks, it might be correct. Or it could be telling
you what setserial had previously (and perhaps erroneously) told the
driver. There's no way to know for sure without doing some other
checks.
The serial driver (for Linux Kernel 2.4+) looks for a few "standard"
legacy serial ports, for PnP ports on the ISA bus, and for all
supported port hardware on the PCI bus. If it finds your ports
correctly, then there's no need to use setserial. The driver doesn't
probe for legacy IRQs and may get these wrong and it may miss old ISA
serial ports set with jumpers on the card.
Besides the man page for setserial, check out info in
/usr/doc/setserial.../ or /usr/share/doc/setserial. This should tell
you how setserial is handled for your distribution of Linux. While
setserial behaves the same in all distributions, the scripts for
running it, how to configure such scripts (including automatic
configuration), and the names and locations of the script files, etc.,
are all distribution-dependent.
[1m10.1.3. Serial module unload[0m
If a serial module gets unloaded, the changes previously made by
setserial will be forgotten by the driver. But while the driver
forgets it, a script provided by the distribution may save it in a
file somewhere so that it can the restored if the module is reloaded.
[1m10.1.4. Giving the setserial command[0m
Remember, that setserial can't set any I/O addresses or IRQs in the
hardware. That's done either by plug-and-play software (run by the
driver) or by jumpers for legacy serial ports. Even if you give an
I/O address or IRQ to the driver via setserial it will not set such
values and assumes that they have already been set. If you give it
wrong values, the serial port will not work right (if at all).
For legacy ports, if you know the I/O address but don't know the IRQ
you may command setserial to attempt to determine the IRQ.
You can see a list of possible commands by just typing setserial with
no arguments. This fails to show you the one-letter options such as
-v for verbose which you should normally use when troubleshooting.
Note that setserial calls an IO address a "port". If you type:
setserial -g /dev/ttyS*
you'll see some info about how the device driver is configured for
your ports. Note that where it says "UART: unknown" it probably means
that no uart exists. In other words, you probably have no such serial
port and the other info shown about the port is meaningless and should
be ignored. If you really do have such a serial port, setserial
doesn't recognize it and that needs to be fixed.
If you add -a to the option -g you will see more info although few
people need to deal with (or understand) this additional info since
the default settings you see usually work fine. In normal cases the
hardware is set up the same way as "setserial" reports. But if you
are having problems there is a good chance that setserial has it
wrong. In fact, you can run "setserial" and assign a purely
fictitious I/O port address, any IRQ, and whatever uart type you would
like to have. Then the next time you type "setserial ..." it will
display these bogus values you've supplied to the driver. They will
also be officially registered with the kernel as displayed (at the top
of the screen) by the "scanport" command (Debian). Of course the
serial port driver will not work correctly (if at all) if you attempt
to use such a port. Thus, when giving parameters to setserial,
"anything goes". Well almost. If you assign one port a base address
that is already assigned (such as 3e8) it may not accept it. But if
you use 3e9 it will accept it. Unfortunately 3e9 is actually assigned
since it is within the range starting at base address 3e8. Thus the
moral of the story is to make sure your data is correct before
assigning resources with setserial.
[1m10.1.5. Configuration file[0m
While assignments made by setserial are lost when the PC is powered
off, a configuration file may restore them when the PC is started up
again. In newer versions, what you change by setserial might get
automatically saved to a configuration file. When setserial runs it
uses the info from the the configuration file.
Where this configuration file resides depends on your distribution.
Look at the start-up scripts somewhere in the /etc/ tree (such as
/etc/init.d/ or /etc/rc.d/) and read the startup script for "serial"
or "setserial" or the like. It should show where the configuration
file(s) reside. In Debian there are 4 options for use of this
configuration file:
1. Don't use this file at all. At each boot, the serial driver alone
detects the ports and setserial doesn't ever run. ("kernel"
option)
2. Save what setserial reports when the system is first shutdown and
put it in the configuration file. After that, don't ever make any
changes to the configuration file, even if someone has made changes
by running the setserial command on the command line and then shuts
down the system. ("autosave-once" option)
3. At every shutdown, save whatever setserial detects to the
configuration file. ("autosave" option)
4. Manually edit the configuration file to set the configuration.
Don't ever do any automatic saves to it. ("manual" option)
In olden days (perhaps before 2000), there wasn't any configuration
file and the configuration was manually set (hard coded) inside the
shell script that ran setserial. See ``Edit a script (prior to
version 2.15)''.
[1m10.1.6. Probing[0m
You probe for a port with setserial only when you suspect that it has
been enabled (by PnP methods, the BIOS, jumpers, etc.). Otherwise
setserial probing will never find it since its address doesn't exist.
A problem is where the software looks for a port at specified I/O
addresses. Prior to probing with "setserial", one may run the
"scanport" (Debian) command to check all possible ports in one scan.
It makes crude guesses as to what is on some ports but doesn't
determine the IRQ. It's a fast first start. It may hang your PC but
so far it's worked fine for me. Note that non-Debian distributions
don't seem to supply "scanport". Is there another scan program?
With appropriate options, setserial can probe (at a given I/O address)
for a serial port but you must guess the I/O address. If you ask it
to probe for /dev/ttyS2 for example, it will only probe at the address
it thinks ttyS2 is at (2F8). If you tell setserial that ttyS2 is at a
different address, then it will probe at that address, etc. See
``Probing''
The purpose of such probing is to see if there is a uart there, and if
so, what its IRQ is. Use setserial mainly as a last resort as there
are faster ways to attempt it such as wvdialconf to detect modems,
looking at very early boot-time messages, or using pnpdump --dumpregs,
or lspci -vv. But if you want to detect hardware with setserial use
for example :
/dev/ttyS2 -v autoconfig
If the resulting message shows a uart type such as 16550A, then you're
OK. If instead it shows "unknown" for the uart type, then there is
supposedly no serial port at all at that I/O address. Some cheap
serial ports don't identify themselves correctly so if you see
"unknown" you still might have a serial port there.
Besides auto-probing for a uart type, setserial can auto-probe for
IRQ's but this doesn't always work right either. In one case it first
gave the wrong irq but when the command was repeated it found the
correct irq. In versions of setserial >= 2.15, the results of your
last probe test could be automatically saved and put into a
distribution-specific configuration file such as /etc/serial.conf or
/etc/sysconfig/serial or /var/lib/setserial/autoserial.conf for
Debian. This will be used next time you start Linux.
It may be that two serial ports both have the same IO address set in
the hardware. Of course this is not normally permitted for the ISA
bus but it sometimes happens anyway. Probing detects one serial port
when actually there are two. However if they have different IRQs,
then the probe for IRQs may show IRQ = 0. For me, it only did this if
I first used setserial to give the IRQ a fictitious value.
[1m10.1.7. Boot-time Configuration[0m
While setserial may run via an initialization script, something akin
to setserial also runs earlier when the serial module is loaded (or
when the kernel starts the built-in serial driver if it was compiled
into the kernel). Thus when you watch the start-up messages on the
screen it may look like it ran twice, and in fact it has.
If the first message is for a legacy port, the IRQs shown may be wrong
since it didn't probe for IRQs. If there is a second report of serial
ports, it may the result of a script such as /etc/init.d/setserial.
It usually does no probing and thus could be wrong about how the
hardware is actually set. It only shows configuration data that got
saved in a configuration files. The old method, prior to setserial
2.15, was to manually write such data directly into the script.
When the kernel loads the serial module (or if the "module equivalent"
is built into the kernel) then all supported PnP ports are detected.
For legacy (non-PnP) ports, only ttyS{0-3} are auto-detected and the
driver is set to use only IRQs 4 and 3 (regardless of what IRQs are
actually set in the hardware). No probing is done for IRQs but it's
possible to do this manually. You see this as a boot-time message
just as if setserial had been run.
To correct possible errors in IRQs (or for other reasons) there may be
a script file somewhere that runs setserial. Unfortunately, if this
file has some IRQs wrong, the kernel will still have incorrect info
about the IRQs. This file is usually part of the initialization done
at boot-time. Whether it runs or not depends on how you (and/or your
distribution) have set things up. It may also depends on the
runlevel.
Before modifying a configuration file, you can test out a "proposed"
setserial command by just typing it on the command line. In some
cases the results of this use of setserial will automatically get
saved somewhere such as /etc/serial.conf (or autoserial.conf or
serial) when you shutdown. So if it worked OK (and solved your
problem) then there's no need to modify any configuration file. See
``Configuration method using /etc/serial.conf, etc.''.
[1m10.1.8. Edit a script (required prior to version 2.15)[0m
This is how it was done prior to setserial 2.15 (1999) The objective
was to modify (or create) a script file in the /etc tree that runs
setserial at boot-time. Most distributions provided such a file (but
it may not have initially resided in the /etc tree).
So prior to version 2.15 (1999) it was simpler. All you did was edit
a script. There was no /etc/serial.conf file (or the like) to
configure setserial. Thus you needed to find the file that runs
"setserial" at boot time and edit it. If it didn't exist, you needed
to create one (or place the commands in a file that ran early at boot-
time). If such a file was currently being used it's likely was
somewhere in the /etc directory-tree. But Redhat <6.0 has supplied it
in /usr/doc/setserial/ but you need to move it to the /etc tree before
using it.
The script /etc/rc.d/rc.serial was commonly used in the past. The
Debian distribution used /etc/rc.boot/0setserial. Another file once
used was /etc/rc.d/rc.local but it's may not have run early enough.
It's was reported that other processes may try to open the serial port
before rc.local ran resulting in serial communication failure. Later
on it's most likely was found in /etc/init.d/ but wasn't normally
intended to be edited.
If such a file was supplied, it likely contained a number of
commented-out examples. By uncommenting some of these and/or
modifying them, you could set things up correctly. It was important
use a valid path for setserial, and a valid device name. You could do
a test by executing this file manually (just type its name as the
super-user) to see if it works right. Testing like this was a lot
faster than doing repeated reboots to get it right.
For versions >= 2.15 (provided your distribution implemented the
change, Redhat didn't as first) it may be more tricky to do since the
file that runs setserial on startup, /etc/init.d/setserial or the like
was not intended to be edited by the user. See ``Configuration method
using /etc/serial.conf, etc.''.
An example line in such a script was"
/sbin/setserial /dev/ttyS3 irq 5 uart 16550A skip_test
or, if you wanted setserial to automatically determine the uart and
the IRQ for ttyS3 you would have used something like this:
/sbin/setserial /dev/ttyS3 auto_irq skip_test autoconfig
This was done for every serial port you wanted to auto configure,
using a device name that really does exist on your machine. In some
cases it didn't work right due to the hardware.
[1m10.1.9. Configuration method using /etc/serial.conf, etc.[0m
Prior to setserial version 2.15 (1999), the way to configure setserial
was to manually edit the shell-script that ran setserial at boot-time.
See ``Edit a script (before version 2.15)''. Today the script and
configuration file are two different files instead of one. This
shell-script is not edited but gets its data from a configuration file
such as /etc/serial.conf (or /var/lib/setserial/autoserial.conf).
Furthermore you may not even need to edit serial.conf (or the like)
because using the "setserial" command on the command line may
automatically cause serial.conf to be edited appropriately. This was
done so that you don't need to edit any file in order to set up (or
change) what setserial does each time that Linux is booted.
What often happens is this: When you shut down your PC the script
that ran "setserial" at boot-time is run again, but this time it only
does what the part for the "stop" case says to do: It uses
"setserial" to find out what the current state of "setserial" is, and
it puts that info into the serial configuration file such as
serial.conf. Thus when you run "setserial" to change the serial.conf
file, it doesn't get changed immediately but only when and if you shut
down normally.
Now you can perhaps guess what problems might occur. Suppose you
don't shut down normally (someone turns the power off, etc.) and the
changes don't get saved. Suppose you experiment with "setserial" and
forget to run it a final time to restore the original state (or make a
mistake in restoring the original state). Then your "experimental"
settings are saved. There's an option to avoid this in Debian known
as "AUTOSAVE-ONCE" which will be discussed later on.
If you manually edit serial.conf, then your editing is destroyed when
you shut down because it gets changed back to the state of setserial
at shutdown. There is a way to disable the changing of serial.conf at
shutdown and that is to remove "###AUTOSAVE###" or the like from first
line of serial.conf. In the Debian distribution, the removal of
"###AUTOSAVE###" from the first line was once automatically done after
the first time you shutdown just after installation. To retain this
effect the "AUTOSAVE-ONCE" option was created which only does a save
when time the system is shut down for the first time (just after you
install or update the setserial program).
The file most commonly used to run setserial at boot-time (in
conformance with the configuration file) is now /etc/init.d/setserial
(Debian) or /etc/init.d/serial (Redhat), or etc., but it should not
normally be edited. For 2.15, Redhat 6.0 just had a file
/usr/doc/setserial-2.15/rc.serial which you have to move to
/etc/init.d/ if you want setserial to run at boot-time.
To disable a port, use setserial to set it to "uart none". This will
not be saved. The format of /etc/serial.conf appears to be just like
that of the parameters placed after "setserial" on the command line
with one line for each port. If you don't use autosave, you may edit
/etc/serial.conf manually.
In order to force the current settings set by setserial to be saved to
the configuration file (serial.conf) without shutting down, do what
normally happens when you shutdown: Run the shell-script
/etc/init.d/{set}serial stop. The "stop" command will save the
current configuration but the serial ports still keep working OK.
In some cases you may wind up with both the old and new configuration
methods installed but hopefully only one of them runs at boot-time.
Debian labeled obsolete files with "...pre-2.15".
[1m10.1.10. IRQs[0m
By default, both ttyS0 and ttyS2 will share IRQ 4, while ttyS1 and
ttyS3 share IRQ 3. But while sharing serial interrupts (using them in
running programs) is OK for the PCI bus, it's not permitted for the
ISA bus unless you: 1. have kernel 2.2 or better, and 2. you've
complied in support for this, and 3. your serial hardware supports it.
See
``Interrupt sharing and Kernels 2.2+'' If you only have two serial
ports, ttyS0 and ttyS1, you're still OK since IRQ sharing conflicts
don't exist for non-existent devices.
If you add a legacy internal modem (without plug-and-play) and retain
ttyS0 and ttyS1, then you should attempt to find an unused IRQ and set
it both on your serial port (or modem card) and then use setserial to
assign it to your device driver. If IRQ 5 is not being used for a
sound card, this may be one you can use for a serial port for a modem.
[1m10.1.11. Laptops: PCMCIA[0m
If you have a Laptop, read PCMCIA-HOWTO for info on the serial
configuration. For serial ports on the motherboard, setserial is used
just like it is for a desktop. But for PCMCIA cards (such as a modem)
it's a different story. The configuring of the PCMCIA system should
automatically run setserial so you shouldn't need to run it. If you
do run it (by a script file or by /etc/serial.conf) it might be
different and cause trouble. The autosave feature for serial.conf
shouldn't save anything for PCMCIA cards (but Debian did until
2.15-7). Of course, it's always OK to use setserial to find out how
the driver is configured for PCMCIA cards.
[1m10.2. What is isapnp ?[0m
isapnp is a program to configure Plug-and-Play (PnP) devices on the
ISA bus including internal modems. It comes in a package called
"isapnptools" and includes another program, "pnpdump" which finds all
your ISA PnP devices and shows you options for configuring them in a
format which may be added to the PnP configuration file:
/etc/isapnp.conf. It may also be used with the --dumpregs option to
show the current IO address and IRQ of the modem's serial port. The
isapnp command may be put into a startup file so that it runs each
time you start the computer and thus will configure ISA PnP devices.
It is able to do this even if your BIOS doesn't support PnP. See
Plug-and-Play-HOWTO.
[1m10.3. What is wvdialconf ?[0m
wvdialconf will try to find which serial port (ttyS?) has a modem on
it. It also creates a configuration program for the wvdial program.
wvdial is used for simplified dialing out using the PPP protocol to an
ISP. It can also look for modems which are not currently in use. It
will automatically devise a "suitable" init string for the modem but
sometimes gets it wrong. Since this command has no options, it's
simple to use but you must give it the name of a file to put the init
string (and other data) into. For example type: wvdialconf
my_config_file_name.
[1m11. Trying Out Your Modem (Dialing Out)[0m
[1m11.1. Are You Ready to Dial Out ?[0m
Once you've plugged in your modem and know which serial port it's on
you're ready to try using it. The protocol on the telephone line will
be PPP (Point-to-Point Protocol), but PPP often gets set up without
you needing to know much about it. If you already have an account with
an ISP to connect to the Internet, you could try using a program like
"wvdial" to connect to the Internet.
As an alternative to taking one big step using PPP to connect to the
Internet, you could do a two step process: First just test out your
modem without using PPP (using Minicom or Kermit). Then if your modem
works OK, use "wvdial" or another ppp dialer to connect to the
Internet. A different strategy is to first try a ppp dialer and then
if that doesn't work out, fallback to Minicom or Kermit to see if your
modem works OK. Knowing how to use either Minicom or Kermit is handy
for dialing out to other modems directly without going thru the
Internet. If you are going to use Minicom or Kermit you must find a
phone number to dial that will accept phone calls from a computer
(without using PPP). Perhaps a local library has such a phone number
for its on-line catalog.
Then make sure you are ready to phone. Do you know what serial port
(such as ttyS2) your modem is on? You should have found this out when
you io-irq configured your serial ports. Have you decided what speed
you are going to use for this port? See ``Speed Table'' for a quick
selection or ``What Speed Should I Use with My Modem'' for more
details. If you have no clue of what speed to set, try setting it a
few times faster than the advertised speed of your modem. Also
remember that if you see a menu where an option is "hardware flow
control" and/or "RTS/CTS" or the like, select it. Is a live telephone
cable plugged in to your modem? You may want to connect this cable to
a real telephone to make sure that it can produce a dial tone.
Now you need to select a communication (dialing) program to use to
dial out. Internet dialing programs (using PPP) include wvdial,
pppconfig (Debian), kppp (KDE), and for Gnome: gnome-ppp or "modem
lights". Non-internet dialing programs include: minicom, seyon (X
Window), and kermit. See section ``Communications Programs'' about
some communications programs. Three examples are presented next:
``Dialing Out with wvdial'' ``Dialing Out with Minicom'' and ``Dialing
Out with Kermit''
[1m11.2. Dialing Out with wvdial[0m
Wvdial is a program with not only dials out, but starts PPP and logs
you in to an ISP where you get to the Internet. Wvdial may be
configured during the installation process or by using the program
"wvdialconf". See the man pages for both "wvdialconf" and "wvdial".
