<HTML
><HEAD
><TITLE
>Reboot the system, modify LILO configuration file</TITLE
><META
NAME="GENERATOR"
CONTENT="Modular DocBook HTML Stylesheet Version 1.56"><LINK
REL="HOME"
TITLE="Hard Disk Upgrade Mini How-To"
HREF="index.html"><LINK
REL="PREVIOUS"
TITLE="Remove the old disk"
HREF="remove.html"><LINK
REL="NEXT"
TITLE="Acknowledgements"
HREF="acknowledgements.html"></HEAD
><BODY
CLASS="SECT1"
BGCOLOR="#FFFFFF"
TEXT="#000000"
LINK="#0000FF"
VLINK="#840084"
ALINK="#0000FF"
><DIV
CLASS="NAVHEADER"
><TABLE
WIDTH="100%"
BORDER="0"
CELLPADDING="0"
CELLSPACING="0"
><TR
><TH
COLSPAN="3"
ALIGN="center"
>Hard Disk Upgrade Mini How-To</TH
></TR
><TR
><TD
WIDTH="10%"
ALIGN="left"
VALIGN="bottom"
><A
HREF="remove.html"
>Prev</A
></TD
><TD
WIDTH="80%"
ALIGN="center"
VALIGN="bottom"
></TD
><TD
WIDTH="10%"
ALIGN="right"
VALIGN="bottom"
><A
HREF="acknowledgements.html"
>Next</A
></TD
></TR
></TABLE
><HR
ALIGN="LEFT"
WIDTH="100%"></DIV
><DIV
CLASS="SECT1"
><H1
CLASS="SECT1"
><A
NAME="REBOOT"
>12. Reboot the system, modify <SPAN
CLASS="ACRONYM"
>LILO</SPAN
> configuration file</A
></H1
><P
>Reboot the system. If you have problems, you can use the boot diskette
you just make. To do so, you may have to modify your
<SPAN
CLASS="ACRONYM"
>BIOS</SPAN
>'s boot-up sequence to
<TT
CLASS="COMPUTEROUTPUT"
>A:, C:</TT
>.</P
><P
>You should modify the file
<TT
CLASS="FILENAME"
>/etc/lilo.conf</TT
> in case you later want to run
<SPAN
CLASS="ACRONYM"
>LILO</SPAN
> again. Here's an example of how the file can look:
<TABLE
BORDER="0"
BGCOLOR="#E0E0E0"
WIDTH="100%"
><TR
><TD
><PRE
CLASS="PROGRAMLISTING"
>boot=/dev/hda # Install LILO on first hard
# disk.
map=/boot/map # Location of "map file".
install=/boot/boot.b # File to copy to floppy's
# boot sector.
prompt # Have LILO show "LILO boot:"
# prompt.
timeout=50 # Boot default system after 5
# seconds. (Value is in tenths of
# seconds.)
image=/boot/vmlinuz # Location of Linux kernel. The
# actual name may include a version
# number, for example
# "vmlinuz-2.0.35".
label=linux # Label for Linux system.
root=/dev/hda1 # Location of root partition on
# new hard disk. Modify this as
# appropriate for your system.
read-only # Mount partition read-only at
# first, to run fsck.</PRE
></TD
></TR
></TABLE
>
</P
><DIV
CLASS="FORMALPARA"
><P
><B
>Slackware only. </B
>Use <B
CLASS="COMMAND"
>image=/vmlinuz</B
>.</P
></DIV
></DIV
><DIV
CLASS="NAVFOOTER"
><HR
ALIGN="LEFT"
WIDTH="100%"><TABLE
WIDTH="100%"
BORDER="0"
CELLPADDING="0"
CELLSPACING="0"
><TR
><TD
WIDTH="33%"
ALIGN="left"
VALIGN="top"
><A
HREF="remove.html"
>Prev</A
></TD
><TD
WIDTH="34%"
ALIGN="center"
VALIGN="top"
><A
HREF="index.html"
>Home</A
></TD
><TD
WIDTH="33%"
ALIGN="right"
VALIGN="top"
><A
HREF="acknowledgements.html"
>Next</A
></TD
></TR
><TR
><TD
WIDTH="33%"
ALIGN="left"
VALIGN="top"
>Remove the old disk</TD
><TD
WIDTH="34%"
ALIGN="center"
VALIGN="top"
> </TD
><TD
WIDTH="33%"
ALIGN="right"
VALIGN="top"
>Acknowledgements</TD
></TR
></TABLE
></DIV
></BODY
></HTML
>
