###########################################################################
# $Id: postfix.conf,v 1.13 2007/05/14 17:33:27 mrc Exp $
###########################################################################

# You can put comments anywhere you want to.  They are effective for the
# rest of the line.

# this is in the format of <name> = <value>.  Whitespace at the beginning
# and end of the lines is removed.  Whitespace before and after the = sign
# is removed.  Everything is case *insensitive*.

# Yes = True  = On  = 1
# No  = False = Off = 0

Title = "Postfix"

# Which logfile group...
LogFile = maillog

# Only give lines pertaining to the postfix service...
#
# Note: both variables below must contain the same "postfix" RE.
# If you change postfix's syslog_name for any smtpd listener
# you will need to replace "postfix" below with an appropriate
# RE to capture the desired log entries.  For example:
#
#       *OnlyService = "postfix\d?/[-a-zA-Z\d]*"
#       $postfix_Syslog_Name = "postfix\d?"
#
# will capture postfix/smtpd, postfix2/smtpd, ..., postfix9/smtpd

*OnlyService = "postfix/[-a-zA-Z\d]*"
$postfix_Syslog_Name = "postfix"

#
# Set the variable below to specify the maximum report width.
# for Detail <= 10
#
#$postfix_Max_Report_Width = 100

# Set the variable below to the value set for "recipient_delimiter"
# in your postfix configuration, if you want your recipient email
# addresses split into their user + extension.
#
#$postfix_Recipient_Delimiter = "+"

# Width of IP addresses for columnar output.  Change to 40 for IPv6 addresses
#$postfix_ipaddr_width = 15

# The variables below control the maximum output level for a given
# category.  A level of 1 indicates only one level of detailed output in
# the Detailed report section.  The Summary section is only available
# at logwatch --Detail level >= 5.  Increasing the Detail level
# by one adds one level of additinal detail in the Summary section.
# For example, Detail 5 would output one additional level of detail,
# Detail 6 two levels, etc. all the way up to 10.  Finally, Detail
# 11 yeilds uncropped lines of output.

# uncomment and change the value of a variable below to control
# the maximum detail level for the named category
#$postfix_MsgsSent = 1
#$postfix_MsgsSentLmtp = 1
#$postfix_MsgsDelivered = 1
#$postfix_MsgsForwarded = 1
#$postfix_PanicError = 1
#$postfix_FatalErrors = 1
#$postfix_QueueWriteError = 1
#$postfix_MessageWriteError = 1
#$postfix_DatabaseGeneration = 1
#$postfix_MailerLoop = 1
#$postfix_StartupError = 1
#$postfix_MapProblem = 1
#$postfix_PrematureEOI = 1
#$postfix_ProcessExit = 1
#$postfix_Hold = 1
#$postfix_CommunicationError = 1
#$postfix_SaslAuthFail = 1
#$postfix_LdapError = 1
#$postfix_WarningsOther = 1
#$postfix_RelayDenied = 1
#$postfix_RejectHelo = 1
#$postfix_RejectUnknownUser = 1
#$postfix_RejectRecip = 1
#$postfix_RejectSender = 1
#$postfix_RejectClient = 1
#$postfix_RejectUnknownClient = 1
#$postfix_RejectUnknownReverseClient = 1
#$postfix_RejectRBL = 1
#$postfix_RejectHeader = 1
#$postfix_RejectBody = 1
#$postfix_RejectSize = 1
#$postfix_RejectConfigError = 1
#$postfix_RejectInsufficientSpace = 1
#$postfix_RejectMilter = 1
#$postfix_MsgsDeferred = 1
#$postfix_Deferrals = 1
#$postfix_BounceLocal = 1
#$postfix_BounceRemote = 1
#$postfix_Discarded = 1
#$postfix_ReturnedToSender = 1
#$postfix_ConnectionLost = 1
#$postfix_ConnectionLostOverload = 1
#$postfix_ConnectToFailure = 1
#$postfix_TimeoutInbound = 1
#$postfix_HeloError = 1
#$postfix_IllegalAddrSyntax = 1
#$postfix_WarningHeader = 1
#$postfix_RBLError = 1
#$postfix_MxError = 1
#$postfix_NumericHostname = 1
#$postfix_SmtpConversationError = 1
#$postfix_TooManyErrors = 1
#$postfix_HostnameVerification = 1
#$postfix_HostnameValidationError = 1
#$postfix_Deliverable = 1
#$postfix_Undeliverable = 1
#$postfix_PixWorkaround = 1
#$postfix_SaslAuth = 1
#$postfix_TlsConnectFrom = 1
#$postfix_TlsConnectTo = 1
#$postfix_TlsUnverified = 1
#$postfix_TlsOffered = 1
#$postfix_RejectWarnRelay = 1
#$postfix_RejectWarnHelo = 1
#$postfix_RejectWarnUnknownUser = 1
#$postfix_RejectWarnRecip = 1
#$postfix_RejectWarnSender = 1
#$postfix_RejectWarnClient = 1
#$postfix_RejectWarnUnknownClient = 1
#$postfix_RejectWarnUnknownReverseClient = 1
#$postfix_RejectWarnRBL = 1
#$postfix_RejectWarnInsufficientSpace = 1
#$postfix_RejectWarnVerify = 1
#$postfix_RejectWarnConfigError = 1
#$postfix_PolicySPF = 1
#$postfix_PolicydWeight = 1

# vi: shiftwidth=3 tabstop=3 et