However, before using wvdial you must do two other tasks not covered
by the wvdial documentation:
· set up your network on your PC. The old HOWTO, "ISP-Hookup-HOWTO"
has some info on how to do this but fails to mention programs such
as wvdial which replaces "chatscripts".
· configure your browser
[1m11.3. Dialing Out with Minicom[0m
Minicom comes with most Linux distributions. To configure it you
should be the root user. As root, type "minicom -s" to configure.
This will take you directly to the configuration (set-up) menus. This
allows you to use the configuration immediately. If you just type
"minicom" and then configure, you'll need to leave and restart minicom
for the configuration to take effect. Within minicom type ^A to see
the bottom status line. This shows to type ^A Z for help (you've
already typed the ^A so just type z).
Most of the options don't need to be set for just simply dialing out.
To configure you have to supply a few basic items: the name of the
serial port your modem is on such as /dev/ttyS2 and the speed such as
115200. These are set at the serial port menu. Go to it and set
them. Also (if possible) set hardware flow control (RTS/CTS). Then
save them. When typing in the speed, you should also see something
like "8N1" which you should leave alone. It means: 8-bit bytes, No
parity, 1 stop-bit appended to each byte. If you can't find the speed
you want, a lower speed will always work for a test. Exit (hit
return) when done and save the configuration as default (dfl) using
the menu. Unless you've used the -s option when you called minicom,
you'll need to exit minicom and start it again so it can now find the
serial port and initialize the modem.
Now you are ready to dial. But first at the main screen you get after
you first type "minicom" make sure there's a modem there by typing AT
and then hit the <enter> key. It should display OK. If it doesn't,
try typing ATQ0 V1 EI and see if you get OK. If you still don't get
OK, something is wrong and there is no point of trying to dial. Why
you might need to type: ATQ0 V1 E1 is because a modem can be get into
a state where is can't display OK and this should get it out of that
state.
If you got the "OK" go back to help and select the dialing directory.
You may edit it and type in a phone number, etc. into the directory
and then select "dial" to dial it. Alternatively, you may just dial
manually (by selecting "manual" and then type the number at the
keyboard). If it doesn't work, carefully note any error messages and
try to figure out what went wrong.
[1m11.4. Dialing Out with Kermit[0m
You can find the latest version of kermit at
http://www.columbia.edu/kermit/. For example, say your modem was on
ttyS4, and its speed was 115200 bps. You would do the following:
linux# kermit
C-Kermit 6.0.192, 6 Sep 96, for Linux
Copyright (C) 1985, 1996,
Trustees of Columbia University in the City of New York.
Default file-transfer mode is BINARY
Type ? or HELP for help.
C-Kermit>set line /dev/ttyS4
C-Kermit>set carrier-watch off
C-Kermit>set speed 115200
/dev/ttyS4, 115200 bps
C-Kermit>c
Connecting to /dev/ttyS4, speed 115200.
The escape character is Ctrl-\ (ASCII 28, FS)
Type the escape character followed by C to get back,
or followed by ? to see other options.
ATE1Q0V1 ; you type this and then the Enter key
OK ; modem should respond with this
If your modem responds to AT commands, you can assume your modem is
working correctly on the Linux side. Now try calling another modem by
typing:
ATDT7654321
where 7654321 is a phone number. Use ATDP instead of ATDT if you have
a pulse line. If the call goes through, your modem is working.
To get back to the kermit prompt, hold down the Ctrl key, press the
backslash key, then let go of the Ctrl key, then press the C key:
Ctrl-\-C
(Back at linux)
C-Kermit>quit
linux#
This was just a test using the primitive "by-hand" dialing method.
The normal method is to let kermit do the dialing for you with its
built-in modem database and automatic dialing features, for example
using a US Robotics (USR) modem:
linux# kermit
C-Kermit 6.0.192, 6 Sep 1997, for Linux
Copyright (C) 1985, 1996,
Trustees of Columbia University in the City of New York.
Default file-transfer mode is BINARY
Type ? or HELP for help
C-Kermit>set modem type usr ; Select modem type
C-Kermit>set line /dev/ttyS4 ; Select communication device
C-Kermit>set speed 115200 ; Set the dialing speed
C-Kermit>dial 7654321 ; Dial
Number: 7654321
Device=/dev/ttyS4, modem=usr, speed=115200
Call completed.<BEEP>
Connecting to /dev/ttyS4, speed 115200
The escape character is Ctrl-\ (ASCII 28, FS).
Type the escape character followed by C to get back,
or followed by ? to see other options.
Welcome to ... (a welcome message, etc.)
login:
[1m12. Dial-In[0m
[1m12.1. Dial-In Overview[0m
Dial-in is where you set up your PC so that others may dial in to your
PC (at your phone number) and use your PC. Unfortunately some use the
term "dial-in" when what they actually mean is just the opposite:
dial-out.
Dial-in works like this: Someone with a modem dials your telephone
number. Your modem answers the phone ring and connects. Once the
caller is connected, the getty program is notified and starts the
login process for the caller. After the caller has logged in, the
caller then may use your PC. It could be almost as if they were
sitting at your monitor-console.
The caller may use a script to automatically log in. This script will
be of the expect-send type. For example it expects "login:" and then
(after it detects "login:") will send the users login name. It next
expects the password and then sends the password, etc. Then once the
user has been automatically logged in, the /etc/passwd (password file)
might specify that a shell (such as bash) will be started for the
user. Or it might specify that PPP is to start so that the user may
be connected to the Internet. See the PPP-HOWTO for more details.
The program that you use at your PC to handle dialin is called getty
or mgetty. See ``Getty''
An advanced getty program such as mgetty can watch to see if PPP is
started by the PC on the other end. If so, the login prompt would be
skipped, a PPP connection would be made, and login would take place
automatically over the PPP connection.
[1m12.2. What Happens when Someone Dials In ?[0m
Here's a more detailed description of dialin. This all assumes that
you are using either mgetty or uugetty. Agetty is inferior and
doesn't work exactly the same (see ``About agetty'')
For dialin to work, the modem must be listening for a ring and getty
must be running and ready to respond to the call. Your modem is
normally listening for incoming calls, but what it does when it gets a
ring depends on how it's configured. The modem can either
automatically answer the phone or not directly answer it. In the
latter case the modem sends a "RING" message to getty and then getty
tells the modem to answer the ring. In either case, it may be set up
to answer on say the 4th ring. This means that if the call is not for
the modem, one must walk/run to the phone and pick it up manually
before the 4th ring. Then an ordinary conversation can take place on
the telephone. If ons gets to the phone too late one will hear the
high pitched tones of the modem which has answered the call.
Once the modem answers the call it sends tones to the other modem (and
conversely). The two modems negotiate how they will communicate and
when this is completed your modem sends a "CONNECT" message (or the
like) to getty. When getty gets this message, it sends a login prompt
out the serial port. Once a user name is given to this prompt getty
may just call on a program named login to handle the login procedure
from there on. While getty usually starts running at boot-time it
should wait until a connection is made before sending out a "login"
prompt.
Now for more details on the two methods of answering the call. The
first method is where the modem automatically answers the call. In
this case the number of times it will ring before answering is
controlled by the S0 register of the modem. If S0 is set to 3, the
modem will automatically answer on the 3rd ring. If S0 is set to 0
then the modem will only answer the call if getty sends it an "A" (=
Answer) AT command to the modem while the phone is ringing. (Actually
an "ATA" is sent since all modem commands are prefixed by "AT".) This
is the second method of answering, known as "manual" answering, since
the modem itself doesn't do it automatically (but getty does). You
might think it best to utilize the ability of the modem hardware to
automatically answer the call, but it's actually better if getty
answers it "manually".
For the "manual" answer case, getty opens the port at boot-time and
listens. When the phone rings, a "RING" message is sent to the
listening getty. Then if getty wants to answer this ring, it sends
the modem an "A" command. Note that getty may be set to answer only
after say 4 "RING" messages (the 4th ring) similar to the automatic
answer method. The modem then makes a connection and sends a "CONNECT
..." message to getty which then sends a login prompt to the caller.
It's not all quite this simple as there are some special tricks used
to allow dial-out when waiting for a call. See ``Dialing Out while
Waiting for an Incoming Call''
The automatic answer case uses the CD (Carrier Detect aka DCD) wire
from the modem to the serial port to tell when a connection is made.
It works like this: At boot-time getty tries to open the serial port
but the attempt fails since the modem has negated CD (the modem is
idle). Then the getty program waits at the open statement in the
program until a CD signal is raised. When a CD signal arrives
(perhaps hours later) then the port is opened and getty sends the
login prompt. While getty is waiting (sleeping) at the open
statement, other processes can run so it doesn't degrade computer
performance. What actually wakes getty up is an interrupt which is
issued when the CD line from the modem changes its state to on.
You may wonder how getty is able to open the serial port in the
"manual"-answer case since CD may be negated. Well, there's a way to
write a program to force the port to open even if there is no CD
signal raised.
[1m12.3. 56k Doesn't Work for Dialin[0m
If you expect that people will be able to dial-in to you at 56k, it
can't be done unless you have all the following:
1. You have a digital connection to the telephone company such as a
trunkside-T1 or ISDN line
2. You use special digital modems (see ``Digital Modems'')
3. You have a "... concentrator", or the like to interface your
digital-modems to the digital lines of the telephone company.
A "... concentrator" may be called a "modem concentrator" or a
"remote access concentrator" or it could be included in a "remote
access server" (RAS) which includes the digital modems, etc. This
type of setup is used by ISPs (Internet Service Providers).
[1m12.4. Getty[0m
[1m12.4.1. Introduction to Getty[0m
A getty program (including agetty, mgetty, etc.) is what you run for
dialin. You don't need it for dialout. In addition to presenting a
login prompt, it also may help answer an incoming telephone call.
Originally getty was used for logging in to a computer from a dumb
terminal. A major use of it today is for logging in to a Linux system
at a console. There are several different getty programs a few of
which work OK with modems for dialin. The getty program is usually
started either at boot-time or when someone dials in to your computer.
It must be called from the /etc/inittab file. In this file you may
find some examples which you will likely need to edit a bit.
There are four different getty programs to choose from that may be
used with modems for dial-in: mgetty, uugetty, getty_em, and agetty.
A brief overview is given in the following subsections. agetty is the
weakest of the four and it's mainly for use with directly connected
text-terminals. mgetty includes support for fax and voice mail but
uugetty doesn't. But mgetty allegedly lacks a few of the features of
uugetty. getty_em is a simplified version of uugetty. Thus mgetty is
likely your best choice unless you are already familiar with uugetty
(or find it difficult to get mgetty). The syntax for these getty
programs differs, so be sure to check that you are using the correct
syntax in /etc/inittab for whichever getty you use.
In order to see what documentation exists about the various gettys on
your computer, use the "locate" command. Type: locate "*getty*"
(including the quotes may help). Note that many distributions just
call the program getty even though it may actually be agetty, uugetty,
etc. But if you read the man page (type: man getty), it might
disclose which getty it is. This should be the getty program with
path /sbin/getty.
[1m12.4.2. How getty respawns[0m
After you log in you will notice (by using "top", "ps -ax", or
"ptree") that the getty process is no longer running. What happened
to it? Why does getty restart again if your shell is killed? Here's
why.
After you type in your user name, getty takes it and calls the login
program telling it your user name. The getty process is replaced by
the login process. The login process asks for your password, checks
it and starts whatever process is specified in your password file.
This process is often the bash shell. If so, bash starts and replaces
the login process. Note that one process replaces another and that
the bash shell process originally started as the getty process. The
implications of this will be explained below.
Now in the /etc/inittab file, getty is supposed to respawn (restart)
if killed. It says so on the line that calls getty. But if the bash
shell (or the login process) is killed, getty respawns (restarts).
Why? Well, both the login process and bash are replacements for getty
and inherit the signal connections establish by their predecessors.
In fact if you observe the details you will notice that the
replacement process will have the same process ID as the original
process. Thus bash is sort of getty in disguise with the same process
ID number. If bash is killed it is just like getty was killed (even
though getty isn't running anymore). This results in getty
respawning.
When one logs out, all the processes on that serial port are killed
including the bash shell. This may also happen (if enabled) if a
hangup signal is sent to the serial port by a drop of DCD voltage by
the modem. Either the logout or drop in DCD will result in getty
respawning. One may force getty to respawn by manually killing bash
(or login) either by hitting the k key, etc. while in "top" or with
the "kill" command. You will likely need to kill it with signal 9
(which can't be ignored).
[1m12.4.3. About mgetty[0m
mgetty was written as a replacement for uugetty which was in existence
long before mgetty. Both are for use with modems but mgetty is best
(unless you already are committed to uugetty). mgetty may be also
used for directly connected terminals but doesn't have many features
for this purpose. In addition to allowing dialup logins, mgetty also
provides FAX support, auto PPP detection, and caller-id support. It
permits dialing out when mgetty is waiting for an incoming phone call.
There is a supplemental program called vgetty which handles voicemail
for some modems. mgetty documentation is fair (except for voice
mail), and is not supplemented in this HOWTO. To automatically start
PPP one must edit /etc/mgetty/login.conf to use "AutoPPP" (has
example). You can find the latest information on mgetty at
http://www.leo.org/~doering/mgetty/ and
<http://alpha.greenie.net/mgetty/>
[1m12.4.4. About uugetty[0m
getty_ps contains two programs: getty is used for console and
terminal devices, and uugetty for modems. Greg Hankins (former author
of Serial-HOWTO) used uugetty so his writings about it are included
here. See ``Uugetty''.
[1m12.4.5. About getty_em[0m
This is a simplified version of ``uugetty''. It was written by Vern
Hoxie after he became fully confused with complex support files needed
for getty_ps and uugetty.
It is part of the collection of serial port utilities and information
by Vern Hoxie available via ftp from <scicom.alphacdc.com/pub/linux>.
The name of the collection is ``serial_suite.tgz''.
[1m12.4.6. About agetty[0m
This subsection is long since the author tried using agetty for
dialin. agetty is seemingly simple since there are no initialization
files. But when I tried it, it opened the serial port even when there
was no CD signal present. It then sent both a login prompt and the
/etc/issue file to the modem in the AT-command state before a
connection was made. The modem thinks all this an AT command and if
it does contain any "at" strings (by accident) it is likely to
adversely modify your modem profile. Echo wars can start where getty
and the modem send the same string back and forth over and over. You
may see a "respawning too rapidly" error message if this happens. To
prevent this you need to disable all echoing and result codes from the
modem (E0 and Q1). Also use the -i option with agetty to prevent any
/etc/issue file from being sent.
If you start getty on the modem port and a few seconds later find that
you have the login process running on that port instead of getty, it
means that a bogus user name has been sent to agetty from the modem.
To keep this from happening, I had to save my dial-in profile in the
modem so that it become effective at power-on. The other saved
profile is for dial-out. Then any dial-out programs which use the
modem must use a Z, Z0, or Z1 in their init string to initialize the
modem for dial-out (by loading the saved dial-out profile). If the
1-profile is for dial-in you use Z1 to load it, etc. If you want to
listen for dial-in later on, then the modem needs to be reset to the
dial-in profile. Not all dial-out programs can do this reset upon
exit from them.
Thus while agetty may work OK if you set up a dial-in profile
correctly in the modem hardware, it's probably best suited for virtual
consoles or terminals rather than modems. If agetty is running for
dialin, there's no easy way to dial out. When someone first dials in
to agetty, they should hit the return key to get the login prompt.
agetty in the Debian distribution is just named getty.
[1m12.4.7. About mingetty, and fbgetty[0m
mingetty is a small getty that will work only for monitors (the usual
console) so you can't use it with modems for dialin. fbgetty is as
above but supports framebuffers.
[1m12.5. Why "Manual" Answer is Best[0m
The difference between the two ways of answering is exhibited when the
computer happens to be down but the modem is still working. For the
manual case, the "RING" message is sent to getty but since the
computer is down, getty isn't there and the phone never gets answered.
There are no telephone charges when there is no answer. For the
automatic answer case, the modem (which is still on) answers the phone
but no login message is ever sent since the computer is down. The
phone bill runs up as the waiting continues. If the phone call is
toll-free, it doesn't make much difference, although it may be
frustrating waiting for a login prompt that never arrives. mgetty
uses manual answer. Uugetty can do this too by using a configuration
script.
[1m12.6. Dialing Out while Waiting for an Incoming Call[0m
Here's what could go wrong with a simple-minded manual-answer
situation. Suppose another process dials out while getty is listening
for a "RING" message from its modem on the serial wire. Then incoming
bytes for the dial-out process flow from the modem to the serial port.
For example, your modem may send a "CONNECT" message to your serial
port when the dial-out process connects. If getty reads this there's
trouble since reads are destructive reads. Once getty reads it, then
the dial-out process that is expecting "CONNECT" (or something else)
can't read it. Thus the dial-out process is likely to fail.
There's a way to avoid this and here's how mgetty does it. When
mgetty is listing for an incoming call, it doesn't read anything from
the port until it thinks that the characters are for mgetty. Mgetty
monitors the port and if characters arrive, it doesn't read them right
away. Instead, it first checks to see if another process is using the
port. If so, mgetty backs off and closes the port (but the port
remains open for the other process). Thus, if another process dials
out, mgetty doesn't interfere with it. When the other process finally
closes the port, then mgetty resumes "listening". It's a special type
of "listening" that refrains from reading until mgetty believes that
what it will read is for mgetty (hopefully a "RING" message).
When mgetty checks to see if another process is using the port, it
actually checks for valid lockfiles on the port. If the other process
failed to use lockfiles, too bad for it. For more details see the
mgetty documentation: "How mgetty works". For programmers only:
"listening" is actually using the system calls "poll" or "select" to
monitor the port. They are likely also used to monitor the port when
a non-mgetty process is using the port.
Then there's the problem of modem configuration when using mgetty.
Mgetty first sets this configuration when it starts up and uses a
user-specified chat script to do it. So the modem is now configured
not to auto-answer but to send the RING string to mgetty when the
phone rings. Now suppose that while mgetty is waiting for an incoming
call, another program makes and outgoing call and reconfigures the
modem to something bad for mgetty. To prevent this, when mgetty
detects that some other program using the port has exited, mgetty just
exits itself. This results in mgetty starting up anew (respawns per
the /etc/inittab file) and then mgetty reconfigures the modem so that
it's all set up to listen once more for incoming calls.
With auto-answer (not normally used by mgetty), getty is waiting for
CD to be raised so that it can open the port. One may dial out, but
once a connection is made, the modem's CD is raised. If getty were to
then read the port it would eat the characters intended to be read by
the dial-out connection. While agetty will have this problem, it's
claimed that uugetty will check lockfiles before reading (similar to
mgetty).
[1m12.7. Ending a Dial-in Call[0m
There are two major ways to end a dial-in call. The caller may either
logout or just hang up. For the hangup case see ``Caller hangs up''
[1m12.7.1. Caller logs out[0m
When the call is over, the normal way to end the connection is for the
remote user to log out. This should result in the dial-in PC hanging
up the phone line as will be explained shortly. Note that this
behavior is not what normally happens when one logs out from a PC
(when not using a modem). In this case, the user logs out and
immediately gets a login prompt as an invitation to log in again. But
a remote user that types "logout" gets hung up on, and must redial if
s/he wants to log in again. If there was no hang-up when the user
logged out, the connection would be maintained, and not give anyone
else the opportunity to login.
Logging out by the remote user of your dial-in PC will kill the shell
that the remote user was using on your dial-in PC. Now, since there
is nothing running on this port anymore, the port closes and sends a
hangup signal to the modem by negating DTR. This will only happen if
stty -a shows hupcl (default). hupcl = Hang UP on CLose => drop DTR
(the "hang up" signal) when the last program running on this port is
closed). But normally, when the shell is killed it's like getty was
killed and getty will respawn (since it's set this way in
/etc/inittab). This will almost immediately open the port again and
raise DTR. So DTR is said to wink (drop only for only a small
fraction of a second and then reassert itself). With modern fast
computers, this wink would be too short to be recognized by the modem
so the serial driver is supposed to make this wink longer (provided
stty has hupcl set, and provided ...). But there was a complaint in
2003 that it's not long enough.
The dial-in PC modem getting the hangup (negated DTR signal) will then
hang up the phone line (provided the modem has been configured to do
this --see below). The modem should then be ready to answer any new
incoming calls. For mgetty, if there is a chat-script to initialize
the modem and possibly reset the modem will happen also. If the modem
didn't hang up due to too short of a DTR wink, then a newly spawned
getty might be able to hang up. mgetty itself creates a long DTR wink
when it starts up to hang up the modem. It's claimed that making a
respawned getty clean up the mess (the modem still online) left by the
previous call, is not the right way to handle this.
When setting up mgetty, one may use a chat-script with the code
sequence +++ to the modem to put it into AT command mode if DTR didn't
work. The +++ must have both an initial and final minimal time delay.
Once in AT command mode, a hangup command (H0) may be sent to the
modem as well as other AT commands. One may have things set up to use
both this method and the DTR method and so that if one method should
fail, the other one will hopefully work. If the PC fails to
successfully signal the modem when a logout happens (or fails to use
the +++ escape when restarting getty), then the modem is apt to remain
in on-line mode and no more incoming calls can be received. It's
claimed that this might be a security risk.
[1m12.7.2. When DTR drops (is negated)[0m
When DTR (the "hang-up" signal when negated) is dropped (negated),
what the modem does depends on the value of the &D option in the
modem's profile. If it's &D0 nothing at all happens (the modem
ignores the negation of DTR). Here's what happens when the computer
drops DTR:
&D2: The modem will hang up and go into AT command mode (off-line) to
wait for the next call. Except that it will not be able to
automatically answer the phone until DTR is raised again. But since
mgetty automatically respawns (if so set in /etc/inittab) then mgetty
will immediately restart after a logout and this will raise DTR. So
what happens when someone logs out is that DTR only is negated for a
fraction of a second (winks) before it gets raised again. During this
wink, the DTR must be negated for at least the time specified by
register S25, otherwise the modem will not hang up.
&D3: or S13 = 1. In this case the modem does a hard reset when DTR
drops: It hangs up and restores the saved profile as specified by &Y.
It should now be in the same state it was in when first powered on.
But mgetty may have a chat script which will send the modem an init
string and thus change the profile again. Since these two changes in
profile happen at about the same time, could this be a problem (known
as "race conditions").
The S25 limit may have no effect so even a very short DTR "wink" is
detected. Another brand of modem says the S25 limit is still valid.
Thus &D3 is a stronger "reset" than &D2 which doesn't restore the
saved profile and could require a longer wink to work.
Under favorable conditions, either &D3 or &D2 should work OK. It's
reported that for a few modems, only &D2 works OK. Could this be
related to a possible race condition mentioned above if &D3 is used?
[1m12.7.3. Caller hangs up[0m
Instead of logging out the normal way, a caller may just hang up (by
closing the "terminal" program s/he's using, etc). This results in a
lost connection and of course a loss of carrier. Other problems could
also cause a loss of carrier. The modem hangs up and waits for the
next call. Except that there is no mgetty running yet to start the
login process.
Here's how getty gets started again: The loss of carrier should
negate the CD signal sent by the modem to the serial port (provided
&C1 has been set). When the PC's serial port gets the dropped CD
signal it should kill the shell, provided clocal is negated (-clocal)
and then getty should respawn. mgetty raises clocal when it starts.
Does it later drop clocal?
This paragraph is about other things that happen but do nothing. Only
the curious need read it. When the shell is killed, a DTR wink is
sent to the modem but since the modem is not on-line anymore and has
already hung up due to lost carrier, the modem ignores the drop of
DTR. The loss of carrier also negates the DSR signal sent by the
modem to the serial port (provided &S1 or &S2 is set) but this signal
is ignored (by Linux). The "NO CARRIER" result code should be
generated by the modem but where does it go to ?
[1m12.8. Dial-in Modem Configuration[0m
The getty programs have a provision for sending an init string to the
modem to configure it. But you may need to edit it. Another method
is to save a suitable init string inside the modem (see ``Init
Strings: Saving and Recalling'' for how to save it in the modem).
The configuration for dial-in depends both on the getty you use and
perhaps on your modem. If you can't find suggested configurations in
other documentation here are some hints using Hayes AT commands:
· &C1 Make the CD line to the serial port track the actual state of
the carrier (CD raised only when there's carrier). Getty_em
requires &C0 (CD always raised)
· &D3 Do a hard reset of the modem when someone logs out (or hangs
up). For some modems it's reported that &D2 is required since they
can't tolerate a hard reset ??
· E0 Don't echo AT commands back to the serial port. This is a must
for agetty. Some suggest E1 (echo AT commands) for mgetty. For
dial-out you want E1 so you can see what was sent.
· &K3 Use hardware flow control
· Q0 Echo results words (such as CONNECT). Most gettys use them.
But it's reported an AT&T version of uugetty and agetty require Q2
(no result words for dial-in).
· S0=? mgetty suggests S0=0 (manual answer) but you give the number
of rings on the mgetty command line. If you set S0=3 the modem
will auto-answer on the 3rd ring, etc. Agetty uses auto-answer.
So does uugetty (usually).
· V1 Display results (such as CONNECT) in words (and not in code)
· X4 Check for dialtone and busy signal
[1m12.9. Callback[0m
Callback is where someone first dials in to your modem. Then, you get
a little info from the caller and then call it right back. Why would
you want to do this? One reason is to save on telephone bills if you
can call the caller cheaper than the caller can call you. Another is
to make sure that the caller really is who it claims to be. If a
caller calls you and claims to be calling from its usual phone number,
then one way to verify this is to actually place a new call to that
number.
There's a program for Linux called "callback" that works with mgetty.
It's at <ftp://ftp.rug.nl/contrib/frank/software/linux/callback/>
Step-by-step instructions on how someone installed it (and PPP) is at
<http://www.stokely.com/unix.serial.port.resources/callback.html>
[1m12.10. Distinctive Ring[0m
"Distinctive ring" is where you want the modem to answer phone calls
only for certain types of rings like long, short, long, short, etc.
To do this, you first need a modem that supports distinctive ring.
The Netcomm Roadster modem can be set with an AT command to do the
following, for example: It will send to mgetty: DROF=14 DRON=4 RING
DROF=4 DRON=2 RING ... meaning that there is a 1.4 seconds of initial
silence (DROF=14) followed by .4 seconds of ringing (DRON=4) etc.
RING is also reported after each ring. Note that the modem can't be
set to answer a certain type of ring, it only informs the program
listening on the serial port (such as mgetty) what the ring sequence
is. Then if the program likes the sequence, it sends an AT command to
the modem to answer the call. Unfortunately, mgetty doesn't recognize
such ring sequences but there's a workaround that may work.
Mgetty only waits for a "RING" and will ignore the DRON and DROF
(Distinctive Ring OFf) words. For the Netcomm Roadster modem, you can
set the delay between sending DRON= and RING. For example you could
set a delay of 2.0 seconds. However, if within this 2.0 second period
another actual ring occurs, the modem cancels the delayed RING message
and never sends it. So you might be able to set this delay so the the
calls you don't want the modem to answer never send a RING message to
mgetty. But for the calls you want mgetty to answer, you get the
interval between rings to be long enough so that "RING" is sent to
mgetty and mgetty answers the call. This workaround is not always
feasible, especially if the telephone company doesn't give you much
choice of distinctive rings. Will the above work for other modems
that support distinctive ring?
For the above modem, the AT command: AT+VDR=1,24 sets the above delay
for 2.4 seconds. You can put this in an "init-chat" parameter in
mgetty.config.
[1m12.11. Voice Mail[0m
Voice mail is like an answering machine run by a computer. To do this
you must have a modem that supports "voice" and supporting software.
Instead of storing the messages on tape, they are stored in digital
format on a hard-drive. When a person phones you, they hear a
"greeting" message and can then leave a message for you. More
advanced systems would have caller-selectable mail boxes and caller-
selectable messages to listen to. Free software is available in Linux
for simple answering, but doesn't seem to be available yet for the
more advanced stuff.
I know of two different voicemail packages for Linux. One is a very
minimal package (see ``Voicemail Software''). The other, more
advanced, but currently poorly documented, is vgetty. It's an
optional addition to the well documented and widely distributed mgetty
program. It supports ZyXEL-like voice modem commands. In the Debian
distribution, you must get the mgetty-voice package in addition to the
mgetty package and mgetty-doc package.
[1m12.12. Simple Manual Dial-In[0m
This is really doing it manually! It doesn't even permit the caller
to login but the caller may "chat" with you, etc. It's a way to
answer a call without bothering to edit any configuration files for
dial-in or enabling getty. To do it you run a terminal program such
as minicom. Make sure it's connected to your modem by typing "AT
<enter>" and expect "OK". Then wait for the call. Then you really
answer the call manually by typing "ATA" when the phone is ringing.
This doesn't run getty and the caller can't login. But if the caller
is calling in with a terminal program they may type a message to your
screen (and conversely). You both may send files back and forth by
using the commands built into the terminal programs (such as minicom).
Another way to answer such a call would be to type say "ATS0=3" just
before the call comes in to enable the modem to auto-answer on the
third ring.
This is one way to crudely transfer files with someone on a MS Windows
PC who uses HyperTerminal or Terminal (for Windows 3.x or DOS). These
two MS programs are something like minicom. Using this simple manual
method (for Linux-to-Linux or MS-to-Linux) requires two people to be
present, one one each end of the phone line connection running a
terminal communications program. Be warned that if both people type
at the same time it's chaos. It's a "last resort" way to transfer
files between any two people that have PCs (either Linux or MS
Windows). It could also be used for testing your modem or as a
preliminary test before setting up dial-in.
[1m12.13. Complex GUI Dial-In, VNC[0m
At the opposite extreme to the simple (but labor intensive) manual
dial-in described above, is one that results in GUI graphical
interface to the Linux PC. This generally requires that a network
running TCP/IP protocol exist between the two computers. One way to
get such a "network" is to dial-out to a PC set for dial-in and then
run PPP on the phone line. PPP will use TCP/IP protocol encapsulated
inside the PPP packets. Both sides must run PPP and mgetty can be
configured to start PPP as soon as the caller does. The caller may
use a PPP-dialer program just like they were dialing an ISP. Programs
such as wvdial, eznet, or chat scripts should do it.
Instead of this tiny network over a phone connection a much larger
network (the entire world) is reached via an ISP. For their lowest-
rate service many of them use proxy servers that will not give you
access to the ports you need to use. Even if they don't use proxy
servers, the IP address they give you is only temporary for the
session, so you'll need to email this IP to whomever wants to reach
you. If you get a more expensive ISP service, then you can avoid
these problems.
One way to get a GUI interface from the remote PC is to run the GPLed
program: Virtual Network Computer (VNC) from AT&T. It has a server
part which you run on your Linux PC for dial-in and a viewer (client)
part used for dial-out. Neither of these actually does any dialing or
login but assumes that you have a network already set up. The VNC
server has an X-server built in and may use Linux's twm window
manager. See the article on VNC in Linux Magazine:
<http://www.linux-mag.com/2000-11/desktop_03.html>. The AT&T site for
VNC is: <http://www.uk.research.att.com/vnc/>.
With VNC one can also connect to remote Windows PCs, get the Windows
GUI on a Linux PC, and run Windows programs on the remote Windows PC.
Of course the Windows PC must be running VNC (as a server).
Obviously, a GUI connection over a modem will be slower than a text-
only connection especially if you run KDE or GNOME or want 16-bit
color.
[1m12.14. Interoperability with MS Windows[0m
Once you have dial-in set up, others may call in to you using minicom
(or the like) from Unix-like systems. From MS Windows one may call
you using "HyperTerminal (or just "Terminal" in Windows 3.1 or DOS).
If in Windows one wants to use dial-up with a network protocol over
the phone line it's called "Dial-up Networking". But it probably will
not be able to communicate with Linux. For setting up such dial-in in
Windows one clicks on "server" while dial-out is the "client. Such
dial-in is often called "remote control" meaning that the caller can
use your PC, run programs on it, and thus control it remotely.
While it's easy to call in to a text-based Linux system from MS
Windows, it's not so easy the other way around (partly because Windows
is not text-based and would need to put the caller into DOS where
files wouldn't be protected like they are in Linux.
However Windows "Dial-up Networking" can establish a dial-in provided
the caller uses certain network protocols over the phone line: MS's or
Novel's (two protocols not liked by Linux). So if someone with
Windows enables their Dial-up networking server in Windows 98, you
can't just dial in directly to it from Linux. This type of dial-in
doesn't permit the caller to run most of the programs on the host like
Linux does. It's called "remote access" and one may transfer files,
use the hosts printer, access databases, etc. Is there some way to
interface to Dial-up Networking from Linux??
It is possible for two people to crudely chat and send files using
Minicom on the Linux end and HyperTerminal on the Windows end. It's
all done manually by two live persons, one on each end of the phone
connection. See ``Simple Manual Dial-In''.
At the opposite extreme, one would like to run a dial-in so that the
person calling would get a GUI interface. For that a network protocol
is normally used. It's possible using PC Anywhere for Windows or VNC
for both Linux and Windows. But PC Anywhere doesn't seem to talk to
Linux ?? Other Window programs for "remote control" include Laplink,
Co-Session, and Microcom. Do any such programs support Linux besides
VNC ??
[1m13. Uugetty for Dial-In (from the old Serial-HOWTO)[0m
Be aware that you could use mgetty as a (better?) alternative to
uugetty. mgetty is newer and more popular than uugetty. See
``Getty'' for a brief comparison of these 2 gettys.
[1m13.1. Installing getty_ps[0m
Since uugetty is part of getty_ps you'll first have to install
getty_ps. If you don't have it, get the latest version from
metalab.unc.edu:/pub/Linux/system/serial. In particular, if you want
to use high speeds (57600 and 115200 bps), you must get version 2.0.7j
or later. You must also have libc 5.x or greater.
By default, getty_ps will be configured to be Linux FSSTND (File
System Standard) compliant, which means that the binaries will be in
/sbin, and the config files will be named /etc/conf.{uu}getty.ttyS[4mN[24m.
This is not apparent from the documentation! It will also expect lock
files to go in /var/lock. Make sure you have the /var/lock directory.
If you don't want FSSTND compliance, binaries will go in /etc, config
files will go in /etc/default/{uu}getty.ttyS[4mN[24m, and lock files will go
in /usr/spool/uucp. I recommend doing things this way if you are
using UUCP, because UUCP will have problems if you move the lock files
to where it isn't looking for them.
getty_ps can also use syslogd to log messages. See the man pages for
syslogd(1) and syslog.conf(5) for setting up syslogd, if you don't
have it running already. Messages are logged with priority LOG_AUTH,
errors use LOG_ERR, and debugging uses LOG_DEBUG. If you don't want
to use syslogd you can edit tune.h in the getty_ps source files to use
a log file for messages instead, namely /var/adm/getty.log by default.
Decide on if you want FSSTND compliance and syslog capability. You
can also choose a combination of the two. Edit the Makefile, tune.h
and config.h to reflect your decisions. Then compile and install
according to the instructions included with the package.
[1m13.2. Setting up uugetty[0m
With uugetty you may dial out with your modem while uugetty is
watching the port for logins. uugetty does important lock file
checking. Update /etc/gettydefs to include an entry for your modem.
For help with the meaning of the entries that you put into
/etc/gettydefs, see the "serial_suite" collected by Vern Hoxie. How
to get it is in section See``About getty_em''. When you are done
editing /etc/gettydefs, you can verify that the syntax is correct by
doing:
linux# getty -c /etc/gettydefs
[1m13.2.1. Modern Modems[0m
If you have a 9600 bps or faster modem with data compression, you can
lock your serial port to one speed. For example:
# 115200 fixed speed
F115200# B115200 CS8 # B115200 SANE -ISTRIP HUPCL #@S @L @B login: #F115200
If you have your modem set up to do RTS/CTS hardware flow control, you
can add CRTSCTS to the entries:
# 115200 fixed speed with hardware flow control
F115200# B115200 CS8 CRTSCTS # B115200 SANE -ISTRIP HUPCL CRTSCTS #@S @L @B login: #F115200
[1m13.2.2. Old slow modems[0m
If you have a slow modem (under 9600 bps) Then, instead of one line
for a single speed, your need several lines to try a number of speeds.
Note that these lines are linked to each other by the last "word" in
the line such as #4800. Blank lines are needed between each entry.
Are the higher modem-to-serial_port speeds in this example really
needed for a slow modem ?? The uugetty documentation shows them so
I'm not yet deleting them.
# Modem entries
115200# B115200 CS8 # B115200 SANE -ISTRIP HUPCL #@S @L @B login: #57600
57600# B57600 CS8 # B57600 SANE -ISTRIP HUPCL #@S @L @B login: #38400
38400# B38400 CS8 # B38400 SANE -ISTRIP HUPCL #@S @L @B login: #19200
19200# B19200 CS8 # B19200 SANE -ISTRIP HUPCL #@S @L @B login: #9600
9600# B9600 CS8 # B9600 SANE -ISTRIP HUPCL #@S @L @B login: #4800
4800# B4800 CS8 # B4800 SANE -ISTRIP HUPCL #@S @L @B login: #2400
2400# B2400 CS8 # B2400 SANE -ISTRIP HUPCL #@S @L @B login: #1200
1200# B1200 CS8 # B1200 SANE -ISTRIP HUPCL #@S @L @B login: #115200
[1m13.2.3. Login Banner[0m
If you want, you can make uugetty print interesting things in the
login banner. In Greg's examples, he has the system name, the serial
line, and the current bps rate. You can add other things:
@B The current (evaluated at the time the @B is seen) bps rate.
@D The current date, in MM/DD/YY.
@L The serial line to which uugetty is attached.
@S The system name.
@T The current time, in HH:MM:SS (24-hour).
@U The number of currently signed-on users. This is a
count of the number of entries in the /etc/utmp file
that have a non-null ut_name field.
@V The value of VERSION, as given in the defaults file.
To display a single '@' character, use either '\@' or '@@'.
[1m13.3. Customizing uugetty[0m
There are lots of parameters you can tweak for each port you have.
These are implemented in separate config files for each port. The
file /etc/conf.uugetty will be used by [4mall[24m instances of uugetty, and
/etc/conf.uugetty.ttyS[4mN[24m will only be used by that one port. Sample
default config files can be found with the getty_ps source files,
which come with most Linux distributions. Due to space concerns, they
are not listed here. Note that if you are using older versions of
uugetty (older than 2.0.7e), or aren't using FSSTND, then the default
file will be /etc/default/uugetty.ttyS[4mN[24m. Greg's
/etc/conf.uugetty.ttyS3 looked like this:
# sample uugetty configuration file for a Hayes compatible modem to allow
# incoming modem connections
#
# line to initialize
INITLINE=ttyS3
# timeout to disconnect if idle...
TIMEOUT=60
# modem initialization string...
# format: <expect> <send> ... (chat sequence)
INIT="" AT\r OK\r\n
WAITFOR=RING
CONNECT="" ATA\r CONNECT\s\A
# this line sets the time to delay before sending the login banner
DELAY=1
#DEBUG=010
Add the following line to your /etc/inittab, so that uugetty is run on
your serial port, substituting in the correct information for your
environment - run-levels (2345 or 345, etc.) config file location,
port, speed, and default terminal type:
S3:2345:respawn:/sbin/uugetty -d /etc/default/uugetty.ttyS3 ttyS3 F115200 vt100
Restart init:
linux# init q
For the speed parameter in your /etc/inittab, you want to use the
highest bps rate that your modem supports.
Now Linux will be watching your serial port for connections. Dial in
from another machine and login to you Linux system.
uugetty has a lot more options, see the man page for uugetty) (often
just called getty) for a full description. Among other things there
is a scheduling feature, and a ringback feature.
[1m14. What Speed Should I Use with My Modem?[0m
By "speed" we really mean the "data flow rate" but almost everybody
incorrectly calls it speed. For all modern modems you have no choice
of the speed that the modem uses on the telephone line since it will
automatically choose the highest possible speed that is feasible under
the circumstances. If one modem is slower than the other, then the
faster modem will operate at the slower modem's speed. On a noisy
line, the speed will drop still lower.
While the above speeds are selected automatically by the modems you do
have a choice as to what speed will be used between your modem and
your computer (PC-to-modem speed). This is sometimes called "DTE
speed" where "DTE" stands for Data Terminal Equipment (Your computer
is a DTE.) You need to set this speed high enough so this part of the
signal path will not be a bottleneck. The setting for the DTE speed
is the maximum speed of this link. Most of the time it will likely
actually operate at lower speeds.
For an external modem, DTE speed is the speed (in bits/sec) of the
flow over the cable between you modem and PC. For an internal modem,
it's the same idea since the modem also emulates a serial port. It
may seem ridiculous having a speed limit on communication between a
computer and a modem card that is directly connected inside the
computer to a much higher speed bus. But it's usually that way since
the modem card probably includes a dedicated serial port which does
have speed limits (and settable speeds). However, some software
modems have no such speed limits.
[1m14.1. Speed and Data Compression[0m
What speed do you choose? If it were not for "data compression" one
might try to choose a DTE speed exactly the same as the modem speed.
Data compression takes the bytes sent to the modem from your computer
and encodes them into a fewer number of bytes. For example, if the
flow (speed) from the PC to the modem was 20,000 bytes/sec (bps) and
the compression ratio was 2 to 1, then only 10,000 bytes/sec would
flow over the telephone line. Thus for a 2:1 compression ratio you
would need to set the DTE speed to double the maximum modem speed on
the phone line. If the compression ratio were 3 to 1 you would need
to set it 3 times faster, etc.
[1m14.2. Where do I Set Speed ?[0m
This DTE (PC-to-modem) speed is normally set by a menu in your
communications program or by an option given to the getty command if
someone is dialing in. You can't set the DCE modem-to-modem speed
since this is set automatically by the modem to the highest feasible
speed after negotiation with the other modem. Well, actually you can
set the modem-to-modem speed with the S37 register but you shouldn't
do it. If the two modems on a connection were to be set this way to
different speeds, then they couldn't communicate with each other.
[1m14.3. Can't Set a High Enough Speed[0m
[1m14.3.1. Speeds over 115.2k[0m
The top speed of 115.2k has been standard since the mid 1990's. But
by the year 2000, most new serial ports supported higher speeds of
230.4k and 460.8k. Some also support 921.6k. Unfortunately Linux
seldom uses these speeds due to lack of drivers. Thus such ports
behave just like 115.2k ports unless the higher speeds are enabled by
special software. To get these speeds you need to compile the kernel
with special patches or use modules until support is built into the
kernel's serial driver.
Unfortunately serial port manufacturers never got together on a
standard way to support high speeds, so the serial driver needs to
support a variety of hardware. Once high speed is enabled, a standard
way to choose it is to set baud_base to the highest speed with
setserial (unless the serial driver does this for you). The software
will then use a divisor of 1 to set the highest speed. All this will
hopefully be supported by the Linux kernel sometime in 2003.
A driver for the w83627hf chip (used on many motherboards such as the
Tyan S2460) is at <https://www.muru.com/linux/w83627hf/>
A non-standard way that some manufacturers have implemented high speed
is to use a very large number for the divisor to get the high speed.
This number isn't really a divisor at all since it doesn't divide
anything. It's just serves as a code number to tell the hardware what
speed to use. In such cases you need to compile the kernel with
special patches.
One patch to support this second type of high-speed hardware is called
shsmod (Super High Speed Mode). There are both Windows and Linux
versions of this patch. See <http://www.devdrv.com/shsmod/>. There
is also a module for the VIA VT82C686 chip
<http://www.kati.fi/viahss/>. Using it may result in buffer overflow.
For internal modems, only a minority of them advertise that they
support speeds of over 115.2k for their built-in serial ports. Does
shsmod support these ??
[1m14.3.2. How speed is set in hardware: the divisor and baud_base[0m
Speed is set by having the serial port's clock change frequency. But
this change happens not by actually changing the frequency of the
oscillator driving the clock but by "dividing" the clock's frequency.
For example, to divide by two, just ignore every other clock tick.
This cuts the speed in half. Dividing by 3 makes the clock run at 1/3
frequency, etc. So to slow the clock down (meaning set speed), we
just send the clock a divisor. It's sent by the serial driver to a
register in the port. Thus speed is set by a divisor.
If the clock runs at a top speed of 115,000 bps (common), then here
are the divisors for various speeds (assuming a maximum speed of
115,200): 1 (115.2k), 2 (57.6k), 3 (38.4k), 6 (19.2k), 12 (9.6k), 24
(4.8k), 48 (2.4k), 96 (1.2k), etc. The serial driver sets the speed
in the hardware by sending the hardware only a "divisor" (a positive
integer). This "divisor" divides the "maximum speed" of the hardware
resulting in a slower speed (except a divisor of 1 obviously tells the
hardware to run at maximum speed).
There are exceptions to the above since for certain serial port
hardware, speeds above 115.2k are set by using a very high divisor.
Keep that exception in mind as you read the rest of this section.
Normally, if you specify a speed of 115.2k (in your communication
program or by stty) then the serial driver sets the port hardware to
divisor 1 which sets the highest speed.
Besides using a very high divisor to set high speed, the conventional
way to do it is as follows: If you happen to have hardware with a
maximum speed of say 230.4k (and the 230.4k speed has been enabled in
the hardware), then specifying 115.2k will result in divisor 1. For
some hardware this will actually give you 230.4k. This is double the
speed that you set. In fact, for any speed you set, the actual speed
will be double. If you had hardware that could run at 460.8k then the
actual speed would be quadruple what you set. All the above assumes
that you don't use "setserial" to modify things.
[1m14.3.3. Setting the divisor, speed accounting[0m
To correct this accounting (but not always fix the problem) you may
use "setserial" to change the baud_base to the actual maximal speed of
your port such as 230.4k. Then if you set the speed (by your
application or by stty) to 230.4k, a divisor of 1 will be used and
you'll get the same speed as you set.
If you have very old software which will not allow you to tell it such
a high speed (but your hardware has it enabled) then you might want to
look into using the "spd_cust" parameter. This allows you to tell the
application that the speed is 38,400 but the actual speed for this
case is determined by the value of "divisor" which has also been set
in setserial. I think it best to try to avoid using this kludge.
There are some brands of UARTs that uses a very high divisor to set
high speeds. There isn't any satisfactory way to use "setserial" (say
set "divisor 32770") to get such a speed since then setserial would
then think that the speed is very low and disable the FIFO in the
UART.
[1m14.3.4. Crystal frequency is higher than baud_base[0m
Note that the baud_base setting is usually much lower than the
frequency of the crystal oscillator since the crystal frequency of say
1.8432 MHz is divided by 16 in the hardware to get the actual top
speed of 115.2k. The reason the crystal frequency needs to be higher
is so that this high crystal speed can generate clock ticks to take a
number of samples of each bit to determine if it's a 1 or a 0.
Actually, the 1.8432 MHz "crystal frequency" may be obtained from a
18.432 MHz crystal oscillator by dividing by 10 before being fed to
the UART. Other schemes are also possible as long as the UART
performs properly.
[1m14.4. Speed Table[0m
It's best to have at least a 16650 UART for a 56k modem but few modems
or serial ports provide it. Second best is a 16550 that has been
tweaked to give 230,400 bps (230.4 kbps). Most people still use a
16550 that is only 115.2 kbps but it's claimed to only slow down
thruput by a few percent (on average). This is because a typical
compression ratio is 2 to 1 and for downloading compressed files
(packages) it's 1 to 1. There's no degradation for these cases. Here
are some suggested speeds to set your serial line if your modem speed
is:
· 56k (V.92): use 115.2 kbps or 230.4 kbps (best)
· 56k (V.90): use 115.2 kbps or 230.4 kbps (best)
· 33.6k (V.34bis): use 115.2 kbps
· 28.8k (V.34): use 115.2 kbps
· 14.4k (V.32bis): use 57600 bps
· 9.6k (V.32): use 38400 bps
· slower than a 9600 bps (V.32) modem: Set the speed to the same
speed as the modem (unless you have data compression).
All the above speeds may use V.42bis data compression and V.42 error
correction. If data compression is not used then the speed may be set
lower so long as it's above the modem speed.
[1m15. Communications Programs And Utilities[0m
While PPP is used for Internet access you also need a dialer program
(or script) that will dial a phone number and then start PPP once a
connection is made. When the other side answers the phone, then three
things happen: a modem connection is established (CONNECT), PPP is
started at both ends, and you get logged in automatically. The exact
sequence of the last 2 events may vary. Dialer programs for ppp
include wvdial, chap scripts, kppp, RP3 (front end to wvdial and
ifup), gnome-ppp, and "modem lights" (Gnome). Linuxconf configures
some dialers.
There are also older dialer programs which can dial out (via a modem)
but don't connect to the Internet. Instead, you get connected to a
computer somewhere that puts a text image on your screen. This was
much used in the past to connect to Bulletin Boards. See ``PCs and
BBSs'' Today, it might be used to connect to a remote computer that
you may login to (including a PC at home). Programs for this are:
minicom (the most popular), Seyon (X-Windows only) and Kermit. Some
people have likely also used these programs for dialing out with ppp
for the Internet but it's not what they were originally designed for.
[1m15.1. Minicom vs. Kermit[0m
Minicom is only a communications program while Kermit is both a
communications program and a file transfer protocol. But one may use
the Kermit protocol from within Minicom (provided one has Kermit
installed on one's PC). Minicom is menu based while Kermit is command
line based (interactive at the special Kermit prompt). While the
Kermit program is free software, the documentation is not all free.
There is no detailed manual supplied and it is suggested that you
purchase a book as the manual. However Kermit has interactive online
help which tells all but lacks tutorial explanations for the beginner.
Commands may be put in a script file so you don't have to type them
over again each time. Kermit (as a communications program) is more
powerful than Minicom.
Although all Minicom documentation is free, it's not as extensive as
Kermit's. In my opinion it's easier to set up Minicom, there is less
to learn, and you can still use kermit from within Minicom. But if
you want to write a script for automatically doing file transfers,
etc. Kermit is better.
g-kermit is a gpled kermit which has no dialout capabilities.
[1m15.2. List of Communication Software[0m
Here is a list of some communication software you can choose from, If
they didn't come with your distribution they should be available via
FTP. I would like comparative comments on the dialout programs. Are
the least popular ones obsolete?
[1m15.2.1. Least Popular Dialout[0m
· ecu - a communications program
· pcomm - procomm-like communications program with zmodem
· xc - xcomm communication package
[1m15.2.2. Most Popular Dialout[0m
· PPP dialers for getting on the internet: wvdial, eznet, chat, pon
(uses chat),
· minicom - telix-like communications program. Can work with
scripts, zmodem, kermit
· C-Kermit <http://www.columbia.edu/kermit/> - portable, scriptable,
serial and TCP/IP communications including file transfer,
character-set translation, and zmodem support
· seyon - X based communication program
[1m15.2.3. Fax[0m
By using a fax program, you may use most modems to send faxes. In
this case you dial out directly and not via ppp and an ISP. You also
pay any long-distance telephone charges. email is more efficient.
· efax is a small fax program
· hylafax is a large fax program based on the client-server model.
· mgetty+fax handles fax stuff and login for dial-ins
· A fax protocol tutorial
<http://www.iec.org/online/tutorials/vfoip/topic08.html>
[1m15.2.4. Voicemail Software[0m
· vgetty is an extension to mgetty that handles voicemail for some
modems. It should come with recent releases of mgetty.
· VOCP <http://vocp.sourceforge.net/>is a "complete voice messaging"
system for Linux.
[1m15.2.5. Dial-in (uses getty)[0m
· mgetty+fax is for modems and is well documented (except for
voicemail as of early 1999). It also handles fax stuff and
provides an alternative to uugetty. It's incorporating voicemail
(using vgetty) features. See ``About mgetty''
· uugetty is also for modems. It comes as a part of the ps_getty
package. See ``About getty_ps''
[1m15.2.6. Network Connection[0m
· ser2net
· sredird
[1m15.2.7. Other[0m
· callback is where you dial out to a remote modem and then that
modem hangs up and calls you back (to save on phone bills).
· xringd listens for rings and detects inter-ring times etc.
· SLiRP and term provide a PPP-like service that you can run in user
space on a remote computer with a shell account. See ``term and
SLiRP'' for more details
· ZyXEL is a control program for ZyXEL U-1496 modems. It handles
dialin, dialout, dial back security, FAXing, and voice mailbox
functions.
· SLIP and PPP software can be found at
ftp://metalab.unc.edu/pub/Linux/system/network/serial/.
· Other things can be found on
ftp://metalab.unc.edu/pub/Linux/system/serial and
ftp://metalab.unc.edu/pub/Linux/apps/serialcomm or one of the many
mirrors. These are the directories where serial programs are kept.
[1m15.3. SLiRP and term[0m
SLiRP and term are programs which are of use if you only have a dial-
up shell account on a Unix-like machine and want to get the equivalent
of a PPP account (or the like) without being authorized to have it
(possibly because you don't want to pay extra for it, etc.). SLiRP is
more popular than term which is almost obsolete.
To use SLiRP you install it in your shell account on the remote
computer. Then you dial up the account and run SLiRP on the remote
and PPP on your local PC. You now have a PPP connection over which
you may run a web browser on your local PC such as Netscape, etc.
There may be some problems as SLiRP is not as good as a real PPP
account. Some accounts may provide SLiRP since it saves on IP
addresses (You have no IP address while using SLiRP).
term is something like SLiRP only you need to run term on both the
local and remote computer. There is no PPP on the phone line since
term uses its own protocol. To use term from your PC you need to use
a term-aware version of ftp to do ftp, etc. Thus it's easier to use
SLiRP since the ordinary version of ftp works fine with SLiRP. There
is an unmaintained Term HOWTO.
[1m15.4. MS Windows[0m
If you want someone who uses MS Windows to dial in to your Linux PC
then if they use:
· Windows 3.x: use Terminal
· Windows 95/98/2000: use HyperTerminal
Third party dial-out programs include HyperTerminal Private Edition.
[1m16. Two Modems (Modem Doubling)[0m
[1m16.1. Introduction[0m
By using two modems at the same time, the flow of data can be doubled.
It takes two modems and two phone lines. There are two methods of
doing this. One is "modem bonding" where software at both ends of the
modem-to-modem connection enables the paired modems to work like a
single channel.
The second method is called "modem teaming. Only one end of the
connection uses software to make 2 different connections to the
internet. Then when a file is to be downloaded, one modem gets the
first half of the file. The second modems simultaneously gets the
last half of the same file by pretending that it's resuming a download
that was interrupted in the middle of the file. Is there any modem
teaming support in Linux ??
[1m16.2. Modem Bonding[0m
There are two ways to do this in Linux: EQL and multilink. These are
provided as part of the Linux kernel (provided they've been selected
when the kernel was compiled). For multilink the kernel must be at
least v.2.4. Both ends of the connection must run them. Few (if any)
ISPs provide EQL but many provide Multilink.
The way it works is something like multiplexing only it's the other
way around. Thus it's called inverse-multiplexing. For the multilink
case, suppose you're sending some packets. The first packet goes out
on modem1 while the second packet is going out on modem2. Then the
third packet follows the first packet on modem1. The forth packet
goes on modem2, etc. To keep each modem busy, it may be necessary to
send out more packets on one modem than the other. Since EQL is not
packet based, it doesn't split up the flow on packet boundaries.
[1m16.2.1. EQL[0m
EQL is "serial line load balancing" which has been available for Linux
since at least 1995. An old (1995) howto on it is in the kernel
documentation (in the networking subdirectory). Unfortunately, ISPs
don't seem to provide EQL.
[1m16.2.2. Multilink[0m
Staring with kernel 2.4 in 2000, experimental support is provided for
multilink. It must be selected when compiling the kernel and it only
works with PPP.
[1m17. ISDN "Modems"[0m
To use ISDN you must have a special ISDN telephone line supplied by
your telephone company at additional cost. An ISDN "modem" is really
a Terminal Adapter (TA). Like analog modems, there are internal ones
on cards and external ones that connect to serial ports.
[1m17.1. External ISDN "Modems"[0m
Configuring an external ISDN modem on a serial port is about the same
as configuring an analog modem. The main difference is in the init
string. Unfortunately, the init strings are different for different
models of ISDN modems. There is often one AT command for a speed of
64k and another for 128k, etc. So you need to find out what init
string to use and tell it to say wvdial, etc.
[1m17.2. Internal ISDN "Modems"[0m
Support for some of these cards can be built into the 2.4 or 2.6
kernels or added as a module. The tty ports are ttyI2 for example.
The kernel documentation has an "isdn" subdirectory which describes
various drivers which support various isdn cards. A major website for
ISDN is <http://www.isdn4linux.de>
For configuring, one might use the "isdn-config" GUI. A Debian
package "isdnutils" is available. There is SuSE ISDN Howto (not a LDP
Howto) which is translated from German
<http://sol.parkland.cc.il.us/sdb/en/html/isdn.html> There is an
isdn4linux package and a newsgroup: de.alt.comm.isdn4linux. Many of
the postings are in German.
[1m18. Troubleshooting[0m
[1m18.1. My Modem is Physically There but Can't be Found[0m
The error message might also be something like "Modem not responding".
There are at least 4 possible reasons:
1. Your modem is a winmodem and no working driver has been installed
for it. Or the modem is defective or in "online data mode" where
it doesn't respond. See ``''
2. Your modem is disabled since both the BIOS and Linux failed to
enable it. It has no IO address.
3. Your modem is enabled and has an IO address but it has no ttyS
device number (like ttyS14) assigned to that address so the modem
can't be used.
4. You modem does have a ttyS number assigned to it (like ttyS4) but
you are using the wrong ttyS number (like ttyS2 instead of ttyS4).
See ``'' and/or ``wvdial'' and/or ``minicom (test modem)''
[1m18.1.1. Case 1: Winmodem[0m
For a winmodem with no driver (or a defective modem) the serial port
that the modem is on can usually be found OK. But when the wvdial
program (or whatever) interrogates that port, it gets no response
since winmodems need a driver to do anything. So you see a message
saying that no modem was found. However, it's likely that the modem
card was detected at boot-time and it displays a message implying that
a modem was found. So you're told both that the modem was found and
that it wasn't found! What it all means is that no working modem has
been found, since a modem that doesn't work has been found. Of course
it could not be working for reasons other than being a winmodem (or
linmodem) with no driver. See ``Software-based Modems (winmodems,
linmodems)''.
[1m18.1.2. Cases 2-3[0m
Cases 2. and 3. mean that no serial port device (such as /dev/ttyS2)
exists for the modem. If you suspect this, see ``Serial Port Can't be
Found''.
[1m18.1.3. Case 4: Wrong ttySx number[0m
If you are lucky, the problem is case 4. Then you just need to find
which ttyS your modem is on.
[1m18.1.4. wvdial[0m
There's a program that looks for modems on commonly used serial ports
called "wvdialconf". Just type "wvdialconf <a-new-file-name>". It
will create the new file as a configuration file but you don't need
this file unless you are going to use "wvdial" for dialing. See
``What is wvdialconf ?'' Unfortunately, if your modem is in "online
data" mode, wvdialconf will report "No modem detected". See ``minicom
(test modem)''
[1m18.1.5. minicom (test modem)[0m
Another way try to find out if there's a modem on a certain port is to
start "minicom" on the port (after first setting up minicom for that
serial port. You will need to save the setup and then exit minicom
and start it again. Then type "AT" and you should see "OK". If you
don't, try typing ATQ0 V1 EI. If you still don't get OK (and likely
don't even see the AT you typed) then there is likely no modem on the
port. This may be due to either case 1. 2. or 3. above
If what you type is really getting thru to a modem, then the lack of
response could be due to the modem being in "online data" mode where
it can't accept any AT commands. You may have been using the modem
and then abruptly disconnected (such as killing the process with
signal 9). In that case your modem did not get reset to "command
mode" where it can interact to AT commands. "Minicom" may display
"You are already online. Hangup first." (For another meaning of this
minicom message see ``You are already online! Hang up first.'') Well,
you are sort of online but you are may not be connected to anything
over the phone line. Wvdial will report "modem not responding" for
the same situation.
To fix this as a last resort you could reboot the computer. Another
way to try to fix this is to send +++ to the modem to tell it to
escape back to "command mode" from "online data mode". On both sides
of the +++ sequence there must be about 1 second of delay (nothing
sent during "guard time"). This may not work if another process is
using the modem since the +++ sequence could wind up with other
characters inserted in between them or after the +++ (during the guard
time). Ironically, even if the modem line is idle, typing an
unexpected +++ is likely to set off an exchange of control packets
(that you never see) that will violate the required guard time so that
the +++ doesn't do what you wanted. +++ is usually in the string that
is named "hangup string" so if you command minicom (or the like) to
hangup it might work. Another way to do this is to just exit minicom
and then run minicom again.
Other problems which you might observe in minicom besides no response
to AT are:
· It takes many seconds to get an expected truncated response
(including only the cursor moving down one line). See ``Extremely
Slow: Text appears on the screen slowly after long delays''
· Some strange characters appear but they are not in response to AT.
This likely means that your modem is still connected to something
at the other end of the phone line which is sending some cryptic
packets or the like.
[1m18.2. "Modem is busy"[0m
What this means depends on what program sent it. The modem could
actually be in use (busy). Another cause reported for the SuSE
distribution is that there may be two serial drivers present instead
of one. One driver was built into the kernel and the second was a
module.
In kppp, this message is sent when an attempt to get/set the serial
port "stty" parameters fails. (It's similar to the "Input/output
error" one may get when trying to use "stty -F /dev/ttySx"). To get a
few of these stty parameters, the true address of the port must be
known to the driver. So the driver may have the wrong address. The
setserial" command will display what the driver thinks but it's likely
wrong in this case. So what the "modem busy" often means is that the
serial port (and thus the modem) can't be found.
If you have a pci modem, then use one of these commands: lspci -v, or
cat /proc/pci, or dmesg to find the correct address and irq of the
modem's serial port. Then check to see if "setserial" shows the same
thing. If not, you need to run a script at boot-time which contains a
setserial command that will tell the driver the correct address and
irq.
[1m18.3. "You are already online! Hang up first." (from minicom)[0m
The modem has its CD signal on. Either you are actually online (a
remote modem is sending you a carrier) or your modem has been setup to
always send the CD signal. In minicom, type at&v to see if &C or &C0
is set. If so, CD will be on even if you are offline and you'll
erroneously get this error message. The fix is to set &C1 in the init
string or save it in the modem.
[1m18.4. I can't get near 56k on my 56k modem[0m
There must be very low noise on the line for it to work at even close
to 56k. Some phone lines are so bad that the speeds obtainable are
much slower than 56k (like 28.8k or even slower). Sometimes extension
phones connected to the same line can cause problems. To test this
you might connect your modem directly at the point where the telephone
line enters the building with the feeds for everything else on that
line disconnected (if others can tolerate such a test).
[1m18.5. Uploading (downloading) files is broken/slow[0m
Flow control (both at your PC and/or modem-to-modem) may not be
enabled. For the uploading case: If you have set a high DTE speed
(like 115.2k) then flow from your modem to your PC may work OK but
uploading flow in the other direction will not all get thru due to the
telephone line bottleneck. This will result in many errors and the
resending of packets. It may thus take far too long to send a file.
In some cases, files don't make it thru at all.
For the downloading case: If you're downloading long uncompressed
files or web pages (and your modem uses data compression) or if you've
set a low DTE speed, then downloading may also be broken due to no
flow control.
[1m18.6. For Dial-in I Keep Getting "line NNN of inittab invalid"[0m
Make sure you are using the correct syntax for your version of init.
The different init's that are out there use different syntax in the
/etc/inittab file. Make sure you are using the correct syntax for
your version of getty.
[1m18.7. I Keep Getting: ``Id "S4" respawning too fast: disabled for 5[0m
[1mminutes''[0m
Id "S4" is just an example. In this case look on the line which
starts with "S4" in /etc/inittab and calls getty. This line causes
the problem. Make sure the syntax for this line is correct and that
the device (ttyS4) exists and can be found. If the modem has negated
CD and getty opens the port, you'll get this error message since
negated CD will kill getty. Then getty will respawn only to be killed
again, etc. Thus it respawns over and over (too fast). It seems that
if the cable to the modem is disconnected or you have the wrong serial
port, it's just like CD is negated. All this can occur when your
modem is chatting with getty. Make sure your modem is configured
correctly. Look at AT commands E and Q.
If you use uugetty, verify that your /etc/gettydefs syntax is correct
by doing the following:
linux# getty -c /etc/gettydefs
This can also happen when the uugetty initialization is failing. See
section ``uugetty Still Doesn't Work''.
[1m18.8. Dial-in: When remote user hangs up, getty doesn't respawn[0m
One possible cause is that your modem doesn't reset right when DTR is
dropped after someone hangs up. Most Hayes compatible modems do this
OK with &D3. But for USR Courier, SupraFax, and some other modems,
you must set &D2 (and S13=1 in some cases). Check your modem manual
(if you have one). See ``Ending a Dial-in Call''
[1m18.9. NO DIALTONE[0m
It means exactly what it says. Someone else may be using another
telephone on the same line. You also get this error if there is no
phone line plugged into the modem, or if the phone line is somehow
broken. Try plugging a real telephone into the phone cord used by the
modem. Check it for a dialtone.
If for some reason your modem doesn't detect a dialtone, then you can
force it to dial anyway by putting X3 in the init string.
[1m18.10. NO CARRIER[0m
This means that the analog sine wave (the carrier) from the other
modem isn't present like it should be. If you were already connected,
this means that the connection has been lost. There may have been
noise on the line or a bad connection. The other modem may have hung
up on you for some reason: Perhaps the automatic login process
didn't work out OK. Perhaps PPP didn't get started OK. Perhaps a
time limit was exceeded.
If you get this error before you get connected, it means that the
carrier of the other modem wasn't detected by your modem. This may
happen if there is there is no properly working modem on the other
end. For example, an answering machine could have picked up your call
instead of a modem. NO CARRIER will also happen if the modems fail to
negotiate a protocol to use. This can happen if you have an early
V.90 modem that first tries to negotiate a high speed X2 or K56flex
protocol. These two protocols are obsolete and some ISP servers will
drop the connection (hang up) when this happens since they have no
understanding of such protocols and don't wait around long enough for
the calling modem to fallback to V.90.
If you force your modem to drop the connection by dropping the DTR
signal or sending your modem the hangup signal (ATH) you may get this
error message. But in this case you (or your software) wanted to drop
the connection so there should be no problem. In this case you are
only supposed to get NO CARRIER if data was lost. So for most cases
of dropping a connection by hangup (or by dropping DTR) you only get
an OK message. Your modem dialer program may not even display that to
you.
[1m18.11. uugetty Still Doesn't Work[0m
There is a DEBUG option that comes with getty_ps. Edit your config
file /etc/conf.{uu}getty.ttyS[4mN[24m and add DEBUG=[4mNNN[24m. Where [4mNNN[24m is one of
the following combination of numbers according to what you are trying
to debug:
D_OPT 001 option settings
D_DEF 002 defaults file processing
D_UTMP 004 utmp/wtmp processing
D_INIT 010 line initialization (INIT)
D_GTAB 020 gettytab file processing
D_RUN 040 other runtime diagnostics
D_RB 100 ringback debugging
D_LOCK 200 uugetty lockfile processing
D_SCH 400 schedule processing
D_ALL 777 everything
Setting DEBUG=010 is a good place to start.
If you are running syslogd, debugging info will appear in your log
files. If you aren't running syslogd info will appear in
/tmp/getty:ttyS[4mN[24m for debugging getty and /tmp/uugetty:ttyS[4mN[24m for
uugetty, and in /var/adm/getty.log. Look at the debugging info and
see what is going on. Most likely, you will need to tune some of the
parameters in your config file, and reconfigure your modem.
You could also try mgetty. Some people have better luck with it.
[1m18.12. (The following subsections are in both the Serial and Modem[0m
[1mHOWTOs)[0m
[1m18.13. Serial Port Can't be Found[0m
There are 3 possibilities:
1. Your port is disabled since both the BIOS and Linux failed to
enable it. It has no IO address.
2. Your port is enabled and has an IO address but it has no ttyS
device number (like ttyS14) assigned to that address so the modem
can't be used. You may need to use "setserial" to assign a ttyS
number to it.
3. Your port does have a ttyS number assigned to it (like ttyS14) but
you don't know which physical connector it is (on the back of your
PC).
See the Serial_HOWTO: "Which Connector on the Back of my PC is
ttyS1, etc?" But if you want to find which ttyS port the modem is
on see ``My Modem is Physically There but Can't be Found''
First check BIOS messages at boot-time (and possibly the BIOS menu for
the serial port). Then for the PCI bus type lspci -v. If this shows
something like "LPC Bridge" then your port is likely on the LPC bus
which is not well supported by Linux yet (but the BIOS might find it)
?? If it's an ISA bus PnP serial port, try "pnpdump --dumpregs"
and/or see Plug-and-Play-HOWTO. If the port happens to be enabled
then the following two paragraphs may help find the IO port:
[1m18.13.1. Scanning/probing legacy ports[0m
This is mainly for legacy non-PCI ports and ISA ports that are not
Plug-and-Play.
Using "scanport" (Debian only ??) will scan all enabled bus ports and
may discover an unknown port that could be a serial port (but it
doesn't probe the port). It could hang your PC. If you suspect that
your port may be at a certain address, you may try manually probing
with setserial, but it's a slow tedious task if you have several
addresses to probe. See ``Probing''.
[1m18.14. Linux Creates an Interrupt Conflict (your PC has an ISA slot)[0m
If your PC has a BIOS that handles ISA (and likely PCI too) then if
you find a IRQ conflict, it might be due to a shortage of free IRQs.
The BIOS often maintains a list of reserved IRQs, reserved for legacy
ISA cards. If too many are reserved, the BIOS may not be able to find
a free IRQ and will erroneously assign an IRQ to the serial port that
creates a conflict. So check to see if all the reserved IRQs are
really needed and if not, unreserve an IRQ that the serial port can
use. For more details, see Plug-and-Play-HOWTO.
[1m18.15. Extremely Slow: Text appears on the screen slowly after long[0m
[1mdelays[0m
It's likely mis-set/conflicting interrupts. Here are some of the
symptoms which will happen the first time you try to use a modem,
terminal, or serial printer. In some cases you type something but
nothing appears on the screen until many seconds later. Only the last
character typed may show up. It may be just an invisible <return>
character so all you notice is that the cursor jumps down one line.
In other cases where a lot of data should appear on the screen, only a
batch of about 16 characters appear. Then there is a long wait of
many seconds for the next batch of characters. You might also get
"input overrun" error messages (or find them in logs).
For more details on the symptoms and why this happens see the Serial-
HOWTO section: "Interrupt Problem Details".
If it involves Plug-and-Play devices, see also Plug-and-Play-HOWTO.
As a quick check to see if it really is an interrupt problem, set the
IRQ to 0 with "setserial". This will tell the driver to use polling
instead of interrupts. If this seems to fix the "slow" problem then
you had an interrupt problem. You should still try to solve the
problem since polling uses excessive computer resources.
Checking to find the interrupt conflict may not be easy since Linux
supposedly doesn't permit any interrupt conflicts and will send you a
``/dev/ttyS?: Device or resource busy'' error message if it thinks you
are attempting to create a conflict. But a real conflict can be
created if "setserial" has told the kernel incorrect info. The kernel
has been lied to and thus doesn't think there is any conflict. Thus
using "setserial" will not reveal the conflict (nor will looking at
/proc/interrupts which bases its info on "setserial"). You still need
to know what "setserial" thinks so that you can pinpoint where it's
wrong and change it when you determine what's really set in the
hardware.
What you need to do is to check how the hardware is set by checking
jumpers or using PnP software to check how the hardware is actually
set. For PnP run either "pnpdump --dumpregs" (if ISA bus) or run
"lspci" (if PCI bus). Compare this to how Linux (e.g. "setserial")
thinks the hardware is set.
[1m18.16. Somewhat Slow: I expected it to be a few times faster[0m
An obvious reason is that the baud rate is actually set too slow.
It's claimed that this happened by trying to set the baud rate to a
speed higher than the hardware can support (such as 230400).
Another reason may be that whatever is on the serial port (such as a
modem, terminal, printer) doesn't work as fast as you thought it did.
A 56k Modem seldom works at 56k and the Internet often has congestion
and bottlenecks that slow things down. If the modem on the other end
does not have a digital connection to the phone line (and uses a
special "digital modem" not sold in most computer stores), then speeds
above 33.6k are not possible.
Another possible reason is that you have an obsolete serial port: UART
8250, 16450 or early 16550 (or the serial driver thinks you do). See
"What are UARTS" in the Serial-HOWTO.
Use "setserial -g /dev/ttyS*". If it shows anything less than a
16550A, this may be your problem. If you think that "setserial" has
it wrong check it out. See ``What is Setserial'' for more info. If
you really do have an obsolete serial port, lying about it to
setserial will only make things worse.
[1m18.17. The Startup Screen Shows Wrong IRQs for the Serial Ports.[0m
For non-PnP ports, Linux does not do any IRQ detection on startup.
When the serial module loads it only does serial device detection.
Thus, disregard what it says about the IRQ, because it's just assuming
the standard IRQs. This is done, because IRQ detection is unreliable,
and can be fooled. But if and when setserial runs from a start-up
script, it changes the IRQ's and displays the new (and hopefully
correct) state on on the startup screen. If the wrong IRQ is not
corrected by a later display on the screen, then you've got a problem.
So, even though I have my ttyS2 set at IRQ 5, I still see
ttyS02 at 0x03e8 (irq = 4) is a 16550A
at first when Linux boots. (Older kernels may show "ttyS02" as
"tty02" which is the same as ttyS2). You may need to use setserial to
tell Linux the IRQ you are using.
[1m18.18. "Cannot open /dev/ttyS?: Permission denied"[0m
Check the file permissions on this port with "ls -l /dev/ttyS?"_ If
you own the ttyS? then you need read and write permissions: crw with
the c (Character device) in col. 1. It you don't own it then it will
work for you if it shows rw- in cols. 8 & 9 which means that everyone
has read and write permission on it. Use "chmod" to change
permissions. There are more complicated (and secure) ways to get
access like belonging to a "group" that has group permission. Some
programs change the permissions when they run but restore them when
the program exists normally. But if someone pulls the plug on your PC
it's an abnormal exit and correct permissions may not be restored.
[1m18.19. "Cannot open /dev/ttyS?"[0m
Unless stty is set for clocal, the CD pin may need to be asserted in
order to open a serial port. If the physical port is not connected to
anything, or if it's connected to something that is not powered on
(such an external modem) then there will be no voltage on CD from that
device. Thus the "cannot open" message. Either set clocal or connect
the serial port connector to something and power it on.
Even if a device is powered on and connected to a port, it may
sometimes prevent opening the port. An example of this is where the
device has negated CD and the CD pin on your PC is negated (negative
voltage).
[1m18.20. "Operation not supported by device" for ttyS?[0m
This means that an operation requested by setserial, stty, etc.
couldn't be done because the kernel doesn't support doing it.
Formerly this was often due to the "serial" module not being loaded.
But with the advent of PnP, it may likely mean that there is no modem
(or other serial device) at the address where the driver (and
setserial) thinks it is. If there is no modem there, commands (for
operations) sent to that address obviously don't get done. See ``What
is set in my serial port hardware?''
If the "serial" module wasn't loaded but "lsmod" shows you it's now
loaded it might be the case that it's loaded now but wasn't loaded
when you got the error message. In many cases the module will
automatically loaded when needed (if it can be found). To force
loading of the "serial" module it may be listed in the file:
/etc/modules.conf or /etc/modules. The actual module should reside
in: /lib/modules/.../misc/serial.o.
[1m18.21. "Cannot create lockfile. Sorry"[0m
When a port is "opened" by a program a lockfile is created in
/var/lock/. Wrong permissions for the lock directory will not allow a
lockfile to be created there. Use "ls -ld /var/lock" to see if the
permissions are OK. Giving rwx permissions for the root owner and the
group should work, provided that the users that need to dialout belong
to that group. Others should have r-x permission. Even with this
scheme, there may be a security risk. Use "chmod" to change
permissions and "chgrp" to change groups. Of course, if there is no
"lock" directory no lockfile can be created there. For more info on
lockfiles see the Serial-HOWTO subsection: "What Are Lock Files".
[1m18.22. "Device /dev/ttyS? is locked."[0m
This means that someone else (or some other process) is supposedly
using the serial port. There are various ways to try to find out what
process is "using" it. One way is to look at the contents of the
lockfile (/var/lock/LCK...). It should be the process id. If the
process id is say 100 type "ps 100" to find out what it is. Then if
the process is no longer needed, it may be gracefully killed by "kill
100". If it refuses to be killed use "kill -9 100" to force it to be
killed, but then the lockfile will not be removed and you'll need to
delete it manually. Of course if there is no such process as 100 then
you may just remove the lockfile but in most cases the lockfile should
have been automatically removed if it contained a stale process id
(such as 100).
[1m18.23. "/dev/tty? Device or resource busy"[0m
This means that the device you are trying to access (or use) is
supposedly busy (in use) or that a resource it needs (such as an IRQ)
is supposedly being used by another device and can't be shared. This
message is easy to understand if it only means that the device is busy
(in use). But it sometimes means that a needed resource is already in
use (busy). What makes it even more confusing is that in some cases
neither the device nor the resources that it needs are actually
"busy".
In olden days, if a PC was shutdown by just turning off the power, a
bogus lockfile might remain and then later on one would get this bogus
message and not be able to use the serial port. Software today is
supposed to automatically remove such bogus lockfiles, but as of 2003
there is still a problem with the "wvdial" dialer program related to
lockfiles. If wvdial can't create a lockfile because it doesn't have
write permission in the /var/lock/ directory, you will see this
erroneous message.
The following example is where interrupts can't be shared (at least
one of the interrupts is on the ISA bus). The ``resource busy'' part
often means (example for ttyS2) ``You can't use ttyS2 since another
device is using ttyS2's interrupt.'' The potential interrupt conflict
is inferred from what "setserial" thinks. A more accurate error
message would be ``Can't use ttyS2 since the setserial data (and
kernel data) indicates that another device is using ttyS2's
interrupt''. If two devices use the same IRQ and you start up only
one of the devices, everything is OK because there is no conflict yet.
But when you next try to start the second device (without quitting the
first device) you get a "... busy" error message. This is because the
kernel only keeps track of what IRQs are actually in use and actual
conflicts don't happen unless the devices are in use (open). The
situation for I/O address (such as 0x3f8) conflict is similar.
This error is sometimes due to having two serial drivers: one a module
and the other compiled into the kernel. Both drivers try to grab the
same resources and one driver finds them "busy".
There are two possible cases when you see this message:
1. There may be a real resource conflict that is being avoided.
2. Setserial has it wrong and the only reason ttyS2 can't be used is
that setserial erroneously predicts a conflict.
What you need to do is to find the interrupt setserial thinks ttyS2 is
using. Look at /proc/tty/driver/serial. You should also be able to
find it with the "setserial" command for ttyS2.
Bug in old versions: Prior to 2001 there was a bug which wouldn't let
you see it with "setserial". Trying to see it would give the same
"... busy" error message.
To try to resolve this problem reboot or: exit or gracefully kill all
likely conflicting processes. If you reboot: 1. Watch the boot-time
messages for the serial ports. 2. Hope that the file that runs
"setserial" at boot-time doesn't (by itself) create the same conflict
again.
If you think you know what IRQ say ttyS2 is using then you may look at
/proc/interrupts to find what else (besides another serial port) is
currently using this IRQ. You might also want to double check that
any suspicious IRQs shown here (and by "setserial") are correct (the
same as set in the hardware). A way to test whether or not it's a
potential interrupt conflict is to set the IRQ to 0 (polling) using
"setserial". Then if the busy message goes away, it was likely a
potential interrupt conflict. It's not a good idea to leave it
permanently set at 0 since it will put more load on the CPU.
[1m18.24. "Input/output error" from setserial, stty, pppd, etc.[0m
This means that communication with the serial port isn't working
right. It could mean that there isn't any serial port at the IO
address that setserial thinks your port is at. It could also be an
interrupt conflict (or an IO address conflict). It also may mean that
the serial port is in use (busy or opened) and thus the attempt to
get/set parameters by setserial or stty failed. It will also happen
if you make a typo in the serial port name such as typing "ttys"
instead of "ttyS".
[1m18.25. "LSR safety check engaged"[0m
LSR is the name of a hardware register. It usually means that there
is no serial port at the address where the driver thinks your serial
port is located. You need to find your serial port and possibly
configure it. See ``Locating the Serial Port: IO address IRQs''
and/or ``What is Setserial''
[1m18.26. Overrun errors on serial port[0m
This is an overrun of the hardware FIFO buffer and you can't increase
its size. Bug note (reported in 2002): Due to a bug in some kernel
2.4 versions, the port number may be missing and you will only see
"ttyS" (no port number). But if devfs notation such as "tts/2" is
being used, there is no bug. See "Higher Serial Thruput" in the
Serial-HOWTO.
[1m18.27. Modem doesn't pick up incoming calls[0m
This paragraph is for the case where a modem is used for both dial-in
and dial-out. If the modem generates a DCD (=CD) signal, some
programs (but not mgetty) will think that the modem is busy. This
will cause a problem when you are trying to dial out with a modem and
the modem's DCD or DTR are not implemented correctly. The modem
should assert DCD only when there is an actual connection (ie someone
has dialed in), not when getty is watching the port. Check to make
sure that your modem is configured to only assert DCD when there is a
connection (&C1). DTR should be on (asserted) by the communications
program whenever something is using, or watching the line, like getty,
kermit, or some other comm program.
[1m18.28. Port gets characters only sporadically[0m
There could be some other program running on the port. Use "top"
(provided you've set it to display the port number) or type "ps
-alxw". Look at the results to see if the port is being used by
another program. Be on the lookout for the gpm mouse program which
often runs on a serial port.
[1m18.29. Troubleshooting Tools[0m
These are some of the programs you might want to use in
troubleshooting:
· "lsof /dev/ttyS*" will list serial ports which are open.
· "setserial" shows and sets the low-level hardware configuration of
a port (what the driver thinks it is). See ``What is Setserial''
· "stty" shows and sets the configuration of a port (except for that
handled by "setserial"). See the Serial-HOWTO section: "Stty".
· "modemstat" or "statserial" or "watch head /proc/tty/driver/serial"
will show the current state of various modem signal lines (such as
DTR, CTS, etc.). The one in /proc also shows byte flow and errors.
· "irqtune" will give serial port interrupts higher priority to
improve performance.
· "hdparm" for hard-disk tuning may help some more.
· "lspci" shows the actual IRQs, etc. of hardware on the PCI bus.
· "pnpdump --dumpregs" shows the actual IRQs, etc. of hardware for
PnP devices on the ISA bus.
· Some "files" in the /proc tree (such as ioports, interrupts, and
tty/driver/serial).
[1m19. Flash Upgrades[0m
Many modems can be upgraded by reprogramming their flash memories with
an upgrade program which you get from the Internet. By sending this
"program" from the PC via the serial port to the modem, the modem will
store this program in its non-volatile memory (it's still there when
the power is turned off). The instructions on installing it are
usually on how to do in under Windows so you'll need to figure out how
to do the equivalent under Linux (unless you want to install the
upgrade under Windows). Sending the program to the modem is often
called a download.
If the latest version of this HOWTO still contains this request (see
``New Versions of this HOWTO'') please send me your experiences with
installing such upgrades that will be helpful to others.
Here's the general idea of doing an upgrade. First, there may be a
command that you need to send your modem to tell it that what follows
is a flash ROM upgrade. In one case this was AT** You can do this by
starting a communications program (such as minicom) and type. First
type AT <enter> to see if your modem is there and answers "OK".
Next, you need to send an file (sometimes two files) directly to the
modem. Communication programs (such as minicom) often use zmodem or
kermit to send files to the modem (and beyond) but these put the file
into packets which append headers and you want the exact file sent to
the modem, not a modified one. But the kermit communications program
has a "transmit" command that will send the file directly (without
using the kermit packets) so this is one way to send a file directly.
Minicom didn't have this feature in 1998.
Another way to send the file(s) would be to escape from the
communications program to the shell (in minicom this is ^AJ) and then:
cat upgrade_file_name > /dev/ttyS4 (if your serial port is ttyS4).
Then go back to the communication program (type fg at the command line
prompt in minicom) to see what happened.
Here's an example session for a certain Rockwell modem (C-a is ^A):
- Run minicom
- Type AT** : see "Download initiated ..."
- C-a J
- cat FLASH.S37 > /dev/modem
- fg : see "Download flash code ..."
- C-a J
- cat 283P1722.S37 > /dev/modem
- fg : see "Device successfully programmed"
[1m20. Other Sources of Information[0m
[1m20.1. Misc[0m
· man pages for: agetty(8), getty(1m), gettydefs(5), init(1),
isapnp(8), login(1), mgetty(8), setserial(8)
· Your modem manual (if it exists). Some modems come without
manuals.
· Serial Suite <ftp://scicom.alphacdc.com/pub/linux/> by Vern Hoxie
is a collection of blurbs about the care and feeding of the Linux
serial port plus some simple programs.
· The Linux serial mailing list. To subscribe, send email to
majordomo@vger.rutgers.edu, with ``subscribe linux-serial'' in the
message body. If you send ``help'' in the message body, you get a
help message. The server also serves many other Linux lists. Send
the ``lists'' command for a list of mailing lists.
[1m20.2. Books[0m
I've been unable to find a good up-to-date book on modems.
· The Complete Modem Reference by Gilbert Held, 1997. Contains too
much info about obsolete topics. More up-to-date info may be found
on the Internet.
· Modems For Dummies by Tina Rathbone, 1996. (Have never seen it.)
· The Modem Technical Guide by Douglas Anderson, 1996.
· Ultimate Modem Handbook by Cass R. Lewart, 1998.
· Black, Uyless D.: Physical Layer Interfaces & Protocols, IEEE
Computer Society Press, Los Alamitos, CA, 1996.
[1m20.3. HOWTOs[0m
· Cable-Modem mini-howto
· SuSE ISDN Howto (not a LDP Howto)
<http://sol.parkland.cc.il.us/sdb/en/html/isdn.html> or
<http://brenner.chemietechnik.uni-
dortmund.de/doc/sdb/en/html/isdn.html>
· Linux-Modem-Sharing mini-howto. Computers on a network share a
single modem for dial-out (like a shared printer).
· Modems-HOWTO: In French (Not used in creating this Modem-HOWTO)
· NET-3-4-HOWTO: all about networking, including SLIP, CSLIP, and PPP
· PPP-HOWTO: help with PPP including modem set-up
· Serial-HOWTO has info on Multiport Serial Cards used for both
terminals and banks of modems. Covers the serial port in more
detail than in the HOWTO.
· Serial-Programming-HOWTO: for some aspects of serial-port
programming
· Text-Terminal-HOWTO: (including connecting up with modems)
· UUCP-HOWTO: for information on setting up UUCP
[1m20.4. Usenet newsgroups[0m
· comp.os.linux.answers; FAQs, How-To's, READMEs, etc. about Linux.
· comp.os.linux.hardware; Hardware compatibility with the Linux
operating system.
· comp.os.linux.setup; Linux installation and system administration.
· comp.dcom.modems; Modems for all OS's
[1m20.5. Web Sites[0m
· Modem List of modems which work/don't_work under Linux modem list
<http://65.70.147.202:8080/gromitkc/winmodem.html>
· Linux Serial Driver home page <http://serial.sourceforge.net/>
Includes info about support for PCI modems.
· Hayes AT modem commands Technical Reference for Hayes (tm) Modem
Users <http://www-dcg.fnal.gov/Net/HYSTRM20.TXT>
· AT Command Set and Register Summary for Analog Modem Modules
(Cisco)
<http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis3600/analogfw/analogat.htm>
· Controlling your Modem with AT Commands
<http://www.zoltrix.com/support_html/modem/USEMODEM.HTM>
· Modem FAQs:
Navas 28800-56K Modem FAQ <http://modemfaq.home.att.net/>
· Curt's High Speed Modem Page <http://www.net-boy.com>
· Much info on 56k modems 56k Modem = v.Unreliable
<http://modemsite.com/56k/>
· Links to modem manufacturers
<http://www.56k.com/links/Modem_Manufacturers/>
· More Links to modem manufacturers <http://modems.rosenet.net/>
· < http://search.fcc.gov/> name="Search for manufacturer by FCC ID">
[1m21. Appendix A: How Analog Modems Work (technical) (unfinished)[0m
[1m21.1. Modulation Details[0m
[1m21.1.1. Intro to Modulation[0m
This part describes the modulation methods used for conventional
analog modems. Two other types of modems, cable and ADSL, use the
same modulation methods but the situation is more complicated since
they divide their frequency spectrum into multiple channels, etc.
Cable modems have to share a cable used by many other people. This
HOWTO doesn't explain this added complexity of cable and ADSL modems.
Modulation is the conversion of a digital signal represented by binary
binary (0 or 1) into an analog signal something like a sine wave. The
modulated signal consists pure sine wave "carrier" signal which is
modified to convey information. A pure carrier sine wave, unchanging
in frequency and voltage, provides no flow of information at all
(except that a carrier is present). To make it convey information we
modify (or modulate) this carrier. There are 3 basic types of
modulation: frequency, amplitude, and phase. They will be explained
next.
[1m21.1.2. Frequency Modulation[0m
The simplest modulation method is frequency modulation. Frequency is
measured in cycles per second (of a sine wave). It's the count of the
number of times the sine wave shape repeats itself in a second. This
is the same as the number of times it reaches it peak value during a
second. The word "Hertz" (abbreviated Hz) is used to mean "cycles per
second".
A simple example of frequency modulation is where one frequency means
a binary 0 and another means a 1. For example, for some obsolete 300
baud modems 1070 Hz meant a binary 0 while 1270 Hz meant a binary 1.
This was called "frequency shift keying". Instead of just two
possible frequencies, more could be used to allow more information to
be transmitted. If we had 4 different frequencies (call them A, B, C,
and D) then each frequency could stand for a pair of bits. For
example, to send 00 one would use frequency A. To send 01, use
frequency B; for 10 use C; for 11 use D. In like manner, by using 8
different frequencies we could send 3 bits with each shift in
frequency. Each time we double the number of possible frequencies we
increase the number of bits it can represent by 1.
[1m21.1.3. Amplitude Modulation[0m
Once one understands frequency modulation example above including the
possibilities of representing a few bits by a single shift in
frequency, it's easier to understand both amplitude modulation and
phase modulation. For amplitude modulation, one just changes the
height (voltage) of the sine wave analogous to changing the frequency
of the sine wave. For a simple case there could only be 2 allowed
amplitude levels, one representing a 0-bit and another representing a
1-bit. As explained for the case of frequency modulation, having more
possible amplitudes will result in more information being transmitted
per change in amplitude.
[1m21.1.4. Phase Modulation[0m
To change the phase of a sine wave at a certain instant of time, we
stop sending this old sine wave and immediately begin sending a new
sine wave of the same frequency and amplitude. If we started sending
the new sine wave at the same voltage level (and slope) as existed
when we stopped sending the old sine wave, there would be no change in
phase (and no detectable change at all). But suppose that we started
up the new sine wave at a different point on the sine wave curve.
Then there would likely be a sudden voltage jump at the point in time
where the old sine wave stopped and the new sine wave began. This is
a phase shift and it's measured in degrees (deg.) A 0 deg. (or a 360
deg.) phase shift means no change at all while a 180 deg. phase shift
just reverses the voltage (and slope) of the sine wave. Put another
way, a 180 deg. phase shift just skips over a half-period (180 deg.)
at the point of transition. Of course we could just skip over say 90
deg. or 135 deg. etc. As in the example for frequency modulation, the
more possible phase shifts, the more bits a single shift in phase can
represent.
[1m21.1.5. Combination Modulation[0m
Instead of just selecting either frequency, amplitude, or phase
modulation, we may chose to combine modulation methods. Suppose that
we have 256 possible frequencies and thus can send a byte (8 bits) for
each shift in frequency (since 2 to the 8 power is 256). Suppose also
that we have another 256 different amplitudes so that each shift in
amplitude represents a byte. Also suppose there are 256 possible
phase shifts. Then a certain points in time we may make a shift in
all 3 things: frequency, amplitude and phase. This would send out 3
bytes for each such transition.
No modulation method in use today actually does this. It's not
practical due to the relatively long time it would take to detect all
3 types of changes. The main problem is that frequent shifts in phase
can make it appear that a shift in frequency has happened when it
actually didn't.
To avoid this difficulty one may simultaneous change only the phase
and amplitude (with no change in frequency). This is called phase-
amplitude modulation. It is also called quadrature amplitude
modulation (= QAM) since there were only 4 possible phases
(quadrature) in early versions of it. This method is used today for
the common modem speeds of 14.4k, 28.8k, and 33.6k. The only
significant case where this modulation method is not used today is for
56k modems. But even 56k modems exclusively use QAM (phase-amplitude
modulation) in the direction from your PC out the telephone line.
Sometimes even the other direction will also fall back to QAM when
line conditions are not good enough. Thus QAM (phase-amplitude
modulation) still remains the most widely used method on ordinary
telephone lines.
[1m21.2. 56k Modems (V.90, V.92)[0m
The "modulation" method used for speeds above 33.6k is entirely
different than the common phase-amplitude modulation used at 33.6k and
below. Since ordinary telephone calls are converted to digital
signals at the local offices of the telephone company, the fastest
speed that you can send digital data by an ordinary telephone call is
the same speed that the telephone company uses over its digital
portion of its network (for a phone call). What is this speed?
Well, it's close to 64kbps. It's sometimes 64k and sometimes less if
bits are "stolen" for signalling purposes. If the phone Co. knows
that the link is not for voice, bits may not get stolen. The case of
64k will be presented and then it will be explained why the actual
speed is lower (56k or less --often significantly less).
Thus 64k is the absolute top speed possible (not counting date
compression) for an ordinary telephone call using the digital portion
of the circuit that was designed to send digital encodings of the
human voice. In order to use 64k, the modems need to either have
direct access to the digital portion of the circuit or be able to
determine the exact digital signal that generated a received analog
signal (and conversely). This task is far too error prone if both
sides of a telephone call have only an analog interface to the
telephone company. But if one side has a digital interface, then it's
possible (in one direction for V.90 and in both directions for V.92).
Thus if your ISP has a digital interface to the phone company, the ISP
may send out a certain digital signal over the phone lines toward your
PC. The digital signal from the ISP gets converted to analog at the
local telephone office near your PC's location (perhaps near your
home). Then it's your modem's task to try to figure out exactly what
that digital signal was. If it could do this, then transmission at
64k (the speed of the telephone company's digital signal) is possible
in this direction.
What method does the telephone company use to digitally encode analog
signals? It uses a method of sampling the amplitude of the analog
signal at a rate of 8000 samples per second. Each sample amplitude is
encoded as a 8-bit byte. (Note: 8 x 8000 = 64k) This is called
"Pulse Code Modulation" = PCM. These bytes are then sent digitally on
the telephone company's digital circuits where many calls share a
single circuit using a time-sharing scheme known as "time division
multiplexing". Then finally at a local telephone office near your
home, the digital signal is de-multiplexed resulting in the same
digital signal as was originally created by PCM. Then this signal is
converted back to analog and sent to your home. This analog to
digital conversion (and conversely) is done by telephone company
hardware called a "codec" (coder/decoder). Each PCM 8-bit byte
creates a certain amplitude of the analog signal. Your modem's task
is to determine just what that PCM 8-bit byte was, based on the analog
amplitude it detects.
This was originally called is called "modulus conversion". It's now
often called "PCM"-something since its just like encoding/decoding PCM
but with the added problem of sampling at the precise time that the
codec generated the analog voltage from the digital PCM code.
In order to determine the digital codes the telephone Co. used to
create the analog signal, the modem must sample this analog signal
amplitude at exactly the same points in time the phone Co. did when it
created the analog signal. To do this an 8kHz clock timing signal is
generated with help from a residual 4kHz signal on the analog phone
line. The creation of amplitudes to go out to your home/office at 8k
amplitudes/sec sort of creates a 4kHz signal. Suppose every other
amplitude was of opposite polarity. Then there would be a 4kHz sine-
like wave created. Each amplitude is in a sense a 8-bit symbol and
when to sample amplitudes is known as "symbol timing". The modem's
task is to insure that it's 8kHz clock runs at precisely twice the
speed of the 4kHz signal (which could drift slightly off 4kHz) and
that the modem's clock is synchronized with that used by the telephone
company's codec. The actual electronics may use much higher frequency
clocks (dividing them down) and take more than a single sample. If
you know how this synchronization works, let me know (if this is a
recent Modem-HOWTO).
Now the encoding of amplitudes in PCM is not linear. At low
amplitudes an increment of 1 in the PCM byte value represents a much
smaller increment (delta) in analog signal amplitude than would be the
case if the amplitude being sampled were much higher. Thus for low
amplitudes it's difficult to distinguish between adjacent byte values.
To make it easier to do this (for 56k modems) certain PCM codes
representing very low amplitudes are not used. This gives a larger
delta between possible amplitudes and makes correct detection of them
by your modem easier. Thus half of the amplitude levels are not used
(in the downstream direction) by V.90 or V.92. This is tantamount to
each symbol (valid amplitude level) representing 7 bits instead of 8.
This is where 56k comes from: 7 bits/symbol x 8k symbols/sec = 56k
bps. Of course each amplitude symbol is actually generated by 8-bits
but only 128 bytes of the possible 256 bytes are actually used by the
ISP sender. There is a code table mapping these 128 8-bit bytes to
the 128 7-bit bytes. It's not just a simple mapping like ignoring the
last bit. Thus to send 7 normal data bytes (8-bits) will take 8 of
the above mentioned bytes.
But it's a little more complicated that this. If the line conditions
are not nearly perfect or if the direction is upstream (V.92 only),
then even fewer possible levels (symbols) are used resulting in speeds
under 56k. Also due to US government rules prohibiting high power
levels on phone lines, certain high amplitudes levels can't be used
resulting in only about 53.3k at best for "56k" modems in the
downstream direction.
Note that the digital part of the telephone network is bi-directional.
Two such circuits are used for a phone call, one in each direction.
For V.90, the 56k signal is only used in one of these directions: from
your ISP to your PC (called the "downstream" direction). For this
V.90, the other direction (upstream, from your home/office to the ISP)
uses the conventional phase-amplitude modulation scheme with a maximum
of 36.6kbps (and not 53.3kbps). For V.92, this upstream direction
also uses the PCM method and supports up to 48 kbps. The analog
portion of the circuit from your home/office to the nearest telephone
Co. office was never intended to be bi-directional since it's only a
single twisted pair. But due to sophisticated cancellation methods
it's able to convey data simultaneously in both directions as
explained in the next subsection. It's claimed that with V.92, it's
almost impossible to get maximum thruput in both directions
simultaneously due to the difficulties of bi-directional flow on a
single circuit.
[1m21.3. Full Duplex on One Circuit[0m
Modern modems are able to both send and receive signals
simultaneously. One could call this "bidirectional" or "full duplex".
This was once done by using one frequency for sending and another for
receiving. Today, the same frequency is used for both sending and
receiving. How this works is not easy to comprehend.
Most of the telephone system "main lines" are digital with two
channels in use when you make a telephone call. What you say goes
over one digital channel and what the other person says goes over the
other (reverse) digital channel. Unfortunately, the part of the
telephone system which goes to homes (and many offices) is not digital
but only a single analog channel. If both modems were directly
connected to the digital part of the phone system then bidirectional
communication (sending and receiving at the same time) would be no
problem because two channels would be available.
But the end portion of the signal path goes over just one circuit.
How can there be two-way communication on it simultaneously? It works
something like this. Suppose your modem is receiving a signal from
the other modem and is not transmitting. Then there's no problem.
But if your modem were to start transmitting (with the other received
signal still flowing into your modem) it would drown out the received
signal. If the transmitted signal was a "solid" voltage wave applied
to the end of the line then there is no way any received signal could
be present at that point.
But the transmitter has "internal impedance" and the transmitted
signal applied to the end of the line is not solid (or strong enough)
to completely eliminate the received signal coming from the other end.
Thus while the voltage at the end of the line is mostly the stronger
transmitted signal a small part of it is the desired received signal.
All that is needed is to filter out this stronger transmitted signal
and then what remains will be the signal from the other end which we
want. To do this, one only needs to get the pure transmitted signal
directly from the transmitter (before it's applied to the line)
amplify it a determined amount, and then subtract it from the total
signal present at the end of the line. Doing this in the receiver
circuits leaves a signal which mostly came from the other end of the
line.
[1m21.4. Echo Cancellation[0m
An analog signal traveling down a line in one direction may encounter
changes in the line that will cause part of the signal to echo back in
the opposite direction. Since the same circuit is used for bi-
directional flow of data, such echos will result in garbled reception.
One way to ameliorate this problem is to send training signals once in
a while to determine the echo characteristic of the line. This will
enable one to predict the echos that will be generated by any given
signal. Then this prediction method is used to predict what echos the
transmitted signal will cause. Then this predicted echo signal is
subtracted from the received signal. This cancels out the echoes.
[1m22. Appendix B: Analog Voice Infeasible Over Non-Voice Modem[0m
Sometimes people look for software that will allow them to transmit
ordinary analog voice over a modem that doesn't support voice. It
doesn't exist since it's just not very feasible to do this. Of
course, one can use VOIP to send digital voice over a modem. And when
one makes a call and the other side picks up the line, one might be
able to hear voice for a few seconds until negotiations for a
connection begin.
But once a modem is connected, sending analog voice over it just isn't
feasible. For phase-amplitude modulation, carrier frequencies of
fixed values are used which doesn't allow the continuously variable
frequencies required in analog voice. V.90 and V.92 might be
feasible, but if line conditions deteriorate, they fall back to phase-
amplitude modulation which won't work. Furthermore, V.90 uses phase-
amplitude in one direction. Also, both V.90 and V.92 don't permit all
amplitudes to be used, which limits the waveshapes which can be
created.
[1m23. Appendix C: "baud" vs. "bps"[0m
[1m23.1. A simple example[0m
``baud'' and ``bps'' are perhaps one of the most misused terms in the
computing and telecommunications field. Many people use these terms
interchangeably, when in fact they are not! bps is simply the number
of bits transmitted per second. The baud rate is a measure of how
many times per second a signal changes (or could change). For a
typical serial port a 1-bit is -12 volts and a 0-bit is +12 v (volts).
If the bps is 38,400 a sequence of 010101... would also be 38,400 baud
since the voltage shifts back and forth from positive to negative to
positive, etc. and there are 38,400 shifts per second. For another
sequence say 111000111... there will be fewer shifts of voltage since
for three 1's in sequence the voltage just stays at -12 volts yet we
say that its still 38,400 baud since there is a possibility that the
number of changes per second will be that high.
Looked at another way, put an imaginary tic mark separating each bit
(even though the voltage may not change). 38,400 baud then means
38,400 tic marks per second. The tic marks at at the instants of
permitted change and are actually marked by a synchronized clock
signal generated in the hardware but not sent over the external cable.
Suppose that a "change" may have more than the two possible outcomes
of the previous example (of +- 12 v). Suppose it has 4 possible
outcomes, each represented by a unique voltage level. Each level may
represent a pair of bits (such as 01). For example, -12v could be 00,
-6v 01, +6v 10 and +12v 11. Here the bit rate is double the baud
rate. For example, 3000 changes per second will generate 2 bits for
each change resulting in 6000 bits per second (bps). In other words
3000 baud results in 6000 bps.
[1m23.2. Real examples[0m
The above example is overly simple. Real examples are more
complicated but based on the same idea. This explains how a modem
running at 2400 baud, can send 14400 bps (or higher). The modem
achieves a bps rate greater than baud rate by encoding many bits in
each signal change (or transition). Thus, when 2 or more bits are
encoded per baud, the bps rate exceeds the baud rate. If your modem-
to-modem connection is at 14400 bps, it's going to be sending 6 bits
per signal transition (or symbol) at 2400 baud. A speed of 28800 bps
is obtained by 3200 baud at 9 bits/baud. When people misuse the word
baud, they may mean the modem speed (such as 33.6k).
Common modem bps rates were formerly 50, 75, 110, 300, 1200, 2400,
9600. These were also the bps rates over the serial_port-to-modem
cables. Today the bps modem-to-modem (maximum) rates are 14.4k,
28.8k, 33.6k, and 56k, but the common rates over the serialPort-to-
modem cables are not the same but are: 19.2k, 38.4k, 57.6k, 115.2k,
230.4k. The high speed of 230.4k is (as of late 2000) unfortunately
not provided by most new (and old) hardware. Using modems with
V.42bis compression (max 4:1 compression), rates up to 115.2k bps are
possible for 33.6k modems. 203.2k (4 x 53.3k) is possible for 56k
modems.
Except for 56k modems, most modems run at 2400, 3000, or 3200 baud.
Even the 56k modems use these bauds for transmission and sometimes
fall back to them for reception. Because of the bandwidth limitations
on voice-grade phone lines, baud rates greater than 2400 are harder to
achieve, and only work under conditions of good phone line quality.
How did this confusion between bps and baud start? Well, back when
antique low speed modems were high speed modems, the bps rate actually
did equal the baud rate. One bit would be encoded per phase change.
People would use bps and baud interchangeably, because they were the
same number. For example, a 300 bps modem also had a baud rate of
300. This all changed when faster modems came around, and the bit rate
exceeded the baud rate. ``baud'' is named after Emile Baudot, the
inventor of the asynchronous telegraph printer. One way this problem
gets resolved is to use the term "symbol rate" instead of "baud" and
thus avoid using the term "baud". However when talking about the
"speeds" between the modem and the serial port (DTE speed) baud and
the symbol rate are the same. And even "speed" is a misnomer since we
really mean flow rate.
[1m24. Appendix D: Terminal Server Connection[0m
This section was adapted from Text-Terminal-HOWTO.
A terminal server is something like an intelligent switch that can
connect many modems (or terminals) to one or more computers. It's not
a mechanical switch so it may change the speeds and protocols of the
streams of data that go thru it. A number of companies make terminal
servers: Xyplex, Cisco, 3Com, Computone, Livingston, etc. There are
many different types and capabilities. Another HOWTO is needed to
compare and describe them (including the possibility of creating your
own terminal server with a Linux PC). Most are used for modem
connections rather than directly connected terminals.
One use for them is to connect many modems (or terminals) to a high
speed network which connects to host computers. Of course the
terminal server must have the computing power and software to run
network protocols so it is in some ways like a computer. The terminal
server may interact with the user and ask what computer to connect to,
etc. or it may connect without asking. One may sometimes send jobs to
a printer thru a terminal server.
A PC today has enough computing power to act like a terminal server
except that each serial port should have its own hardware interrupt.
PC's only have a few spare interrupts for this purpose and since they
are hard-wired you can't create more by software. A solution is to
use an advanced multiport serial card which has its own system of
interrupts (or on lower cost models, shares one of the PC's interrupts
between a number of ports). See Serial-HOWTO for more info. If such
a PC runs Linux with getty running on many serial ports it might be
thought of as a terminal server. It is in effect a terminal server if
it's linked to other PC's over a network and if its job is mainly to
pass thru data and handle the serial port interrupts every 14 (or so)
bytes. Software called "radius" is sometimes used.
Today real terminal servers serve more than just terminals. They also
serve PC's which emulate terminals, and are sometimes connected to a
bank of modems connected to phone lines. Some even include built-in
modems. If a terminal (or PC emulating one) is connected directly to
a modem, the modem at the other end of the line could be connected to
a terminal server. In some cases the terminal server by default
expects the callers to use PPP packets, something that real text
terminals don't generate.
[1m25. Appendix E: Cable and DSL modems[0m
[1m25.1. Introduction[0m
This HOWTO only deals with the common type of analog modem used to
connect PC's to ordinary analog telephone lines. There are also
higher speed analog modems that use special types of lines: cable and
DSL modems. There is also the ISDN "modem" which uses digital
signals. While this HOWTO doesn't cover such modems, some links to
documents that do may be found at the start of this HOWTO. The next 3
sub-sections: DSL, Cable, and ISDN, briefly discuss such modems. For
both DSL and Cable modems, the basic QAM modulation method is similar
to ordinary analog analog modems. See ``Combination Modulation''
[1m25.2. Digital Subscriber Line (DSL)[0m
DSL (often ADSL) uses the existing twisted pair line from your home
(etc.) to the local telephone office. This can be used if your
telephone line can accept significantly higher speeds than an ordinary
modem would use. It replaces the analog-to-digital converter at the
local telephone office with one which can accept a much faster flow of
data (in a different format of course). The spectrum of the twisted
pair line is divided up into various channels. Each channel uses QAM
modulation like ordinary modems do. Data is sent over multiple
channels. The device which converts the digital signals from your
computer to the analog signal used to represent digital data on what
was once an ordinary telephone line, is a DSL modem.
[1m25.3. Cable Modems[0m
The coaxial cables that provide for cable television in homes have
additional bandwidth not used for television, mostly at frequencies
higher than used for cable TV. This extra bandwidth may be used for
connecting computers to ISP's. However, many computers need to share
the same cable. The spectrum of the free bandwidth is split up into
channels (frequency division multiplexing) and each channel is given
time slots to which individual computers are assigned (time division
multiplexing). The cable modem converts the digital date from your
computer (from a network card: NIC) to the required analog signal, and
only broadcasts within it's assigned time slots on it's assigned
channel.
[1m26. Appendix F: Connecting 2 Modems Directly Back-to-Back (Leased[0m
[1mLines).[0m
While modems are designed to be connected to telephone lines which
have dial tones and voltages on the line, it's claimed that most
modems will communicate when just connected to each other back-to-back
via a telephone cord. To get this working, type ATD for one modem to
dial and ATA for the other modem to answer (or set it for auto
answer). Since there will be no dialtone, you may need to set ATX (or
whatever) to blind dial (force it to dial without a dialtone). If ATD
doesn't work because of no phone number, you could try ATD0 to send a
0.
If the above doesn't work, you could make a simple power supply to
emulate a telephone line. See Connecting two computers using their
modems, without a telephone line
<http://www.jagshouse.com/modem.html>.
A line without a source of voltage is sometimes called a "dry line"
and some modems exist which are designed to work on such lines (or
which can be configured to work on such lines). If you connect one of
these special modems to a line with voltage on it, it may destroy the
modem.
A leased line is one which is usually leased from the telephone
company. The end points of the line are under the control of the user
who may connect a modem at each end of the line. Leased lines may or
may not have a voltage supply on them. See the mini-howto: Leased-
Line which covers leased lines where there is neither voltage nor
dialtone on the line. One type of leased line used two pairs of wires
(one for each direction) using V.29 modulation at 9600 baud. Some
brands of leased line modems are incompatible with other brands.
[1m27. Appendix G: Fax pixels (dots)[0m
Here's some info on the bloated bandwidth required for standard fax
including the dot density. You can of course send a fax via your
modem if you dial the real telephone number of the recipient.
A4 paper: 216mm (horizontal) * 297mm (vertical)
normal mode 8dots/mm * 3.85dots/mm
fine mode * 7.7dots/mm
extra fine mode *15.4dots/mm
Each dot is either white or black and thus 1 bit. One sheet of A4
paper using fine mode is (216*8) * (297*7.7) = about 4 million dots.
With a compression ratio of 8:1 it takes about 50 seconds at 9600bps
for transmission.
[1m28. Appendix H: Stty Hanging Problem (prior to 2000)[0m
Here's a problem that existed prior to the year 2000 or thereabouts.
It's since been fixed. If -clocal is set and there is no CD signal,
then the "stty" command will hang and there is seemingly no way to set
clocal to stop the hanging (except by running minicom). But minicom
will restore -clocal when it exits. One way to get out of this is to
use minicom to send the "AT&C" to the modem (to get the CD signal) and
then exit minicom with no reset so that the CD signal always remains
on. Then you may use stty again.
[1m29. Appendix G: Antique Modems[0m
[1m29.1. Introduction[0m
By "antique" I mean modems with speeds of 14.4 kbps or less. Many of
them were made in the 1980s. Faster modems are also included if they
use a proprietary protocol. This appendix compares the antique modems
with the modern ones. You should read it if you are interested in
modem history or are intending to actually use an antique modem.
Also, many modern modems and software still support the old protocols
and you might find that such old protocols have been configured by
mistake.
[1m29.2. Old CCITT (ITU) and Bell Protocols[0m
· Bell 103 300 bps; frequency shift keying = FSK (1962)
· V.21 300 bps; frequency shift keying (used a different
frequency than Bell 103) (1964)
· V.23 1200/75 bps and 600/75 bps asymmetric; 75 bps is the
reverse channel; frequency shift keying = FSK (1964)
· Bell 212A 1200 bps; quadrature differential phase shift keying =
QDPSK = DPSK
· V.22 1200 bps; fallback to 600 bps ; QDPSK = DPSK (1980)
· V.22bis 2400 bps; QAM (1984)
· V.32 9600 bps; QAM (1984 but not widely used until years
later)
· V.32bis 14400 bps; QAM (1991)
QAM= Quadrature Amplitude Modulation. The word "Quadrature" is
short for "quadrature differential phase shift keying" =QDPSK
[1m29.3. Historical Overview[0m
[1m29.3.1. Teletypes and dumb terminals[0m
Prior to 1960, 110 bps modems were used for teletype machines (like an
electric typewriter only much more noisy). What one typed at a
teletype (or had saved on punched paper tape) could be printed on a
remote teletype located far away. No computer was involved.
Then in 1960 AT$amp;T came out with a 300 bps modem (for use on it's
phone system). Such slow and expensive modems were later mainly used
for transmitting data between mainframe computers or for connecting a
dumb terminal to a mainframe computer over phone lines. Many dumb
terminals didn't even have a screen display, but printed on paper what
you typed at the keyboard along with responses from the computer.
[1m29.3.2. PCs and BBSs[0m
With the advent of the personal computer (PCs) in the early 1980s, one
could use a modem to dial into a remote mainframe computer. In this
case, the PC was used like a dumb terminal. But now files could be
transferred and one PC could connect to another via modems.
The 1980s saw the rise of the Bulletin Board System (BBS). A BBS was
just a computer with a modem listening for incoming calls. The public
could dial up a BBS with a modem and then download free software,
participate in discussions on various topics, play on-line games, etc.
Dialing in to a BBS was something like going to an Internet site.
Except that to go to another BBS site, you would need to dial another
number (and possible pay long distance telephone charges). Many BBSs
would have a monthly charge but some were run by volunteers and were
free. Many companies established BBSs for customers that contained
support information, catalogs, etc. In the early 1990s, BBSs were
booming. By the mid 1990s some even offered Internet connections.
For some history of BBSs see Sysops' Corner: History of BBSing
<http://sysopscorner.thebbs.org/bbshist.html>
[1m29.3.3. The Internet[0m
Then came the advance of Internet in the mid 1990s which resulted in
the demise of the BBSs near the end of the 1990s. Some BBSs became
websites, but when BBSs were dying in droves, websites were quite
expensive so most BBSs just disappeared. The Internet contained far
more information than any one BBS could maintain so BBSs were no
longer competitive.
Modems permitted the public to connect to the Internet. In the 1990s,
Modems became fast, cheap and widely used. Then in the late 1990s,
faster non-analog "modems" appeared: ISDN, DSL, and cable. The
history of these isn't in this HOWTO.
[1m29.3.4. Speeds[0m
Before V.32 (9600 bps), modems typically had speeds of 300 to 2400
bps. Some super fast ones had much higher speeds (such as 19.2k bps)
and used non-standard protocols. To utilize these "fast" ones, both
modems for a connection needed to support the same proprietary
protocol which often meant that they must be the same brand.
Prior to the V.42 standard for error correction and the V.42bis (1990)
standard for data compression, the MNP standards were usually used for
both error correction and data compression. An X.PC error correction
standard was used on some commercial data networks. Compression and
error correction were available on some 2400 bps modems.
From 1960 to 1980 most modems only had a speed of 300 bps (which was
also 300 baud). This is only 0.3kbps. Modern modems are over 100
times faster. Some old-slow modems are still in use so they are not
really "antique" quite yet.
[1m29.4. Proprietary protocols, etc.[0m
These were used in order to obtain higher speeds before more
standardized higher speeds became established. The modem at the other
end needs to support the same protocol for this to work. The dates
shown below may be only approximate.
· PEP (Packetized Ensemble Protocol 1985): 18k (at best).
· Turbo PEP: 23k 1994?
· Hayes Express 96: 9.6k (Hayes 1987)
· HST: 9.6k (US Robotics 1986)
· HST: 14.4k (US Robotics 1989)
· HST: 16.8k (US Robotics 1992)
· V.32 terbo: 19.2k (AT$amp;T 1993)
· V.FastClass: 28.8k (Rockwell 1993)
· X2 :57.3k (US Robotics 1997)
· K56: Flex 57.3k (Rockwell 1997)
The PEP used as much bandwidth as feasible by splitting the
spectrum into as many as 512 sub-bands. It was supported by Ven-
Tel's Pathfinder and Telebit's Trailblazer.
[1m29.5. Autobauding[0m
This term has a few different meanings. In general it means either
the automatic adjustment of modem-to-modem speed or of modem-to-
serial_port speed.
[1m29.6. Modem-to-modem Speed[0m
Modern modems negotiate the modem-to-modem speed and protocol when
they first connect to each other and normally connect to each other at
the highest possible speed. If one side can't negotiate, the other
side should accept whatever speed and protocol that the fixed side has
available. Except that some modern modems may no longer support some
of the antique protocols. As a result of negotiations, one modem may
need to use a lower speed than its maximum in order to communicate
with the other modem. This is sometimes called "autobauding" or
"automode". It might also be called "fallback". A more intuitive use
of the word "fallback" is where both modems automatically lower their
speed due to a noisy line. While autobauding is normally the default,
setting a fixed modem-to-modem speed instead of autobauding is done
with either an AT command like or by a register like S37.
Early modems didn't have such autobauding or fallback. If you have
such a modem, it will likely work OK if the other modem you connect to
is a modern one that can adjust it's speed and protocol to yours. But
a problem arises if both modems which want to communicate with each
other are both antique and don't support automode. In this case they
need to be manually set to the same speed and protocol.
Even when this automode existed, there was sometimes a limited choice
of speed (like only 1200/300 bps). In olden days (rarely today), a
computer dial-in site might have one phone number a certain speed
(like say 2400) and another phone number for a different speed (say
1200). It was often not quite this simple as there might be a few
different phone number for one speed, or one phone number might
support say only a couple of speeds (like 1200/300). Also one phone
number might support only a certain protocol such as the Bell 212A
modem. Once a site obtained modems that could support a wider variety
of speeds and protocols, then there was no need to have different
groups of phone lines.
[1m29.7. Modem-to-serial_port Speed[0m
[1m29.7.1. Same speed required[0m
For old modems (mostly under 9600 bps) the modem-to-serial_port speed
had to be the same as the modem-to-modem speed. This was because data
flowed straight thru the modem without "speed buffering" (storing
bytes) inside the modem. This meant that both the modem's serial port
and the computer's serial port had to be set to this speed. That is,
both ends of the serial cable had to be set for this speed.
One might erroneously reason that if the serial port speed was higher
than the modem-to-modem speed, all would work OK since then there
would be no bottleneck in the serial line. This works OK in the
direction from the modem to the PC since a higher speed line can have
a lower thruput speed due to greater time spacing between bytes. But
disaster strikes for the flow from the PC to the modem since it would
flow into the modem at a speed faster than the modem could transmit
the data. Data would be lost since there is no speed buffering.
[1m29.7.2. Equalizing speed[0m
If a modem had only one modem-to-modem speed (or was set by software
or physical switches to only operate at one speed), then this wasn't a
problem since one would just set the PCs serial port for this speed.
And the modem would set it's serial port for this speed. Another way
make the speeds equal is for the modem to detect the PC's serial port
speed and then set both it's serial speed and it's modem-to-modem
speed the same. This will be explained later.
But for modems that used more than one modem-to-modem speed there's a
problem. In that case it's not known in advance at what speed the
modem will connect to another modem. For example, if a fixed speed
modem dialed in to you modem and your modem supported the remote
modems fixed speed, then that's the speed it would connect at. If the
PC's serial port speed had been previously set to a different speed,
then this speed needs to be changed.
But setting the computer's serial port to the modem-to-modem speed was
a problem since the modem has no way to directly give commands to the
PCs serial port to change it's speed. Only system software can do
that. The modem finds out what speed to use based on negotiations
with the other modem and thus the change of this serial port speed
can't be done in advance. How does the modem communicate its modem-
to-modem speed to the system software?
[1m29.7.3. Use "CONNECT" message to set speed[0m
Here's one way to do it. Consider the case of a dial-in modem that
others dial into. A getty program will be used to send a login prompt
thru the modems to a user's terminal screen. Getty will also be the
system software that changes the speed of the serial port. The modem
will tell getty what modem-to-modem speed it's using by sending getty
a "CONNECT" message giving the modem-to-modem speed (such as "CONNECT
2400").
But there's one problem here. How does one insure that the "CONNECT"
message, which the modem sends to getty via the serial port, is sent
at the same speed as the PC's serial port which is expecting a
"CONNECT" message? Here's how it's done.
When the modem is first sent an init string, the modem detects the
speed of the computer's serial port and sets it's modem-to-serial_port
speed to this value. Now it can communicate with getty and the
"CONNECT" message can get thru.
To sense the speed the modem has examined the "AT" at the beginning of
the string. This is sometimes also called autobauding. For modern
modems, this same modem-to-serial port speed is always retained, even
after the modem connects to another modem and regardless of what the
modem-to-modem speed is. But for our old modem this initial serial
speed may need to be changed later to that of the modem-to-modem speed
once a connection is made.
For example, getty gets a CONNECT 2400 from the modem and switches the
PC's serial port speed to 2400. The modem also switches its serial
port speed to 2400. Now both ends of the modem serial cable are at
2400 and there is no speed mismatch. Then getty sends a login prompt
out over the phone line thru the modems. The 2400 bps is now both the
modem-to-modem speed and the modem-to-serial_port speed. Problem
solved. Mgetty can do this by configuring it for "autobauding" but
it's only of use for very old (and slow) modems.
For dialing out, the same method is used, but now the communication
software must handle it instead of getty.
[1m29.7.4. Setting modem-to-modem speeds by the serial speed[0m
Another way to switch modem-to-modem speed was by using a modem
feature where the modem would set its modem-to-modem speed to be the
same as the modem-to-serial port speed it detected. The Bn AT
commands would enable this and determine what protocol to use for each
speed. So with this enabled, setting the serial speed by the computer
would also set the modem-to-modem speed to be the same. This should
result in this modem being inflexible in any speed negotiations
between the modems.
[1m29.7.5. Manual bauding[0m
Another (but cruder) way to solve the serial speed problem when
dialing in to a site was to get the remote site to change it's modem-
to-modem speed to match your serial port speed. It works like this:
The person trying to login over a modem connection doesn't see any
login prompt because of a speed mismatch. So the person trying to
login hits a "break" key to send a break signal over the phone line
(via modem) to getty on the remote machine. A break signal will
always get through even if there is a speed mismatch in a serial line.
The remote getty gets this break signal and switches the remote's
serial port to the next speed as specified in its getty configuration
file. This new remote serial port speed causes the remote modem to
switch to the same modem-to-modem speed as previously configured by
the ATB command. Then the local modem would transmit the login prompt
over the local's serial line at this speed. If one doesn't see a
login prompt, then they hit the break key again and a new speed is
tried. This continues until the remote getty finally gets the speed
correct (equal to the serial speed set on the local PC) and a login
prompt finally displays. Note that PC keyboards have no "break" key
but dumb terminal keyboards did. Mgetty, agetty, and uugetty can do
this obsolete break method and it's called "manual bauding".
[1m29.7.6. Unsupported speeds[0m
In Linux, there's a problem if the speed is set to a speed not
supported by Linux's serial port (for example 7200 bps). You may dial
out and connect at 7200 bps (both modem-to-modem and modem-to-
serial_port speed) but you only see garbage since Linux doesn't
support 7200 on the serial port. Once you connect there is no simple
way to hang up because even the +++ escape sequence can't be sent to
the modem over a 7200 baud interface.
[1m29.7.7. Modern modems, speed buffering[0m
To dial out by the antique method using some modern modems set &Q0 N0
and S37=5 (if you want 1200 bps). Some of the S17 settings vary with
the make of modem. S37=0 is the default that connects the modern way
at the highest speed supported.
Modern modems can use almost any serial port speed. It doesn't depend
at all on modem-to-modem speed. To do this, they employ speed
buffering and flow control. Speed buffering means that modems have
buffers so that there can be a difference between the modem-to-modem
speed and the modem-to-serial_port speed. If the flow entering the
modem is faster than the flow exiting it, the excess flow is simply
stored in a buffer in the modem. Then to prevent the buffer from
overflowing, the modem sends a flow control signal to stop the input
flow to it. This is true for either direction of flow. See ``Flow
Control'' for more details.
[1m29.8. Before AT Commands[0m
Hayes introduced the AT command set and other modem manufacturers
adopted it as a standard. Before the AT commands, many modems used
dip switches to configure the modem. Another command set is the CCITT
V.25bis command set. Some modems supported both CCITT and AT
commands. The CCITT V.25bis also specifies how Synchronous modem-to-
serial_port communication is to take place using either the ASCII or
8-bit EBCDIC character sets.
[1m29.9. Acoustic-Coupling[0m
This is where one connects a modem to a telephone using audio tones
that one can hear. The modem contains a microphone and speaker which
"talks" directly into the telephone handset without using any wires.
It's "wireless" in a sense but uses sound waves instead of radio
waves. The modem speaker is placed in contact with the telephone
microphone (on the handset) so that the tones from the modem go into
the telephone. The modem microphone, picks up tones from the
telephone handset speaker. This scheme is called "acoustic coupling".
A major problem is that outside noises can interfere and cause errors.
The advantage is convenience: There are no cables to plug in. Most
modems that could do this were only 300 baud, but higher speeds were
used too. It's said that 9600 bps didn't work very well using this
scheme.
[1m29.10. Data Compression and Error Correction[0m
MNP 2, 3, or 4 were used for error correction. MNP 5 was compression.
Modern modems generally use V42 (error correction) and V42bis
(compression). Many modems support both MNP and V42.
END OF Modem-HOWTO
